端蓋 的英文怎麼說
中文拼音 [duāngě]
端蓋
英文
end cap; end closure; end cover; end housing; head cover; shell cover-
The ends of the tubular furnace are closed to minimize convection currents inside the furnace
把管式爐的前後端蓋緊,是爐內的對流減少到最低限度。Intercooler end cap
中間冷卻器端蓋Turn the locking bolt so that it is fixed on the bake cover or the flange plate
安裝后必須將鎖緊螺母鎖緊在電機後端蓋或法蘭盤上。The thesis developed the optimization design software of geometric parameter for the worm gear including strength check module, the drawing contact lines module, the change lines of tooth thickness of worm, and the parametric modelling software for the reducer which includes parametric modelling of parts and assembly. the cad prototype system is very convenient because of its accessible interfere, simple operation and written in chinese. by input design parameters , the cad system can make optimization design and strength check for the worm gear , draw contact lines of tooth flank of worm - gear and change line of tooth thickness of worm , judge if the tooth flanks of worm undercut and if the sideward tooth of worm - gear hob come to a point , make project design and structure design for the reducer and draw its 2d parts and assembly
研究和開發了平面二次包絡環面蝸桿傳動的參數優化設計和校核軟體系統:包括幾何參數設計計算模塊,強度校核模塊,繪制齒面接觸線模塊,蝸桿齒厚變化曲線模塊和蝸桿根切判別模塊;開發了平面二次包絡環面蝸桿減速器外形與結構尺寸數據庫以及傳動效率數據庫,建立了平面二次包絡環面蝸桿傳動公差及極限偏差數據庫;開發了平面二次包絡環面蝸桿減速器參數化建模軟體:包括零部件的參數化建模模塊和裝配圖的參數化建模模塊,其中零部件的參數化建模包括蝸桿軸系的參數化建模、蝸輪軸系的參數化建模、箱體的參數化建模、端蓋的參數化建模、軸承的參數化建模和其它零部件的參數化建模軟體模塊。Air cooler of air compressor, end cover opened, waterside surface cleaned with brush
空壓機冷卻器,端蓋打開,水面用毛刷清潔。Whin the power is off, the electromagnet loses electromagnetic force. the armature is pushed by the spring and sticks to endshield of the motor immediately, the rotation is stopped therefor
當電機失電時電磁鐵失電,銜鐵立即被彈簧頂住,使制動盤與電機後端蓋壓合在一起,停止轉動。Housing end plug
殼體端蓋The kind of welding equipment is suitable forwelding the qarts in appplications of heat exchanger in - out water pipe port of electical heater and hot pipe fittings simple operation low lost and good seam foring are the advan tages. it is an essential and special equipment in the profression of tube - making electrical and solar water heaters
該系列焊接設備適用於太陽能熱水器端蓋及水箱內受到影響上的進出水管、熱管接頭、電加熱器接頭及搪瓷水箱進出水管的自動化焊接,焊縫盛開有美觀、效率高、成本上升低,是制桶業、太陽能熱水器、電熱水器等行業必不可少的專用設備。Commutater end head felt pad
整流子端蓋阻油氈Application of the built - in turning - tool on general lathe to process endplates
端蓋組合刀架在普通車床上的應用The simulation and manufacture of the end cap pressure sensor
端蓋壓頭模擬與研製Writing and marking instruments - specification for end closures
書寫工具和標記工具.端蓋規范Permanently sealed and lubricated ball bearings front and rear
前後端蓋裝有永久密封和自潤滑的滾珠軸承。Smelting and heat treatment technology of astm a216 wca steel casting cover
大型鑄鋼端蓋的冶煉及熱處理工藝The simulation analysis of radiated noise from a gearbox cover of motorcycle
摩托車變速箱端蓋輻射噪聲模擬分析Conveyer drive shaft end cover
輸送機主動軸端蓋The rising blocker cover top plate
端蓋頂部Application of pci2000 card and mixed programming in noise measurement of bevel gears
空調電機端蓋沖壓拉深工序的動態模擬Turn the hollow bolt so that it is fixed on the bake cover or the flange plate
安裝后將鎖緊螺母鎖緊在電機後端蓋或法蘭盤上。These series motors can be used for home electric appliance, pumps, fans, and recording meters, etc
鋁殼機座端蓋底腳高強度的密封圈可供軸鍵和保護器分享友人