試驗焊接 的英文怎麼說
中文拼音 [shìyànhànjiē]
試驗焊接
英文
trial weld- 試 : 名詞(古代占卜用的器具) astrolabe
- 驗 : 動詞1. (察看; 查考) examine; check; test 2. (產生預期的效果) prove effective; produce the expected result
- 焊 : 動詞(用熔化的金屬修補金屬器物或使金屬工件連接起來) weld; solder
- 接 : Ⅰ動詞1 (靠近;接觸) come into contact with; come close to 2 (連接; 使連接) connect; join; put ...
- 試驗 : trial; experiment; test
- 焊接 : weld; welding; soldering; seal; sealing; sealing-in; shutting together
-
The welding performance of homemade wear - resistant cast steel has been studied base on the weldability tests, the repair welding procedures of wean - resistant cast steel ( abrasion - plates ) have been made up, the results show that satisfying repair welding quality can be attained with such welding conditions as the low hydrogenous alkalescent welding rod, preheating and slow cooling, strictly maintaining the interbedded temperature of 250 ~ 300 and controlling welding technique
通過對其焊接性能的試驗研究,制定了該類鑄鋼件(磨耗板)的補焊工藝:低氫型堿性焊條,預熱與緩冷相結合的工藝措施,嚴格控制層間溫度( 250 ~ 300 )及焊接工藝規范,可獲得滿意的修復質量。Methods of the strength tests for brazed and soldered joint
釬焊接頭強度試驗方法Methods of bend test for butt welded joint
對接焊接頭的彎曲試驗方法Methods of bend and compression tests for welded joint
焊接接頭彎曲及壓扁試驗方法Differential pressure testing method of titanium welded tubes
鈦焊接管的分壓試驗方法Method of fillet weld test for welding consumables
焊接消耗品用角焊試驗的方法Backing weld procedure technique of all - position narrow gap and thick - walled pipe welding is developed about all - position single - pass welding section analysis, wire feeding behavior, weld arc length, welding current analysis, procedure and joint test. the achievement has general guide meaning to producing and testing all - position welder
從單焊道全位置區段、送絲行為、焊接弧長(電壓) 、電流行為分析、工藝試驗和接頭檢驗等幾方面介紹管道全位置打底焊工藝特點,其研究成果對全位置焊接機的製造和調試具有普遍指導意義。Abstract : backing weld procedure technique of all - position narrow gap and thick - walled pipe welding is developed about all - position single - pass welding section analysis, wire feeding behavior, weld arc length, welding current analysis, procedure and joint test. the achievement has general guide meaning to producing and testing all - position welder
文摘:從單焊道全位置區段、送絲行為、焊接弧長(電壓) 、電流行為分析、工藝試驗和接頭檢驗等幾方面介紹管道全位置打底焊工藝特點,其研究成果對全位置焊接機的製造和調試具有普遍指導意義。Destructive tests on welds in metallic materials - cold cracking tests for weldments - arc welding processes - general
金屬材料中焊接的有損檢驗.焊接的冷裂試驗.弧焊工藝.總則Destructive tests on welds in metallic materials - cold cracking tests for weldments - arc welding processes - self - restraint tests
金屬材料焊接的有損試驗.焊接的冷裂試驗.弧焊工藝.自束試驗Destructive tests on welds in metallic materials - cold cracking tests for weldments - arc welding processes - externally loaded tests
金屬材料焊接的有損檢驗.焊接的冷裂試驗.弧焊工藝.外部載荷試驗Destructive tests on welds in metallic materials - hot cracking tests for weldments - arc welding processes - general
金屬材料焊接的有損試驗.焊件的熱裂試驗.弧焊過程.概要Destructive tests on welds in metallic materials - hot cracking tests for weldments - arc welding processes - self - restraint tests
金屬材料焊接的有損試驗.焊接的熱裂試驗.弧焊工藝.自束試驗Destructive tests on welds in metallic materials - hot cracking tests for weldments - arc welding processes - part 1 : general
金屬材料焊接的有損試驗.焊接的熱裂試驗.弧焊工藝.第1部分:總則Destructive tests on welds in metallic materials - hot cracking tests for weldments - arc welding processes - part 2 : self - restraint tests
金屬材料焊接的有損試驗.焊接的熱裂試驗.弧焊工藝.第2部分:自束試驗Welding procedure qualification based on tested welding consumables
基於試驗焊接材料的工藝評定Destructive test on welds in metallic materials - macroscopic and microscopic examination of welds
金屬材料焊接點的破壞試驗.焊接點的宏觀和微觀檢驗Specification and qualification of welding procedures for metallic materials - qualification based on tested welding consumables
金屬材料焊接程序規范和合格鑒定.基於試驗焊接消耗品的合格鑒定Abstract : by taking the modification project of hydrogen generation unit in a petrochemical plant as an example, the successful welding of heat - resistance ferroalloy with high cr - ni content is presented, including weldability analysis, weld procedure qualification test, weld process measures and quality inspection
文摘:以制氫裝置改造工程為例,報道在制氫轉化爐爐管現場焊接施工中,對鐵基高鉻鎳耐熱合金管材的成功焊接,包括可焊性分析、焊接工藝評定試驗、焊接工藝措施和質量檢驗。Destructive tests on welds in metallic materials - hot cracking tests for weldments - arc welding processes - part 2 : self - restraint tests iso 17641 - 2 : 2005 ; german version en iso 17641 - 2 : 2005
金屬材料焊接的有損試驗.焊接的熱裂試驗.弧焊工藝.第分享友人