端面密封 的英文怎麼說

中文拼音 [duānmiànmìfēng]
端面密封 英文
butt-end packing
  • 端 : Ⅰ名詞1 （東西的頭） end; extremity 2 （事情的開頭） beginning 3 （門類; 方面） item; point 4 （原...
  • 面 : Ⅰ名詞1 （頭的前部; 臉） face 2 （物體的表面） surface; top 3 （外露的一層或正面） outside; the ri...
  • 密 : Ⅰ名詞1 （秘密） secret 2 [紡織] （密度） density 3 （姓氏） a surname Ⅱ形容詞1 （距離近; 空隙小）...
  • 端面 : end face; end plane; end surface; head face; side surface; terminal face
  1. Two sets of back - to - back assembled mechanical seal bia, and together with a shared spring can form a double mechanical seal

    由二套bia機械密封背靠背安裝，共用一個彈簧可組成一套雙端面機械密封型式。
  2. The innovative dishing ring not only possesses end - face sealing capacity, but also has some radial seal and clean function

    改進的碟形密封圈不但具有端面密封能力，而且將具有一定的徑向密封和擦拭功能。
  3. The dishing ring seals belong the end face sealing parts, and act as sealing by some axial compression. because of different distribution of internal pressure and temperature, the friction inside the end - face is also different at all area

    碟形密封圈屬于端面密封元件，依靠一定的軸向壓縮量進行密封，由於端面內壓力分佈、溫度分佈不均，端面內的摩擦狀況也不是處處相同。
  4. Butt - end packing

    端面密封
  5. Effects of parameters of spiral groove gas face seals on seal performance

    螺旋槽端面干氣密封的參數研究
  6. Study of stiffness and leakage rate of spiral groove dry gas face seals

    螺旋槽乾式氣體端面密封的剛度和泄漏量研究
  7. Metallic tube connections for fluid power and general use - o - ring face seal connectors

    用於液壓傳動和一般用途的金屬管接頭. o形圈端面密封管接頭
  8. The influence of waviness and taper of seal faces to the operating performance at slow speed of gas face seal

    低速運轉氣膜機械密封端面波度和錐度對其密封性能的影響
  9. Characteristic of gas film between spiral groove dry gas seal faces

    螺旋槽干氣密封端面間氣膜特性
  10. According to achievements in research, using face - radial sealing structures can adapt to the developing trend of increasing rotary speed of cone bit to a certain extent in lubricating system of bearing seal, which is cramp to bit service life

    本文的研究表明，在偉l ]約鉆頭壽命的軸承密封潤滑系統中，採用端面一徑向組合密封結構能夠在一定程度上適應牙輪鉆頭轉速提高的發展趨
  11. To enhance the reliability of bearing seal of cone bit, this paper plans to adopt face - radial combination sealing structures ; that is to say, end - face and radial seal are arranged in one bit simultaneously. the nonlinear finite element method is applied to analyze and optimize the design of sealing structures

    為了提高牙輪鉆頭軸承密封的可靠性，本文設計採用端面-徑向組合密封結構，即在一隻鉆頭中同時布置端面和徑向密封，採用非線性有限元方法對密封結構進行分析和優化。
  12. Experimental research on the leakage of two kinds of dry gas seal

    兩種不同槽形氣體端面密封泄漏量的試驗研究
  13. Doing so revealed a hydrophobic meaning water - repellent tip that allows the viral harpoon to latch on more securely to the cell membrane, which is also hydrophobic. it also provided researchers with more insight into the dramatic structural change that the f protein undergoes while performing its task. when not in use, the f protein looks like a mushroom, and its hydrophobic tip is folded into a compact form, safely hidden inside the cap

    在沒有碰到人體細胞時， 「副流感病毒5型」細胞表層的「融合蛋白」看起來就像一個蘑菇，防水頂端嚴密封閉，且安全地藏在蘑菇帽子下面當病毒接觸到人體細胞時，蘑菇帽子會突然破裂開來，防水頂端也像魚叉一樣暴露出來，並陷入人體細胞膜內。
  14. Detail specification for fixed tantalum electrolytic capacitors - porous anode, polar non - solid electrolyte - tubular insulated metallic case, ptfe elastomer seal, axial wire terminations - full plus additional assessment level

    固定式鉭介質電容器詳細規范.極性非固體介質多孔陽極.軸向引線終端ptfe彈性密封管狀絕緣金屬殼.全面附加評定級
  15. To obtain satisfying performance, the sea1 end faces of rotating ring and static ring of the mechanica1 seal must keep para11e1 or approximately paral1e1 each other

    欲使密封具有良好的性能，則必須做到受載后的動、靜環密封端面間保持平行或近似平行的幾何形狀。
  16. Therefore, it is f very important to accurate1y ca1cu1at ing the mechanica1 deformat ion of the ring for carrying out des igning and manufacturing good mechanica1 - sea1 ing products

    因此，機械密封動、靜環端面力變形準確的分析和計算對于設計、製造出性能優良的機械密封產品是至關重要的。
  17. Three kinds of injection sleeves construction, materials, surface treatment and application ranges of floating end face seal ring by die casting are expounded

    敘述浮動端面密封環壓力鑄造的三種壓射套結構、材料和表面處理工藝及其應用范圍。
  18. Abstract : three kinds of injection sleeves construction, materials, surface treatment and application ranges of floating end face seal ring by die casting are expounded

    文摘:敘述浮動端面密封環壓力鑄造的三種壓射套結構、材料和表面處理工藝及其應用范圍。
  19. Mechanical seal : use of wb2 and st non - water - cooled adjustable end face sealing technology, composed of silicon carbide, high purity alumina ceramic, packing ptfe and graphite etc

    機械密封：採用wb2型、 st型不用冷卻水可調式端面密封技術，由碳化硅，高純度氧化鋁陶瓷、填充四氟，石墨等材料製成。
  20. 6, turn son to carry noodles to seal completely an adoption adjustable seal completely device, from compound material and metal alloy inside of circle wreath get in touch with, donot need lubricant lubrication, sealing completely function good, structure simple, adjust to maintain convenience. turned bearings in order to roll over bearings, use the function good life span to grow

    6轉子端面密封採用可調密封裝置，由復合材料與合金圈內環接觸，不需要潤滑油潤滑，密封性能良好結構簡單調整維修方便。轉了軸承為滾動軸承，使用性能良好壽命長。
分享友人
分享到 Line

分享到臉書