膠料性能 的英文怎麼說
中文拼音 [jiāoliàoxìngnéng]
膠料性能
英文
green properties-
The results of research on the workability of hbc concrete show that hbc concrete, when compared with opc concrete, has excellent compatibility with superplasticizer, in terms of better initial fluidity, less slump loss, definite saturation point and less dosage at saturation point. in addition, good mineral admixture such as i class fly ash can obviously improve the workability of hbc concrete. moreover, hbc concrete exhibits more excellent workability under the condition of low w / c ratio, which indicates hbc is more suitable for making super high strength concrete whose w / c ratio is very low
對高貝利特水泥高性能混凝土工作性能的研究結果表明，高貝利特水泥與高效減水劑具有良好的適應性，表現為初始流動度較大，經時損失較小，具有明顯的飽和點且飽和點摻量較小；此外，優質的礦物摻和料如一級粉煤灰能明顯改善hbc混凝土的工作性能；更為突出的是hbc混凝土在低水膠比的情況下表現出更為優異的工作性，這一特性預示著高貝利特水泥更適宜配製水膠比很低的超高強混凝土。The research results show that, from the viewpoint of second phase morphologies, there exist quite differences between the grain - type materials ( such as wc / bcu brazing deposit material, wrs1000 and 1zt tungsten carbide strengthening overlaying material, as well as the wear - resistant material of polymer adhesive coating etc. ), and the aggregation - type as well as dispersion - type ones ( such as zg35simn, wrd - 1 and khc - k2 depositing material ) in the wear - resistance and sand slurry abrasion mechanism. the sand slurry abrasion mechanisms are brought forward, of new wear - resistant materials with the features of grain - type second phase morphologies
研究發現，與聚合型、彌散型第二相的材料（如zg35simn 、 wrd ? 1和khc ? k2熔敷材料等）相比，顆粒型第二相的材料（如wc bcu釬焊熔敷耐磨材料、 wrs1000型耐磨材料、 1zt碳化鎢顆粒增強熔敷材料及ktc ? 1耐磨膠粘塗層材料等）在耐磨性能和磨損機理等方面均有不同，總結提出了以「顆粒型第二相」為特徵的耐磨新材料泥沙磨損機理。Methods of testing plastics - chemical properties - determination of butyl rubber content of low density polyethylene compounds
塑料的試驗方法.化學性能.低密度聚乙烯化合物中丁基橡膠含量的測定Cellular rubber and plastics - determination of dynamic cushioning performance
泡沫橡膠和塑料.動態減震性能的測定The present work indicates the organic nf membranes and the inorganic nf membranes all have shortages, so develop composite nf membranes that have low cost, mechanically strong and thermally / chemically - resistant, easy to cleanout and good performances is a very important task. in this paper, the preparation of inorganic - organic composite nf membranes were presented. this composite comprise a porous sio2 / al2o3 support substrate, the pore diameters of which ranging from 10 to 15 nm, this inorganic support substrate having a polymer membrane which comprises an polyvinyl alcohol ( pva ) or polyamide ( pa ) densely deposited on at least one of the face surfaces thereof, the structural porosity of such pva and pa membrane ranging from 3 to 5 nm
本論文以開發無機?有機復合納濾膜為出發點，首先在al _ 2o _ 3多孔微濾膜上利用溶膠?凝膠法制備sio _ 2 al _ 2o _ 3無機復合超濾膜作為無機?有機復合納濾膜的基膜；選用聚乙烯醇和聚酰胺為表面功能層材料，分別探討了以羥基丁二酸和磺基水楊酸為混合交聯劑，採用浸塗法制備了聚乙烯醇sio _ 2 ? al _ 2o _ 3復合納濾膜；以均苯二甲酰氯、哌嗪和二胺為單體，採用界面聚合法制備了聚酰胺sio _ 2 ? al _ 2o _ 3復合納濾膜，並對影響膜性能的諸多因素進行系統研究。The small packing adhesive, which is a modified product from ethylene - vinyl acetate copolymerized emulsion, has high solid content, low viscosity, and good adhesive strength. the product is up to the standard of foodstuff hygiene and suitable for the small package of the cigarette packing production line with stable adhesive application and the making speed up to 400 packs per minute. type i is for white card paper, while type ii is for golden card paper
小盒包裝膠系乙烯-醋酸乙烯共聚乳液改性產品，具有高固含低粘度粘接力強等特點，產品符合食品衛生標準，適用於卷煙卷包生產線的小盒包裝，施膠穩定，無開包等不良現象，車速可達400包分，型為白卡紙專用膠，型為金卡紙專用膠，具有極佳的初粘力和持粘力，對非極性材料的光滑表面有獨特的優良粘接性能，對各種難粘材料均可適用。Sepiolite has low shrinking rate, plasticity is good, alkali - resisting and easy to dissolve, absorb the peculiar industry performance such as being strong of performance, in addition, also absorb, decolouring, hot stability is anticorrosive, resist radiation and insulate against heat, the characteristic such as being insulating, is used in the non - asbestos jointing sheet, various of brake shoes, paint, sound insulation of the building mainly, thermal insulator
海泡石具有收縮率低，可塑性好，耐堿易溶解，吸附性能強等特有的工業性能，除此之外，還具有吸附，脫色，熱穩定，抗腐蝕，抗輻射及隔熱，絕緣等特性，主要用於密封產品如非石棉橡膠板，摩擦產品如各式剎車片，油漆、塗料，建築隔音、隔熱材料。Sepiolite has low shrinking rate, plasticity is good, alkali - resisting and easy to dissole, absorb the peculiar industry performance such as being strong of performance, in addition, also absorb, decolouring, hot stability is anticorrosie, resist radiation and insulate against heat, the characteristic such as being insulating, is used in the non - asbestos jointing sheet, arious of brake shoes, paint, sound insulation of the building mainly, thermal insulator
海泡石具有收縮率低，可塑性好，耐堿易溶解，吸附性能強等特有的工業性能，除此之外，還具有吸附，脫色，熱穩定，抗腐蝕，抗輻射及隔熱，絕緣等特性，主要用於密封產品如非石棉橡膠板，摩擦產品如各式剎車片，油漆、塗料，建築隔音、隔熱材料。The results of performance testing showed that the additive of nano - powders can evidently enhance the latex coatings " weathering resistance, scratch resistance, water resistance and alkaline resistance, and do not reduce other performances ; polybasic nano - composite powders have more efficient than single nano - powder ; the dispersing method have biggish effect on performances. observing the stability of nano - additive of exterior latex coating showed there was no viscidity rising, no delaminatiom sedimentation in two months. tryout by plant showed that nano - weatherability additive can obviously enhance the weathering resistance of latex coating and water resistance, and no reducing other capabilities
對其性能研究的結果表明，納米粉體材料的引入，可以明顯提高乳膠漆的耐候性、耐洗刷性和耐水耐堿性能，對其它性能無不良影響；納米多元復合粉體比單一粉體的改性效果明顯；納米粉體的添加工藝對改性乳膠漆性能有較大的影響，採用同普通填料一致的添加方式制備的試樣與採用超聲波預分散后在配漆階段加入制備的試樣相比，後者在穩定性、耐候性等方面的性能都有所提高。Their properties have been investigated by using scanning electronic microscopy ( sem ), differential scanning calorimetry ( dsc ), x - ray diffraction ( xrd ), thermogravimetry - differential thermal analysis ( tg - dta ), infrared spectroscopic analysis ( ir ), and gas chromatography ( gc ), etc. the effects of the mulser ' s stirring rate and the emulsifier concentration on the properties of encapsulated pcms have been systematically studied, and nanopcms have been obtained by increasing the stirring rate or the emulsifier concentration. the influences of different nucleating agents on micropcm performances have also been investigated in detail to search for a suitable nucleating agent to prevent micropcms from super - cooling
首先，系統研究了乳化機轉速和乳化劑濃度對膠囊性能的影響，並通過提高轉速或乳化劑濃度獲得相變材料納膠囊；其次，系統研究了不同成核劑對微膠囊性能的影響，找到合適的成核劑抑制了相變材料微膠囊的過冷現象；再次，詳細研究了環己烷對膠囊性能的影響，並通過添加適量環己烷提高了相變材料微膠囊及納膠囊的耐熱溫度。Gray system study on the influence of particle size distribution of slag powder on performance of cementitious materials
礦渣微粉顆粒分佈對膠凝材料性能影響的灰色系統An experiment was conducted to study the effects of hot - pressing temperature on properties of wheat straw - plastic composites made from wheat straw and recycled polyethylene ( pe ) using isocyanate as adhesive through multi - factor orthogonal experiment and single - factor experiment
摘要通過正交試驗和單因子試驗，以麥秸和廢舊聚乙烯塑料為原料，使用異氰酸酯膠黏劑壓制麥秸塑料刨花板，分析熱壓溫度對麥秸聚乙烯復合材料性能的影響。Experimental study of performance of coal gangue as cementing filling aggregate
煤矸石作為膠結充填骨料性能的實驗研究Test research on performances of phosphorous gypsum as aggregate for cementation filling
磷石膏作為膠結充填骨料性能的試驗研究The accreditation / licensing because of the size, shape, materials properties, processing, printing and the number of different ways, so it does not seem as traditional offset printing price fixed formula, the same kind of material, the same number of words, or the price difference, therefore, the price should be accurate by the material, the number of machining and other factors, such as the combination of calculated
由於采訪證/工牌因其尺寸規格、形狀、材料性能、加工工藝、印刷方式及數量等不同，所以它並不像傳統膠印那樣有固定的印刷報價公式，同種材料，同種數量的話，也還是有價格差異的，所以，精確的價格應該是由材料、數量、加工工藝等因素等結合而計算出來的。The load characteristic and the property of skeleton material for tire and adhesive property between rubber and skeleton materials were reviewed in this paper
摘要本文對橡膠基復合材料輪胎用增強骨架材料的負荷特點、骨架材料性能、橡膠與骨架材料的粘合特性進行了分析。Activity factor is presented for evaluating cementirous property of mineral additives by certain derivation and numerical analysis
通過一定的推導與數值分析，提出了用活性因子評價礦物摻合料膠凝性能的方法。Effect law of different materials on the properties of structural adhesive were studied and the modifying mechanism was discussed by microcosmic testing method. results showed that, when nanosize sio _ 2 dispersed in the epoxy base, effect of nanosize sio _ 2 on working performance was changed obviously, on bond strength, impact strength and heat distortion property were good
論文通過納米二氧化硅、納米碳酸鈣和有機蒙脫土三種納米材料對常用的環氧樹脂建築結構膠進行改性，研究了不同納米材料對結構膠的性能的影響規律並通過微觀測試手段對其改性機理進行了探討。There are still knowledge gaps between fabrication and properties of nano - and microencapsulated phase change materials. the present research has investigated improving their thermal stability and preventing them from super - cooling in order to fabricate micropcms and nanopcms with higher performances. micropcms and nanopcms were synthesized by encapsulating n - octadecane and the other components within the melamine - formaldehyde ( abbr
本項研究以三聚氰胺樹脂為囊壁，正十八烷為囊芯，通過原位聚合法制備相變材料微膠囊以及納膠囊，並通過sem 、 dsc 、 tg - dta 、 xrd 、 ftir 、 gc等分析測試手段對這些膠囊性能進行了系統研究和分析。But the surface characteristics is minor. when rigidity of granulated crumb rubber is increased, the performance of mixture is improved including compaction performance, volume performance and enduring performance. the ratio of coarse aggregates, granulated crumb rubber and coarse granulated crumb rubber are confirmed using the central composite design and response surface methodology
研究結果表明，橡膠顆粒的形狀特性和力學特性對混合料的性能影響較大，隨細長扁平顆粒含量的減小，硬度的增大，混合料的壓實特性、體積特性和使用的耐久性增強;橡膠顆粒的表面特性的差異對混合料性能有一定影響，但其影響並不顯著。分享友人