蒸汽負荷 的英文怎麼說

中文拼音 [zhēngqìfùhé]
蒸汽負荷 英文
steam load
  • 蒸 : Ⅰ動詞1. （蒸發） evaporate2. （利用水蒸氣的熱力使食物熟或熱） steam Ⅱ名詞[中醫] （將藥物隔水蒸熟） steaming
  • 汽 : 名詞1. （由液體或某些固體變成的氣體） vapour2. （水蒸氣） steam
  • 負 : Ⅰ名詞1 （負擔） burden; load 2 （虧損） loss 3 （失敗） defeat Ⅱ動詞1 [書面語] （背） carry on th...
  • 荷 : 荷名詞（蓮） lotus
  • 蒸汽 : vapour; reek; breath; steam蒸汽採暖 steam heating; 蒸汽錘 [機械工程] steam hammer; 蒸汽打樁鍾 ste...
  • 負荷 : [電學] load; charge; weight
  1. Boiler is the heat equipment in common use best of all, which can supply qualified steam for the requirement of steam quantity adapting to burthen

    鍋爐是最常用的熱工設備，其要求是供給合格的蒸汽，使鍋爐產汽量適應負荷的需要。
  2. Presents the steady - state programming with constant coolant average temperature and constant live steam pressure, an ideal programming for marine nuclear power plant ( npp ), under which, both the coolant average temperature and the live steam pressure of nuclear steam supply system ( nsss ) are constant when the steady state operating condition is varied, and points out that in comparison with the steadysate programming with constant coolant average temperature, the ideal programming can improve the overall operating performance of npp effectively, especially in low - load range, for instance, raise the heat efficiency of npp, decrease the operating noise of main coolant pump, and improve the conditions of design, operation and control of the secondary loop system

    雙恆定運行方案是船用壓水堆核動力裝置的理想運行方案.在這種運行方案下，當裝置穩態功率變化時，冷卻劑平均溫度與蒸汽壓都保持不變，與通常採用的冷卻劑平均溫度恆定運行方案相比，有效地改善了核動力裝置的總體運行性能，特別是在低負荷運行時，可以提高裝置經濟性、降低主泵運行噪聲、改善二迴路系統的設計、運行和控制條件，這對于提高船用核動力裝置的運行可靠性和安全性具有實際意義
  3. When allowance is made for the separate auxiliary load the consumption can rise to nearly 1 ib / shp hour and this is generally about 20 % better than the overall fuel consumption of a steam plant at cruising speed

    當考慮分開的輔機負荷時，其耗油率幾乎能增加到1磅/軸馬力小時，一般來說比蒸汽裝置的巡航總油耗大約多20 % 。
  4. The # 9 and # 10 142mw heat supply units in gansu xigu power plant, the steam extraction main pipe system adopt westation control system of westing house company and deb coordination control policy in design. the coordination control policy successfully expand the whole the running range, from the normal running condition to abnormity running condition and start or stop condition, which simplicity base on burthen and main steam pressure coordination control

    甘肅西固熱電廠# 9 、 # 10142mw抽汽母管制供熱機組，選用美國西屋公司westation控制系統，設計、應用了deb協調控制策略，從單純作為負荷和主蒸汽壓力控制協調的基本功能，成功擴展到整個運行范圍，即從正常運行工況到異常運行工況及啟、停工況。
  5. In the whole system, the inner leak system is occurred to the lower pressure bypass system, this will directly cause the high quality reheated steam to reach to condenser, meanwhile increase the heat load of condenser, and the economy benefit of the unit will decreased

    整個系統存在的內漏主要是低壓旁路低壓旁路的泄漏，直接造成了高品質的再熱蒸汽短路到凝汽器，同時增加了凝汽器的熱負荷，對機組經濟性的影響較大。
  6. The response was compared with that obtained through simulation realized by the use of matlab and the actual process on different steam flow, feed water flow, fuel flow and control method

    並運用matlab模擬工具，針對鍋爐水位和汽壓調節對象模擬模型在不同的蒸汽負荷、不同給水量、不同燃油量和不同控制方式下的動、靜態情況進行模擬研究。
  7. According to the thermodynamics theory of vapor compression refrigeration cycle, hfc - r134a is chosen as refrigerant fluid and the thermodynamics calculation of refrigeration system is accomplished, which is based on the table of r134a thermodynamics characteristics and estimate of portable refrigerator ' s calorific burthen

    本文根據蒸汽壓縮式製冷循環的熱力學原理，從小冷量、小體積的便攜式冷藏箱的熱負荷計算出發，以所選用製冷劑（ r134a ）的熱力性質表為依據，進行了製冷系統的基本熱力計算。
  8. With fast development of our country " s gas industry and air ' s increasingly serious contamination in city, using gas instead of coal and supplying energy in high efficiency and cleanliness has become necessary way in city. there are different problems in the current heating ( air conditioning ) systems. in the cogeneration system, heat and power affect each other, heating - pump heating ( aie conditioning ) system can not satisfy the peak load very well, the cost of gas fuel in boilor heating sestem is so high. the high generating efficiency of the diesel - engine two - sourse heating ( air conditioning ) systems is limited in range of 100kw - 1000kw, the heating scope is so limited. combined cycle of two sourse heating ( air conditioning ) system is most suitable selection to buesness community with big scope my paper aim at this syetem ' s primary question when it is applied in our country - - - - bringing project into execution and technology economy feasibility and off - design performence, combined with a certain demonstrating project in beijing buesness community, going along with calculating and analyzing, drawing out some efficient datas and conclusions, based on this, bringing out primary alements affecting combined cycle of two sourse heating ( air conditioning ) system " economics

    熱電聯產系統熱電相互牽連，熱泵供暖（空調）系統不容易很好地滿足尖峰負荷，鍋爐供暖系統供熱中天然氣燃料構成的成本過高，內燃機雙源供暖（空調）系統的高發電效率僅限於100kw - 1000kw負荷范圍，供熱面積有限。對于大面積的商業園區、居民小區，燃燒天然氣的燃氣-蒸汽聯合循環雙源供暖（空調）系統是最佳選擇之一。本論文針對該系統在我國應用時的主要問題- - -方案的技術實施與技術經濟可行性，結合北京某一商業園區示範工程，進行了系統的計算與分析，得到了有效的數據與結論，在此基礎上，提出影響聯合循環雙源供暖（空調）系統經濟性的主要因素，並進行敏感性分析，得出有益的結論；最後通過各種供暖方案的比較分析回答了某些人對該系統的疑慮和不解，並指出系統的優化方向。
  9. The accurate models of steam pressure controlled system were established in accord with the theory of marine boiler. the response was compared with that obtained through simulation realized by the use of matlab and actual process on different steam flow, fuel flow and control method

    運用matlab模擬工具，對汽壓調節對象模擬模型在不同的蒸汽負荷、不同燃油量和不同控制方式下的動、靜態情況進行模擬比較，提出不同控制要求下的控制演算法。
  10. In the systematic optimization we have the gradational optimization, when the heat and electricity load is acknowledged, we can have the least vapour by optimizing the arrangement of the load of every generator in advance. then we can optimize the load of every boiler in the light of the total vapour and have the least fuel consumption

    在系統優化方面採用了分級優化方法：當外界所需的熱、電負荷確定以後，首先優化分配各臺汽輪機的熱、電負荷使得所需的總新蒸汽量最低；然後根據這一總新蒸汽負荷優化分配各臺鍋爐的負荷，使總燃料消耗量最低。
  11. The simulating result showed that when the unit load changes, the maximum dynamic difference of main - steam temperature drops 13. 8 %, the regulating time shortens 17 % and the control character is improved well

    模擬結果表明，在機組發生負荷擾動時，主蒸汽溫度的最大動態偏差降低了13 . 8 % ，調節時間縮短了17 % ，其調節品質明顯改善。
  12. The original design was intermediate vapor 42t / h, but the actual output is 30 - 35t / h, at the same time the temperature and pressure of the vapor are unstable, it affects the economic efficiency, the reason were the collecting dust on the heat area and serious corrision, they led to the decrease of the boiler load, and need stop to washing the dust, the article deals with the reform of the exhaust gas boiler, at the basic of the design condition, after thermo calculation, flute gas, resistence calculationand strenth calculation, the structure of the heat surface had been rearranged, then the proof calculation was done

    原設計產中壓蒸汽42噸時，但投運后只產30 - 35噸時，並且蒸汽溫度和壓力均不穩定，影響到經濟效益。其原因是受熱面積灰和腐蝕嚴重，影響傳熱使鍋爐負荷下降，不能長時間運行，需停產清理積灰。本論文針對此余熱鍋爐的技術改造，在給定設計條件基礎上，通過熱力計算，煙氣阻力計算和強度計算，對鍋爐受熱面結構重新布置，然後再作校核計算。
  13. Stability of main steam pressure is the foundation of the key parameter stability ( include the main steam temperature, the vapor pack water level, the oxygen content in the smoke etc. ) in the units, deb system increase the dependability and the economy greatly with the settlement of the energy ' s equilibrium between the boiler and the steamer

    本機組利用先進的硬體設備dcs和優化的控制策略deb ，圓滿解決了機組協調控制系統中主汽壓力穩定性及負荷適應性這一主要矛盾。主蒸汽壓力穩定是機組一切關鍵參數（包括主蒸汽溫度、汽包水位、煙氣含氧量等）穩定的基礎， deb系統解決了機組鍋爐和汽輪機之間能量平衡，使機組可靠性和經濟性大大提高。
  14. This article emphatically discussed and analyzed following points : load command feed forward function can improve the rapid respond character of steam turbine generator ; lead of load command have advance control function on boiler main control and can highly improve the stability of main steam pressure ; the use of predict control and state space variable function can improve the quality of boiler steam temperature control effectively, control the steam temperature in the defined range and increase the boiler and turbine life and efficiency even if working state changed in a big range ; linear compensation can restrain the vibration of generator load in the condition of big loa d change

    本文重點討論、分析提出負荷指令前饋作用可以提高汽輪發電機快速響應特性；負荷指令的導前功能對鍋爐主控有超前控製作用，能顯著提高主蒸汽壓力的穩定性；採用預測及狀態空間法能有效改進鍋爐蒸汽溫度控製品質，在大幅度工況變化下仍有效控制蒸汽溫度在額定范圍內，提高鍋爐、汽輪機壽命及其效率；汽輪發電機組的快速響應性與汽輪發電機組負荷振蕩問題間的平衡關系，採用線性補償可以有效抑制在負荷變化梯度較大情況下發電機負荷振蕩問題。
  15. For this, some measures have been put forward, including : strictly controlling metal temperature of turbine and boiler parts ; blowing out with steam ; suitably enhancing the speed of increasing or decreasing the load of unit ; carrying out aimed detection by using oxide skin detecting technology etc., to ensure the safety of operation

    對此提出了嚴格控制蒸汽和鍋爐部件金屬溫度及嚴格進行蒸汽沖洗，適當提高機組升降負荷速度，並利用氧化皮檢測技術進行針對性檢測等措施，保證鍋爐運行安全。
  16. The numerical results show that because of the temperature variation of cooling water along its flow direction the heat load of the second - pass tube bundle is lower than that of the first - pass tube bundle, which brings about the steam flow deflection and then the deterioration of heat transfer

    計算結果表明，由於冷卻水溫度沿冷卻水流動方向的變化，第二流程管束的熱負荷明顯小於第一流程的，並使蒸汽流動?生側向偏斜，導致流動與傳熱特性的惡化。
  17. Supplies steam for industrial process where load swings are common or higher quality steam for base loading of a turbine / generator for the production of electricity

    產生的蒸汽是用於負荷常變的普通工業過程還是用於要求蒸汽品質高的帶基本負荷的汽輪發電機組。
分享友人
分享到 Line

分享到臉書