超塑性學 的英文怎麼說

中文拼音 [chāoxìngxué]
超塑性學 英文
superplasticity
  • : Ⅰ動詞1 (越過; 高出) exceed; surpass; overtake 2 (在某個范圍以外; 不受限制) transcend; go beyo...
  • : 動詞(塑造) model; mould
  • : Ⅰ名詞1 (性格) nature; character; disposition 2 (性能; 性質) property; quality 3 (性別) sex ...
  • : Ⅰ動詞1 (學習) study; learn 2 (模仿) imitate; mimic Ⅱ名詞1 (學問) learning; knowledge 2 (學...
  1. Several questions about the compatibility of superplasticizer with cement for ready - mixed concrete are discussed from the standpoint of cement chemistry

    從水泥化角度討論了預拌混凝土用的水泥與化劑相適應的幾個問題。
  2. The test result of the rene95 sample showed that the maximum ultimate tensile strength can be as high as 1400mpa and has reached 97. 9 % of that of the sample fabricated by powder metallurgy ( pm ). the plastic elongation of the test sample can even exceed that of pm. the ultimate tensile strength of the test sample grown from single crystal substrate has surpassed 6 % of that of grown from the stainless steel substrate, at the same time the plastic elongation surpassed 40 %

    對成形試樣的力能測試結果表明,強度方面_ b最大為1400mpa ,已經達到了粉末冶金的97 . 9 ,方面甚至過了粉末冶金的水平;以單晶為基材的成形試樣其最大拉伸強度要比不銹鋼為基材的試樣高6 ,延伸率要高40 。
  3. Elastic - plastic analysis for soil around anchor jacked pile in this paper, the course of penetration is regarded as expansion of cylindrical cavity in infinite soil mass. combining with the knowledge of elastic mechanics and plastic mechanics, we can make analysis for soil around pile. finally, we can educe the cylindrical cavity pressure, radius of plastic zone, radical displacement in elastic zone, excess pore water pressure in soil around pile and spherical cavity pressure at the end of pile

    錨桿靜壓樁樁周土體的彈分析該部分是文章的主要工作所在,本文把壓樁過程樁周土體的本構關系看作是水平面的平面應變小孔擴張問題,利用小孔擴張原理,結合彈以及的知識,對壓樁後土體的狀作出分析,得出樁對土的擠擴作用力、樁周土體半徑、彈區的位移,壓樁完成瞬時樁周土體彈區和區的孔隙水壓力以及樁端球形孔擴張的擴張力。
  4. We possess a broad range of processing technologies both for producing general - purpose resin molds and also for two - color forming, super engineering plastic, thermosetting, screw products, etc. with regard to promising new products, we are currently developing a water - feeding device for flower pots and planters

    不僅有一般的樹脂模具,還有2色成形,強工料,熱硬化,螺絲等很多種加工技術。作為新開發產品的盆栽供水裝置也正在開發中。
  5. With the unique self - made cooling system, the ly12 is researched through the above method and the ultra - fine grain was obtained

    應用傳熱理論分析了採用該方法制備棒狀細晶材料的力條件和變形條件。
分享友人