空轉齒輪 的英文怎麼說

中文拼音 [kōngzhuǎnchǐlún]
空轉齒輪 英文
idle gear
  • 空 : 空Ⅰ形容詞（不包含什麼; 裏面沒有東西或沒有內容; 不切實際的） empty; hollow; void Ⅱ名詞1 （天空） s...
  • 轉 : 轉構詞成分。
  • 齒 : Ⅰ名詞1 （牙; 牙齒） tooth 2 （物體上齒形的部分） a tooth like part of anything 3 [書面語] （年齡...
  • 輪 : Ⅰ名1 （輪子） wheel 2 （像輪子的東西） wheel like object; ring; disc 3 （輪船） steamer; steamboa...
  • 空轉 : [機械工程]1 （機器在沒有負載時的運轉） idling; racing; runfree; blank run 2 （車輪滑轉不前） turn...
  • 齒輪 : gear [rack; toothed] wheel; （toothed） gear; wheel gear
  1. Analyse the tooth geometry of klingelnberg cyclo - palloid spiral bevel gear., according to the relative position and kinematic relation of the cutter heads, virtual crown gear and the processed wheel blank, established the system of coordinates of the gear cutting, dedcuced the tooth face equation of the virtual crown gear, according to relations of the gear cutting and space theory of engagement, deduced the tooth face equation of klingelnberg cyclo - palloid spiral bevel gear, and drawing the three - dimensional graphs of the virutal crown gear and klingelnberg cyclo - palloid spiral bevel gear according to the design and setting parameters

    對克林貝格擺線齒錐齒輪進行齒面幾何分析。根據銑齒加工中刀盤、搖臺和輪坯的相對位置和相對運動關系建立了切齒嚙合坐標系，由矢量的旋轉推導了產形輪齒面方程;根據空間嚙合原理和切齒嚙合關系推導了被加工齒輪的齒面方程;由設計參數和銑齒調整參數計算得到齒面離散數據，繪制了產形輪和擺線齒錐齒輪的三維齒形。
  2. The design undertaken mainly from the following aspects : 1, mechanism ddesign : included the base and the joints : 2, trasmission mechanism design : adopted a synchronous toothelike transmission bell ; 3, balance system design : adopted springs and a brake and a lay air cylinder ; 4, design parameter and verify alculation ; 5, established motion equation by d - h method ; 6, simulated the motion locus by matlab software ; 7 ^ mapping out the part drawing or asesembly drawing

    本設計主要是從以下幾個方面入手： 1 、機構設計：包括底座和臂關節的設計； 2 、傳動機構設計：將驅動電機安裝在底座上，利用同步齒型帶、離合器傳遞手臂的動力；利用齒輪傳動帶動底座回轉； 3 、平衡系統設計：採用了彈簧平衡系統、電磁式制動器和單向延時氣缸； 4 、設計參數和校核計算； 5 、用d ? h法建立運動學方程； 6 、利用matlab軟體對手臂的運動空間進行模擬； 7 、利用autocad2000繪圖：包括零件圖和裝配圖。
  3. In this paper, we designed the structure of the gear and rack in this actuating mechanism, elaborated the theory of its formation, and deduced the profile function and gearing function of the gear and rack. furthermore, we deduced the inherent radius of going around a turn under certain circumstance, the condition of the correct gearing and the continuous transmission. in order to make the mechanism move steady, we designed the derivation mechanism and manufacture the modle

    本文對該傳動機構中的漸開線柱齒鼓形齒輪和空間齒條的結構進行了設計，並給出了齒輪和齒條的成型原理，推導出了漸開線柱齒鼓形齒輪和空間齒條的齒廓參數方程、嚙合方程;進一步分析並確定了漸開線柱齒鼓形齒輪、空間齒條在給定嚙合傳動條件下所能實現的固有轉彎半徑和運動約束條件，並對其側隙及效率進行了計算和分析。
  4. At first the paper begin to study the foundation of digital curved face and space meshing principle, introduce the basic knowledge of curve theory and curved face theory, explain the mathematical tools of vector turning and coordinate conversion in the paper ; analyse the motion and relative motion of rigid body, provide the condition of gear driving continuous contact and equation of conjugate meshing

    論文首先從參數化曲面和空間嚙合原理基礎出發，介紹了曲線論和曲面論的基本知識，對課題研究重的數學工具矢量回轉和坐標變換進行了說明;分析了剛體的運動和相對運動，根據空間嚙合原理給出了輪齒傳動連續接觸的條件和共軛條件方程。
  5. An aeroengine power - turbine 1 ( superscript st ) stage rotor shrouded blade is taken for an example in the article, tightness of shroud and contact force 、 blade body stress under working state and assembly state are calculated by finite element contact analysis method, influence of working load ( temperature and centrifugal force ) is mainly analyzed

    摘要以航空發動機動力渦輪一級帶鋸齒形葉冠的轉子葉片為例，用有限元接觸分析方法對裝配和工作狀態下的葉冠緊度和葉冠接觸力、葉身應力進行了計算和分析，著重考察了工作載荷（溫度和離心力）對葉冠接觸力的影響。
  6. Change traditional shaft structure, adopt unique output constamt mesh structure, only 2 pair ( tradition is 4 pairs ) of gears idle when neutral, reduce the synchronous inertia improve shifting performance greatly, and increase the neulral noise level

    一改傳統的三軸結構，採用獨特的輸出減速結構，怠速時僅有2對齒輪空轉（傳統4對以上） ，有效降低各檔同步慣量，使操作性能大大提高，並有效改善空檔噪聲。
分享友人
分享到 Line

分享到臉書