調整柄 的英文怎麼說

中文拼音 [diàozhěngbǐng]
調整柄 英文
adjusting handle
  • 調 : Ⅰ動詞1 （配合得均勻合適） harmonize; suit well; fit in perfectly 2 （使配合得均勻合適） mix; adju...
  • 整 : Ⅰ形容詞1 （全部在內; 完整） whole; all; complete 2 （整齊） neat; tidy; orderly Ⅱ動詞1 （整理; 整...
  • 柄 : Ⅰ名詞1 （器物的把兒） handle 2 （植物的花、葉或果實跟莖或枝連接部分） stem 3 （言行上被人抓住的材...
  • 調整 : adjust; tune up; trim; trimming; variation; modulation; arrangement; debug; rectification; redres...
  1. Chain adjusters and crank cotter pins for bicycles

    自行車鏈調整器和曲柄扁銷
  2. Styles, including dotted or solid lines ; hatched border, inside or outside the rectangle ; and resize handles, inside or outside the rectangle

    樣式，包括虛線或實線；陰影框，在邊框內或邊框外；和大小調整手柄，在邊框內或在邊框外。
  3. The regulating handle is fitted with a fine speed adjust knob and a latch

    調節手柄配有一個細的速度調整旋扭一個鎖銷。
  4. How to adjust the gap between the upper and lower blades. loss the screw first, then turn the handle to what you need, then fasten the screw again

    間隙調整時需將鎖緊螺釘松開，然後轉動手柄至所需的刻度值，再將鎖緊螺釘鎖緊。
  5. Control and grab the lower - right sizing handle

    控制項並抓住右下角大小調整手柄。
  6. Button and observe the resize handles

    選擇say hello按鈕並觀察大小調整柄。
  7. Button, and notice that it does not have resize handles

    選擇私有的say goodbye按鈕，請注意它沒有大小調整柄。
  8. Converts a point in a handle s coordinate system to the adorner window coordinates

    將調整柄的坐標系統中的點轉換為裝飾器窗口坐標。
  9. Adjustable adaptors for tools with morse taper shanks, long types

    帶莫氏錐柄刀具的可調整轉接器.長型
  10. Height adjustable handle for use in different positions

    手柄角度可隨您身高及使用習慣任意調整高度。
  11. Adjustable adaptors for tools with morse taper shanks, short types

    帶莫氏錐柄刀具的可調整轉接器.短型
  12. Start turn on the electric switch of the gasoline engine, quickly pull the rebound starting handle, start the engine by using the rebound starter, adjust the speed of engine well

    開機打開汽油機電門開關，快速拉動啟動繩手柄，利用反彈式啟動器啟動汽油機，調整好汽油機怠速。
  13. Collets with 8 o setting angle for tool shanks - collets, nuts and fitting dimensions

    刀具柄用帶8調整角的夾頭.夾頭螺母和配合尺寸
  14. Collets with 8 setting angle for tool shanks - collets, nuts and fitting dimensions iso 15488 : 2003

    刀具柄用8調整角的夾頭.夾頭螺母和配合尺寸
  15. Battery and charger, bulk waste flap, fold - down push handle, operating hour meter, patented filter shaker system, roller brush, justierbar, side brush, anhebbar / justierbar, state - of - charge indicator

    浮動式邊刷，可調整式主刷，可折疊式手柄，大垃圾擋板，操作計時器，吸入風扇切斷裝置，專利保護過濾器除塵系統，移動式塵箱，操作計時器，蓄電池，充電器，充電指示裝置。
  16. The optimization design of the crank - connect rod mechanism was carried out. collocating the mass reasonably, adjusting the ratio ( ( 1 - f ) / f ) of the long axis to the short axis of the ellipse track, adjusting the direction of long axis to the direction where the internal - combustion engine was not sensitive to the stimulating force. all the above contribute to the max reduction of the vibration

    對單缸內燃機的曲柄滑塊機構進行優化設計，合理的布置加配質量的大小和方向，對軌跡橢圓的長短軸比率（ 1 - f ） / f進行調整，將長軸方向調整到內燃機對激振力不敏感的方向，從而使不平衡力對內燃機所產生的振動最小，以某一具體的單缸內燃機為例進行了計算分析。
  17. Comfortable and easy to use, the strap has a handle with an adjustable buckle at each end. machine washable

    舒適和容易使用，皮帶有把柄與一個可調整的扣在各個末端。機器耐洗。
  18. You can move an ole item by dragging it ; you can resize a selected ole item by using the resize handles

    可以通過拖動ole項來移動它；可以通過使用調整大小手柄來調整選定ole項的大小。
  19. The sizing grip is always shown on the form

    大小調整手柄始終顯示在窗體上。
  20. The sizing grip is automatically displayed when needed

    需要時會自動顯示大小調整手柄。
分享友人
分享到 Line

分享到臉書