調節齒輪 的英文怎麼說

中文拼音 [diàojiéchǐlún]
調節齒輪 英文
adjust gear
  • 調 : Ⅰ動詞1 （配合得均勻合適） harmonize; suit well; fit in perfectly 2 （使配合得均勻合適） mix; adju...
  • 節 : 節構詞成分。
  • 齒 : Ⅰ名詞1 （牙; 牙齒） tooth 2 （物體上齒形的部分） a tooth like part of anything 3 [書面語] （年齡...
  • 輪 : Ⅰ名1 （輪子） wheel 2 （像輪子的東西） wheel like object; ring; disc 3 （輪船） steamer; steamboa...
  • 調節 : regulate; adjust; monitor; measure; take care of; condition; regulation; adjustment; conditioning...
  • 齒輪 : gear [rack; toothed] wheel; （toothed） gear; wheel gear
  1. It is provided with worm - gear box regulation to have a more accurate depth of paper press. the blade part is driven by independent gear and adjusted by ratchet wrench. it is also equipped with ruler to shorten the time required for blade adjustment

    採用蝸輪箱調節，使壓線深度更加準確，刀頭部分使用單獨齒輪傳動，利用棘輪板手調動，並帶有長尺，使調刀時間縮短。
  2. Automatic yarn let - off system which used change gear drive for regulating run - in values

    採用交換齒輪調節送經量的積極式送經機構。
  3. A gear pump is installed on the production line, the pressure is stabilized by varying the speed of extruder through the help of computer according to the accurately measured pre - pump pressure, resulting optimized material feeding process

    在擠出生產線上安裝一臺齒輪泵，通過在泵前準確的測壓，通過微機處理調節擠出機速度，保持壓力穩定，有序提供料流來優化供料過程。
  4. Active yaw control, first incorporated into the evo iv, was developed by mitsubishi to improve a vehicle ' s cornering and acceleration performance, and consequently its safety, under a wide range of operating conditions

    主要結構是裝在後輪半軸間的濕式多版差速器，最裡面的一組減速齒輪調節左右輪驅動力分佈。
  5. In the design, gear and spline were adopted, so symmetrical movement of ( collimator ’ s ) lead gates can be achieved easily, mechanical structure became more compact. worm was adopted to adjust mirrors accurately, and deflection of mirrors can be prevented in case of the external impacts or vibrations

    採用齒輪齒條結構，實現鉛門的對稱開合運動，使子系統的機械結構更為緊湊，同時提高了定位精度;採用蝸輪蝸桿調解反光鏡的角度，可以使反光鏡的調節更精確，同時可以防止在外界振動或撞擊下反光鏡發生偏轉。
  6. The hand wheel is linked to the front roll via heavy - duty gears so that the nip - gap can be easily adjusted even while running a heavy compound

    手輪通過高堅固的齒輪連接到前輥，即便是開煉大量橡膠也可以輕松調節。
  7. 2, the friction coefficient at the pitch point is not a monotonic quantity of the rational speed or the load, instead of having a maximum value. and the value of the friction coefficient is very small, its order of magnitude only being 10 - 3. so, it is reasonable that the friction force on teeth surfaces are ignored when the gear - driven contact fatigue strength is designed

    2 、當輪齒在節點嚙合時，隨著轉速或載荷的變化，齒面摩擦系數並非呈單調變化，而是存在極值點;節點嚙合處的齒面摩擦系數很小，其數量級為10一， ，因此在做齒輪強度設計時，忽略齒面摩擦力的影響是有理論根據的。
  8. In tradition, worker must computer, then change the gear for regulating the quantity of seeding by himself. this system can regulate it automatically by a microcomputer inside after inputting the demand of seeding quantity, and the regulating precision improved

    此系統與傳統播種機人工計算、更換齒輪調整播量的方法不同，而是利用單片機可編程的優點，在播種前輸入播量、排種器類型及五輪儀打滑移率等參數，系統內部會自動進行計算調整，提高了調節精度。
  9. The babbitt adjustable sprocket rim will provide for remote operation of butterfly valves in high, normally out - of - reach locations

    巴比特合金可調節鏈輪齒輪圈，可用於位於高處，通常難于接近的蝶閥的遠程操作。
分享友人
分享到 Line

分享到臉書