超塑性的 的英文怎麼說
中文拼音 [chāosùxìngde]
超塑性的
英文
superplastic-
When the specimens are deformed in a long time at the optimal superplastic deformation condition, the microstructure is coarsened sharply. if the deformation time is shortened properly or the deformation temperature is decreased appropriately or strain rate is increased, homogeneous and fine equiaxed crystal microstructure can be obtained
在最佳超塑性條件下長時間變形時，合金顯微組織將發生明顯粗化，適當縮短變形時間、或適當降低超塑變形溫度及提高應變速率，可得到均勻細小的等軸組織。Isothermal superplastic solid - state welding of 4ocr and qcr0
5的恆溫超塑性固態焊接High - strain - rate superplasticity of metal matrix composites
金屬基復合材料的高速超塑性Progress in the study of superplasticity of silicon nitride ceramics
4陶瓷超塑性的研究進展High strain rate superplasticity of mmcs
復合材料的高應變速率超塑性High strain rate superplasticity in mb2 sic magnesium matrix composites
復合材料的高應變速率超塑性High strain rate superplasticity in sicp reinforced az31 magnesium matrix composite
金屬基復合材料的高應變速率超塑性Cavity behavior of sic mb2 magnesium matrix composites during high strain rate superplasticity deformation
2復合材料高應變速率超塑性變形的空洞行為Study on superplastic diffusion bonding of different steels
異種鋼材的超塑性擴散連接工藝研究Fatigue property and superplastic deformation of bulk amorphous alloys
塊體非晶態合金的疲勞性能與超塑性變形Microstructural evolution during superplastic deformation in large - grained single phase ni - 48al intermetallics
金屬間化合物超塑性變形過程中的組織演化Exploration enhancing strain stress of superplastic deformation using pendant hammer type tensile tester
採用吊垂式拉伸試驗機探討超塑性變形速度的提高方式The superplastic behavior of tc6 titanium on the condition of different temperature and different strain rate was explored
本文對不同初始應變速率和變形溫度條件下tc6鈦合金的超塑性變形行為進行了系統研究。The effects of temperature and strain rate were analyzed too. furthermore, the tensile fracture surface of tc6 titanium was analyzed by sem
分析了tc6鈦合金在變形過程中不同變形溫度、初始應變速率對流變應力的影響規律，並且對變形溫度、初始應變速率在tc6鈦合金超塑性變形中的顯著性進行了探討。This solution costs around us 15 excluding motor with cruise, brake, speed limit and driver control circuit monitoring. additional features include protection from in - reverse recharge and a mile - o - meter. shanghai acutec ltd, a distributor for nec, exhibited its 78k0s kx1 microcontroller - based electric bicycle technology that promises to solve difficult issues in brushless motor control by using nec s upd78f9222 as its main control unit
卜威超塑性成型法super plastic forming ，是利用特殊的調質方法，使用現有6061 - t6材質達到90 %高延伸率的狀態，來取代油注成型整個製程採用氣吹成型，壓力遠低於油注大約110 。The hsrs is very attractive for commercial application because it enables the material to be superplastic forged
材料的高應變速率超塑性能使材料可進行超塑性鍛造，使得該項技術具有誘人的工業應用前景。Abstract : in this paper, the substance and technological process of superplastic die forging are introduced, the present application situation and the die materials of superplastic die forging are enumerated, and the characteristics and advantages of superplastic die forging are elaborated
文摘:介紹了超塑性模鍛的實質及工藝過程；列舉了超塑性模鍛的應用現狀及模具材料；闡述了超塑性模鍛工藝的特點和優點。The experimental result of superplastic compression indicates that strain rate has intensive effect on flow stress of ti - 1023 alloy and the effect of temperature is related with strain rate
超塑性壓縮實驗結果表明，應變速率對ti - 1023合金流動應力具有強烈的影響，溫度對流動應力的影響程度與應變速率大小有關。In this paper, 130mm diameter hot - rolled bars ( 3 transus temperature is 798 c ) were used in experiments. the superplastic property of ti - 1023 alloy was studied systematically by the experiments of tensile and compression. the preparation method of fine - crystalline structure and the processing parameters of superplastic forging are optimized
本文以130mm熱軋棒材為原材料，通過超塑性拉伸和超塑性壓縮試驗，對ti - 1023合金的超塑性進行系統研究，研究坯料細晶組織制備方法，優化超塑成形工藝參數，為高筋薄腹板復雜形狀ti - 1023合金鍛件超塑性等溫模鍛工藝的制定提供試驗依據。Glossary of terms used in metallic superplastic materials
金屬超塑性材料的術語匯編分享友人