端鉸 的英文怎麼說

中文拼音 [duānjiǎo]
端鉸 英文
end hinge
  • 端 : Ⅰ名詞1 （東西的頭） end; extremity 2 （事情的開頭） beginning 3 （門類; 方面） item; point 4 （原...
  • 鉸 : Ⅰ動詞[口語]1. （用剪子剪斷東西） cut with scissors 2. （用絞刀切削） bore with a reamer; ream Ⅱ名詞（指鉸鏈） hinge
  1. From the analysis, some suggestion about joint rigidity design is put forward : 1. joint initial rigidity can be enhanced within the limited range when to increase end - plate thickness ; 2. the rigidity and ultimate moment can be enhanced obviously when to adopt the beam with inclined section or to add axilla at the connections between beam and column ; 3. withm the permissive construction condition, exteriorly extended end - plate inclinedly placed is suggested to be applied firstly ; 4. when the rate of joint rigidity to beam rigidity, that is called, is less than 0. 1, the joints can be regarded as zero - rigidity joints ; on the other hand, if is more than 26, it is rigid connection joints

    採用斜截面梁並在樑柱交接處局部加腋能明顯提高節點剛度和梁的抗彎能力； 3在允許的施工條件下，應優先採用外伸式端板斜放節點，有利於提高節點剛度，進而提高節點的抗彎能力； 4節點剛度與其連接構件的剛度比值0 . 1時，可按鉸接節點設計； 26時，可按剛接節點設計。
  2. Its upper end is hinge connected to a trestle on top of the tower head.

    它的上端與塔端上的支架成鉸接。
  3. Calculation of out - of - plane stability of bending members with box sections

    兩端鉸接楔形壓彎桿平面外穩定
  4. Based on the research to the stability variable cross - section beam, the bending defection differential equation of the variable cross - section beam in critical state of bucking is established. according to the edge condition of the structure, the differential equation is solved and bucking equation of variable cross - section beam is created. we can get the algorithm which can be used to calculate the equivalent inertia moment of the variable cross - section lattice structure when it is regarded as constant cross - section of solid web beam

    對變截面格構式構件的穩定性計算進行了初步的研究，通過建立變截面構件臨界狀態下彎曲變形的微分方程，根據變形邊界條件，得到了兩端鉸支的變截面梁失穩特徵方程，提出了幾種特殊形式的變截面格構式構件等效為等截面實腹式構件時等效慣性矩的計算方法。
  5. By calculating large quantity of examples, this text studies earthquake resistant behavior of tapered portal frame with pined bases and analyzes its natural frequency, natural period of vibration and vibration mode. by comparing interior forces of pillar top, beam end and span midpoint in two conditions that seismic action effect participates combination of forces and not when portal frame is n ' t changed, ensure conditions that combination of seismic action effect has controlling f unction during tapered portal frame design, and tapered portal frame demands anti - earthquake design

    本文通過大量算例分析，研究柱腳鉸接楔形變截面門式剛架的抗震性能，並對其自振頻率、振型進行了分析；通過比較地震作用效應參與荷載組合與不參與荷載組合兩種情況下，樑柱截面尺寸不變時，柱上端、梁端、跨中截面處的內力大小，確定在什麼情況下地震作用效應組合起控製作用，變截面門式剛架需要進行抗震設計。
  6. Design of a new type of hinge electric connector

    新型鋁質鉸鏈式接線端子設計
  7. The main shuchural features of the new electric single - girder overhead travelling crane presented in this paper is as follows : using a special gisder section to provide simple production technology and light weight ; dopting hinged connection at one end between main glrders and end carrages instead of the rigid connection at both ends, eliminating the three - point supporting problem with the crane and thus improving the travelling perfomance ; extending crane wheels life contributed to the combination of no - flange crane wheels and horizontal rollers

    提供種生產工藝簡單、自重輕的主梁截面，並將單梁起重機主、端梁的剛性連接改為端用鉸接連接，解決了在製造和軌道安裝時因誤差而造成的大車運行三條腿現象，提高了運行性能；用可調大車運行水平輪中心距的設計，代替帶輪緣的大車輪，提高大車輪的使用壽命。
  8. Meanwhile, the rotational capability of the plastic hinge on the end of the passed - joint hypo - beam determine the capability of dissipation earthquake energy and occurrence of the process of internal force redistributing in the last period under earthquake force of the structure system in this test

    3 .邊梁的抗扭性能和梁端「扭轉塑性鉸」的轉動性能對整個結構抗震性能的影響至關重要，因而在工程設計中應注意邊梁的抗扭設計
  9. Before installing, be sure pipe ends are reamed and threads are cut to size

    在安裝之前，要確保管道末端經過鉸孔，螺紋長度切割適中。
  10. Before installing the valve, be sure that the pipe ends are reamed and threads are cut to size

    在安裝閥門之前，要確保管道末端經過鉸孔，螺紋長度切割適中。
  11. The influence of legs " tolerance and spherical joints " ( huke joints ) clearance on errors of terminal platform is analyzed using monte - carlo technique

    利用蒙特卡洛技術模擬分析了驅動桿桿長誤差和球鉸（虎克鉸）間隙對終端平臺誤差的影響。
  12. Vibrations of an axially transporting beam are investigated

    摘要研究帶有扭轉彈簧兩端鉸支軸向運動梁的橫向振動。
  13. Vibrations of an axially transporting beam with torsional springs and simply supported

    帶有扭轉彈簧兩端鉸支軸向運動梁的橫向振動分析
  14. On the basis of simplified calculation model presented by doctor wangxiaoping, some finite element models are set up. by finite element model program sap93, an analysis of static models of 18m - span and 30m - span w666 acmr in different supporting conditions is made. also a study on the relation between definite support displacement, which reflect variational stiffness of substructure represented by steel column or reinforced concrete column, and load - carrying capacity mechanical performance is made too

    本文以w666金屬拱型波紋屋頂為研究對象，沿用王小平博士的簡化計算模型，對18m 、 30m跨波紋拱兩端不同支座形式（鉸支、固支和彈性支座）分別利用有限元計算程序sap93進行計算分析，研究波紋拱在不同跨度，不同支座形式下，不同外荷載作用時對該結構受力性能及穩定承載力的影響，同時分析下部支承鋼柱、鋼筋混凝土柱的剛度變化體現為允許支座位移的大小與結構受力性能及穩定承載力之間的關系。
  15. In this paper, slender columns with the two ends hinged are considered. an iterative computer analysis procedure taking into account the second - order effect of the axial load is proposed to predict this complete load - deformation process

    本文針對兩端鉸接的任意截面鋼-砼組合長柱，考慮長柱在偏心荷載作用下的附加彎矩影響（二階效應） ，提出了一種數值迭代的計算機方法進行全過程分析。
  16. 5 ) the secondary moment postpones coming of plastic hinge on frames. in other words, it reduces requisition of rotation ability of section. therefore, it maybe improve modulation ability of frame

    （ 5 ）初始次彎矩的存在，推遲了梁端塑性鉸的出現，也就是說降低了彎矩重分佈對梁端轉動能力的要求，從而有可能提高總調幅能力。
  17. Industrial valves - end - to - end and centre - to - end dimensions for butt welding end valves ; german version en 12982 : 2000

    工業閥門.鉸鏈焊接端閥門端對端和中心對末端尺寸
  18. The contents include as follows : the influencing factors of the displacement ductility factor of the unbonded partially prestressed concrete frame structures, such as stirrup reinforcement characteristic value, nominal shear span ratio, axial compression ratio, the appearing order of plastic hinges and partial prestressing ralio ( ppr ) are discussed. the formula of displacement ductility factor of the unbonded partially prestressed concrete frame structures is suggested by regression analysis. with regard to the aseismic design and the request of ductility and energy dissipation, the restriction of the flat - beam / column sectional size and aseismic reinforced design are discussed

    本文主要包括以下內容：討論了配箍特徵值、名義剪跨比、軸壓比、塑性鉸出現順序、預應力度等因素對無粘結部分預應力混凝土框架位移延性系數的影響，回歸了考慮影響因素的位移延性系數計算公式；對無粘結部分預應力混凝土扁梁框架結構，闡述了抗震設計對扁梁、柱截面尺寸的要求與限制；對滿足延性和耗能要求的無粘結部分預應力混凝土扁梁控制截面抗震配筋進行了探討；通過對無粘結部分預應力混凝土扁梁梁端的受力分析，改進了以往扁梁梁端扭矩設計值計算公式。
  19. Optimal design of the stability of compression bar under the constraint of elastically hinged support at both ends

    兩端彈性鉸支約束下壓桿穩定的優化設計
  20. The two kinds of joint connection half - rigidity characteristic about gabled frames are discussed. the criterion among rigid connection, zero rigidity connection, half rigidity connection is determined ; the joint ' s moment and rotation angle curve is analyzed ; the calculation method about joint initial rigidity is brought forward ; the ultimate moment ' s calculation formula is deduced ; the result calculated by the formulas is compared to one calculated by the norm ' s formulas

    探討了門式剛架兩種端板節點連接的半剛性特性，確定了節點剛接、鉸接和半剛接劃分的標準；分析了節點受力時的彎矩轉角曲線關系；提出了節點的初始剛度的計算方法；提出了節點極限彎矩的計算公式，並與規范關于節點抗彎承載力計算的結果進行了比較。
分享友人
分享到 Line

分享到臉書