碳強度模式 的英文怎麼說
中文拼音 [tànqiángdùmóshì]
碳強度模式
英文
carbon intensity mode-
The degrees of crystallinity of pure ptfe under the different conditions of water cooling, air cooling and furnace - varying cooling were made comparison by xrd. the thermal stability of pure ptfe and solid lubricant was analyzed by dsc - tg ; the composition and valence state of elements in the surface of carbon fiber, solid lubricant before and after friction test and lubricant transfer film were characterized by xps ; the frictional property of solid lubricant was tested by pin and disk test rig. the frictional wear property of solid lubricant between embedded bearing sleeve and steel axle friction pair ring was tested by special simulate test machine, the hardness of solid lubricant was tested by pm ; the compression strength of solid lubricant was tested by material test machine
用sem表徵原料微觀結構、摩擦表面及潤滑轉移膜表面形貌：用xrd進行原料物相分析，及比較水冷卻、空氣冷卻、隨爐冷卻三種工藝條件下的純聚四氟乙烯樹脂的結晶度；用dsc - tg分析純聚四氟乙烯樹脂及固體潤滑劑的熱穩定性；用xps表徵碳纖維表面、固體潤滑劑摩擦前後表面、潤滑轉移膜表面的元素組成、價態變化；用銷盤式摩擦磨損試驗機對固體潤滑劑進行摩擦性能測試；採用專用的臺架模擬試驗機對固體潤滑劑鑲嵌軸承套與鋼軸摩擦副間的摩擦磨損性能進行測定；用萊次偏光顯微鏡（ pm ）測試固體潤滑劑的硬度；用材料試驗機測試固體潤滑劑的抗壓強度等。The properties of cn thin films such as their morphology, component, crystal structure and the bonding structure and the relation between those properties and the gas - phase reaction parameters were discussed, showing that the deposition of p - c3n4 thin film is the compete result of various reaction processes in the dynamics balance conditions ; the process of cn films depo sition is diagnosed in situ through the optical emission spectra technique, the effects of experimental parameters on the concentration of the precursors and the gas - phase reactions in the plasma have been obtained ; the main reaction precursors for film deposition identified ; the relation between the characteristics of cn thin films and the reaction process in the plasma is analyzed. the cn thin films deposition under different substrate temperatures in high pressure pe - pld shows that the si atom of the substrate has participated the cn films growth process, based on this the growth mode of cn thin films on the si substrate is proposed. the further experiment of cn thin films deposition on si substrate scratched by diamond as well as covered with fe catalyzer has been attempted, which indicates that changing the dynamics conditions of the surface reaction can alter the growth characteristic of the cn thin films and can enhance obviously the films growth rate
採用pld技術進行了碳氮化合物薄膜沉積，得到了含氮量為21at的cn薄膜；研究了襯底溫度和反應氣體壓強對薄膜結構特性的影響，給出了cn薄膜中n含量較小、 sp ~ 3鍵合結構成分較少和薄膜中僅含有局域cn晶體的原因；引入脈沖輝光放電等離子體增強pld的氣相反應，給出了提高薄膜晶態sp ~ 3鍵合結構成分和薄膜的含n量可行性途徑；應用pe - cvd技術以ch _ 4 + n _ 2為反應氣體並引入輔助氣體h _ 2 ，得到了含n量為56at的晶態cn薄膜；探討了cn薄膜形貌、成分、晶體結構、價鍵狀態等特性及其與氣體壓強和放電電流的關系，證明了- c _ 3n _ 4薄膜沉積為滿足動力學平衡條件的各種反應過程的競爭結果；採用光學發射譜技術對cn薄膜生長過程進行了實時診斷，得到了實驗參量對等離子體中活性粒子相對濃度和氣相反應過程的影響規律，給出了cn薄膜沉積的主要反應前驅物，揭示了cn薄膜特性和等離子體內反應過程之間的聯系；採用高氣壓pe - pld技術研究了不同襯底溫度條件下cn化合物薄膜的結構特性，揭示了si原子對薄膜生長過程的影響，給出了si基表面碳氮薄膜的生長模式；在金剛石研磨和催化劑fe處理的si襯底上進行cn薄膜沉積，證明了通過控制材料表面動力學條件可以改變碳氮薄膜結構特性，並可顯著提高晶態碳氮材料的生長速率。The carbon fibers with low strength are broken easily according to thermal tension and bend stress damage models, and the carbon fibers with high modulus are broken easily according to thermal shear stress damage model in spite of less damage caused by heat. the carbon fibers with surface glue of epoxy resin are damaged easily in physical and chemical ways because of high oxygen extent and rigidity of epoxy resin
低強度碳纖維容易在熱應力拉伸或彎折破壞模式下損傷；高模量碳纖維高溫損傷小，但國防科學技術大學研究生院學位論文容易以熱應力剪切破壞模式下斷裂;環氧樹脂表面膠剛性較大，氧含量較高，使碳纖維容易受到化學損傷和熱應力彎折損傷，均不宜用來制備c燈sic復合材料。
分享友人