磨損特性 的英文怎麼說

中文拼音 [mósǔntèxìng]
磨損特性 英文
wear characteristics
  • 磨 : 磨動詞1 （摩擦） rub; wear 2 （研磨） grind; mull; polish 3 （折磨） grind down; wear down [out]:...
  • 損 : Ⅰ動詞1 （減少） decrease; lose 2 （損害） harm; damage 3 [方言] （用尖刻的話挖苦人） speak sarcas...
  • 特 : Ⅰ形容詞（特殊; 超出一般） particular; special; exceptional; unusual Ⅱ副詞1 （特別） especially; v...
  • 性 : Ⅰ名詞1 （性格） nature; character; disposition 2 （性能; 性質） property; quality 3 （性別） sex ...
  • 磨損 : wear and tear; abrasive wear; abrase; abrade; detrition; wear; scuff; wear out; fray; battering; ...
  • 特性 : characteristic（s）; character; performance; features; properties; behaviour; response; character...
  1. Study on the tribological behavior of monel alloy

    航用蒙乃爾合金摩擦磨損特性的研究
  2. Aim of this study was to meet the need for development of tribological parts in pumps. at room temperature tribological properties of different sliding pairs of silicon carbide and alumina - based ceramics were tested using a laboratory tribometer in the ring - on - plate geometry under reciprocating sliding linear contact in different media, such as distilled water, aggressive media and air

    本文針對目前泵用摩擦零部件材料發展的需要，在實驗室摩擦磨損試驗機上研究了按環/塊線接觸方式作往復運動條件下的碳化硅和氧化鋁基陶瓷材料摩擦副在水、化學腐蝕性介質作潤滑劑和無潤滑時室溫下的摩擦磨損特性。
  3. Study on the abrasion behavior of carburizing carbonitriding steel for pump body

    碳氮共滲鋼水泵體的磨損特性研究
  4. Friction and wear performance on fretting wear of steel wires in hoisting ropes

    提升鋼絲繩的鋼絲微動摩擦磨損特性研究
  5. Wear characteristics analysis of the pivot in high - speed micro - rotor systems

    高速微轉子樞軸磨損特性分析
  6. Wearing characteristic of ti6al4v in high dry sliding friction

    高速干滑動摩擦磨損特性研究
  7. Standard test method for ranking resistance of plastic materials to sliding wear using a block - on - ring configuration

    用環形結構塊料給塑料材料的抗滑動磨損特性分等的標準試驗方法
  8. The rolls wear characteristics and work roll wear pattern were analyzed theoretically and the quantitative analysis were made in shape control and effect factor in accordance with the rolling conditions

    從理論上分析了輥系在軋制中的磨損特性，工作輥磨損輥型的計算方法，根據實際軋制工況對其板形的調控、影響因素進行了定量分析。
  9. The effects of heat treatment on dry friction and tribological properties under water lubricating are also studied elementarily

    本文還初步探討了熱處理對復合材料干摩擦磨損特性的影響及復合材料在水潤滑時的摩擦磨損特性及磨損機理。
  10. Effect of wc addition on erosion - wear behavior of fused ni60 alloy self - fluxing coating

    60自熔合金噴焊層沖蝕磨損特性的影響
  11. The friction and wear behavior of dlc gradient film on tj6a14v alloy substrate sliding against ultra - high molecular weight polyethylene was investigated by comparing with that of ti6a14v alloy against the same counterpart under the same testing conditions

    研究了dlc梯度薄膜材料與uhmwpe組成的摩擦副的生物摩擦學性能，探討了摩擦磨損機理。 ti6a14v基dlc梯度薄膜材料具有較好的減摩特性和耐磨損特性。
  12. 3. the diamond segment wear process was analyzed by testing the weight of segment before and after sawing. the patterns of wear and breakage of diamond grits and bond wear mechanism of the blade were analyzed based on the observation on the working surface of the saw blade by stereo microscope and scanning electronic microscope

    採用稱重法測量鋸切過程鋸片節塊磨損量，並通過計算磨削比，分析了混凝土鋸切過程金剛石節塊的磨損特性及其影響因素，並採用sem和體視顯微鏡觀察節塊不同部位工作表面和金剛石的磨損破壞情況，研究了金剛石磨損破壞的主要形式和胎體材料的磨損形態。
  13. Wear - resistance of micro - arc oxidation layer on aluminum alloy

    鋁合金微弧氧化陶瓷層的磨損特性
  14. Nano structure and tribological performance of v c dual implanted steel

    雙注入鋼納米結構和抗磨損特性
  15. Research and development work on friction wear characteristics of mosi

    2材料摩擦磨損特性的研究與發展
  16. Microstructure and wear resistance of brush - plated ni nano - sio2 composite coating

    2顆粒鎳基復合刷鍍層組織與磨損特性
  17. Research on characteristics of friction and wear of high speed steel w6mo5cr4v

    激光相變硬化高速鋼的摩擦磨損特性研究
  18. The wear mechanism of tungsten carbide particle reinforced steel matrix composites was studied according to the frictional and wear characteristics and the scanning electron microscopy photographs of worn surfaces after wear testing. the effect of heat treatment and tungsten carbide content on wear resistance was investigated as well

    結合磨損特性曲線和不同磨損時間的摩擦面sem照片，分析了wc鋼復合材料的磨損機理，並討論了不同熱處理工藝和wc顆粒含量對wc鋼復合材料磨損性能的影響。
  19. Dry friction - wear properties and wear mechanisms of the pairs of mosi2 against crwmn steel

    鋼干摩擦磨損特性及磨損機理的研究
  20. Standard test method for wear preventive characteristics of lubricating fluid four - ball method

    潤滑液防磨損特性的標準試驗方法
分享友人
分享到 Line

分享到臉書