空轉程序步 的英文怎麼說
中文拼音 [kōngzhuǎnchéngxùbù]
空轉程序步
英文
dummy step- 空 : 空Ⅰ形容詞（不包含什麼; 裏面沒有東西或沒有內容; 不切實際的） empty; hollow; void Ⅱ名詞1 （天空） s...
- 轉 : 轉構詞成分。
- 程 : 名詞1 （規章; 法式） rule; regulation 2 （進度; 程序） order; procedure 3 （路途; 一段路） journe...
- 步 : Ⅰ名詞1 （步度; 腳步） pace; step 2 （階段） stage; step 3 （地步; 境地） condition; situation; st...
- 空轉 : [機械工程]1 （機器在沒有負載時的運轉） idling; racing; runfree; blank run 2 （車輪滑轉不前） turn...
- 程序 : 1 （進行次序） order; procedure; course; sequence; schedule; ground rule; routing process 2 [自動...
-
The content of this thesis comes from the fujian natural science found following research task 。 it studies on a space cantilever single beam attached to a moving support 。 inertia forces which are brought by the support ' s movement ， are acceded to the equivalent initiative forces and the equivalent initiative moments 。 when we consider the relation of the forces and deformation ， we change the method of material mechanical analysis to the elastic mechanical analysis 。 further more ， we discusses the feasibility of the method which uses the multi - rigid - body discrete model to simulate the dynamic characteristic of a elastic body 。 first ， the finite segment method is adopted to establish the models of the beam 。 based on kane ' s equations ， dynamic math - model for the beam are derived 。 and by use of c - language and runge - kutta procedure ， the computer - oriented procedure can give the whole responses of the beam 。 second ， with compare to the numerical examples ， the method which uses the multi - rigid - body discrete model to simulate the dynamic characteristic of a elastic body which is under the condition of movement is verified to be feasible 。
本論文為福建省自然科學基金后續研究課題，以已知支撐運動的單個空間懸臂梁為對象，在等效主動力與等效主動力矩中加入支撐轉動引起的慣性力，並在考慮力與變形關系時，用更一般的彈性力學分析代替材料力學分析，進一步研究用多剛體離散模型來模擬其動力學特性的可行性。首先，用有限段建立機械臂的多剛體離散模型，用kane動力學方法建立其動力學方程。並用c語言編制演算法程序，採用了四階runge - kutta積分程序求解微分方程組，給出構件的全部動態歷程。The main module of sensorless pmsm vector control such as voltage sensing, current sensing, smo rotor position estimation, speed calculation, generation of sine and cosine, vector coordinate transformation, pi regulators, svpwm vector modulation are all accomplished in the pwm interrupt service routines
永磁同步電機無位置傳感器矢量控制的主要模塊如電壓采樣、電流采樣、滑模轉子位置估算、速度計算、正餘弦值生成、矢量坐標變換、比例積分調節器、空間電壓矢量脈寬調制等都是在pwm中斷服務子程序中完成。Introduced the second order analysis of the thin - walled members based on the theory of the rotation of a cross section around a fixed axis, and discussed the general methods of the loading capacity and the space stability coefficient for the thin - walled columns. used a programme, a large amount of space stability coefficient of t - shaped and l - shaped axes columns with a initial bend was computed to gain the curves of the columns. the procedure of the computation behaved the simplification and the convenience of the method
介紹了以定軸轉動理論為基礎的薄壁柱空間穩定二階分析方法，初步論證了以此為基礎的薄壁柱空間穩定承載力的驗算及空間穩定系數的計算方法，並藉助程序對具有初彎曲的各種「 t 」形和「 l 」形軸壓柱的空間穩定系數進行了計算，作出其柱子曲線圖，從而驗證了此方法的可行性和簡便性，同時提出以此為基礎對鋼結構截面優化的方法。
分享友人