粘結強度 的英文怎麼說

中文拼音 [niánjiēqiángdù]
粘結強度 英文
adhesive strength
  • 粘 : 粘動詞（粘附） glue; stick; paste; adhere to; bond
  • 結 : 結動詞（長出果實或種子） bear （fruit）; form （seed）
  • 強 : 強形容詞（強硬不屈;固執） stubborn; unyielding
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  1. To improve the binding strength between the deck slabs and deck surfacing layer of badong changjiang river highway bridge and to provide the surfacing layer with anti - cracking ductility, a series of technical measures has been taken in the construction of the deck surfacing of the bridge, including those of embedding binding reinforcement in the deck slabs, spraying inorganic binding agent between the slabs and layer, replacing part of the cement with micro expansion agent and adding appropriate amount of polypropylene fibers to the concrete

    摘要巴東長江公路大橋橋面鋪裝，通過採取預埋橋面粘接鋼筋、噴塗無機界面粘結劑、用微膨脹劑替代部分水泥、在混凝土中摻入適量的聚丙烯纖維等措施來提高橋面板與鋪裝層間的界面粘結強度和給橋面抗裂增韌。
  2. The consolidating wave speed means the speed at which elastic stress wave transmits throughout reinforced concrete, and it is intervenient the inherent wave speed of steel and of the concrete. moreover, the consolidating wave speed inherent in the material of the reinforcing steel bar and the concrete, and it relates to the cling strength of steel bar and the concrete

    固結波速是指彈性應力波通過鋼筋-混凝土體系傳播時的速度，通過理論分析得知固結波速的大小介於鋼筋和混凝土中彈性應力波速之間，由鋼筋與混凝土二者的材質特性決定，與二者的粘結強度密切相關。
  3. Particle boards - determination of internal bond of layers of extruded boards

    木屑板.擠壓板層間粘結強度測定
  4. Standard test method for adhesion strength and mechanical failure modes of ceramic coatings by quantitative single point scratch testing

    用定量單點劃痕試驗測定陶瓷塗層粘結強度和機械損壞類型的標準試驗方法
  5. Methods of test for screed materials - determination of bond strength

    找平層材料的試驗方法.粘結強度的測定
  6. Indirect methods to measure the interface bond strength include the interlaminar shear strength test.

    測量界面粘結強度的間接方法包括層間剪切強度試驗。
  7. In it ' s raw state, ls has very little adhesive strength

    在它的原始狀態，液體軟陶有一定的粘結強度。
  8. Standard of adhesive strength test of tapestry brick for building engineering

    建築工程飾面磚粘結強度檢驗標準
  9. Methods of test for ancillary components for masonry - determination of bond strength of prefabricated bed joint reinforcement in mortar joints

    圬工輔助砌塊的試驗方法.灰漿連接處預制基地接合處加固的粘結強度的測定
  10. 2. based on 123 specimens results of the shear bond test of frp and concrete, the failure characteristics of bond test are described, and the relationship of bond strength and bond slip is discussed

    通過123個混凝土試件與cfrp 、 gfrp片材的抗剪粘結強度試驗結果，分析frp片材與混凝土發生剪切粘結破壞的全過程以及破壞特徵，討論了粘結力與粘結滑移的關系。
  11. The section loss of steel bars and degradation of bond intensity were taken into consideration in this study in order to establish the finite element model of corroded reinforced concrete beam through simulating the bond slip behavior between steel bar and reinforced concrete based on nonlinear spring element

    摘要在考慮銹蝕引起的鋼筋橫截面損失和粘結強度下降的前提下，利用非線性彈簧單元模擬銹蝕鋼筋與混凝土之間的粘結滑移性能，建立了銹蝕鋼筋混凝土梁的有限元分析模型。
  12. Insert bond strength test procedure for electrical connectors

    電連接器插入粘結強度試驗程序
  13. Standard test methods for flexural bond strength of masonry

    磚石工程彎曲粘結強度的標準試驗方法
  14. Effect of interfacial agent on bond strength between new and old concrete

    界面劑對新老砼粘結強度的影響
  15. Optical coatings - part 1 : testing of the adhesion by storing in deionized water and in salt water

    光學薄膜.第1部分:脫離子水和鹽水中貯存粘結強度試驗
  16. Optical coatings - part 2 : testing of the adhesion by boiling in deionized water and in salt water

    光學薄膜.第2部分:脫離子水和鹽水中煮沸粘結強度試驗
  17. Standard test method for determining strength of gap - filling adhesive bonds in shear by compression loading

    測定裂縫強度的標準試驗方法.用壓力負荷法測定填充膠粘劑的剪切粘結強度
  18. Inorganically post - installed bars although have the ideal durability and heat - resistance, its bonding strength is low. it is unable effectively to transmit the load, the anchor depth is too big. these restricted application of the inorganic anchoring material in the post - installed fastening project

    無機植筋雖有較理想的耐久性能和耐高溫性，但其粘結強度較低，無法有效傳遞荷載應力，錨固深度太大，這制約了無機粘結材料在植筋工程中的應用。
  19. The main content is : splitting tensile experiments were carried out about the standardized cube bonding specimens ( 150x 150x 150mm3 ) of the new - old concrete after high temperature. the temperature is divided into 9 groups from normal atmospheric temperature to 900, the cooling styles are natural cooling and spraying water cooling ; different interfacial treating methods : brushed with steel - wire brush, man - made chiseling ( not evenly ), man - made chiseling ( quite evenly ) ; different interfacial agents : no interfacial agent, neat cement paste, cement paste mixed with 10 % expanding agent

    主要內容有：本文對75個高溫作用后的標準立方體新老混凝土粘結試件進行了劈拉試驗，溫度從常溫到900c分9個溫度段，降溫方式分自然冷卻和噴水冷卻兩種。著重考察了溫度、降溫方式、界面粗糙度及界面劑對新老混凝土粘結劈拉強度的影響規律，闡述了高溫后粘結強度下降的機理。
  20. Interface is the weakest region in new - to - old concretes or mortars. usually, the interfacial bond strength is very low, and approach to the strength of substrate

    界面是新老砂漿或新老混凝土中最薄弱的區域，通常情況下，界面粘結強度低，很少達到本體的相應強度。
分享友人
分享到 Line

分享到臉書