軸承徑向載荷 的英文怎麼說

中文拼音 [zhóuchéngjìngxiàngzǎihé]
軸承徑向載荷 英文
bearing radial load
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 承 : Ⅰ動詞1 （托著; 接著） bear; hold; carry 2 （承擔） undertake; contract （to do a job） 3 （客套話...
  • 徑 : Ⅰ名詞1 （狹窄的道路; 小路） footpath; path; track 2 （達到目的的方法） way; means 3 （直徑的簡稱...
  • 載 : 載Ⅰ名詞（年） year : 一年半載 six to twelve months; six months to a year; 三年五載 three to five ...
  • 荷 : 荷名詞（蓮） lotus
  • 軸承 : [機械工程] bearing; axle bearing; bearing of shafts; gudgeon block; mechanical bearing; pillow; s...
  • 載荷 : load; loading載荷變化 load fluctuation; variation in load; 載荷裝置 load device
  1. Angle contact ball bearing can be subject to both radial and axial load, it also can be subject to pure axial load, its axial load capacity is depend on the contact angle and increased accordingly. it can be used for high speed and high precision application dueto high limit speed and pre - adjustable rigidity

    角接觸球軸承可同時承受徑向載荷和軸向載荷，也可以承受純軸向載荷，其軸向載荷能力由接觸角決定，並隨接觸角增大而增大，且極限轉速較高，剛性大還可預調，適用於高速、高精度場合。
  2. Also the influences of the length, diameter, and the ratio of the stiffness of pipe to the stiffness of soil on the bearing mechanisms are discussed. based on these, some useful conclusions are reached

    然後從樁長、樁徑以及樁土剛度比等角度分析了其對單樁承載力、內外側摩阻力、樁端平面應力分佈、軸向荷載傳遞、樁身截面位移等的影響。
  3. Through teat of relative vibration, center - line and center orbit of the shaft during starting - up and carrying load process, the abrasion mechanism, radial disturbance, loading status, and self - centering capability etc. of the the failured bearing have been analysed, and measures for preventing damage of bearing shoes being put forward

    摘要通過對機組起動及帶負荷過程中軸的相對振動、軸中心線、軸心軌跡的測試，對失效軸承的磨損機理、徑向擾動、承載狀況和軸承自調心能力等進行分析，提出了預防軸瓦損傷的措施。
  4. In the test, static - dynamic method is used to measure the stiffness, the eight stiffness coefficients of the radial part and the two stiffness coefficients of the thrust part can be obtained though loading slowly to the testing bearing which is in a equilibrium position

    首先，對處于平衡位置的測試軸承分別沿水平方向、鉛垂方向及軸向緩慢施加載荷，根據靜動法原理求得各個轉速下測試軸承徑向部分內、外膜8個剛度系數以及推力部分內、外膜2個剛度系數。
  5. Author thinks that the direction of the maximum plastic distortion along a constant radius around the crack tip may be considered as the direction of shear - mode fracture ( named pmax - criterion ) and the load when located shear band prongs the ligament in the front of crack tip is regarded as the limited load of shear - mode fracture. ( 3 ) the fad ( fracture assessment diagram ) of titled crack is proposed based on achievements of mesomechanics about i - ii complex ductile fracture of metal, and the titled crack is classified two kinds : void - mode fracture is assessed by fracture assessment curve, and shear - mode fracture by limited load. ( 4 ) using a fe program based on plantle - ressue theory to calculate some mesomechanical parameters, a flange joint structure of a high pressure vessel ( design pressure 31. 4mpa and the thickness of the hemispherical head is half of that of shell. ) is analyzed to determine whether the structure under operation pressure is safe or not, forecast the mode of potential invalidation and argue for the rationality of design of the structure

    試件的整體斷裂為剪切型，但在試件芯部裂尖鈍化區中部出現了韌窩型啟裂並有一定的擴展，說明局部較高的應力三軸度也會使韌窩型機制得以發展，但是不改變試件整體的剪切型斷裂模式；對韌性斷裂的剪切模式的細觀機理做了一定的探討，並且提出了含裂紋構件剪切型斷裂的宏觀判據：認為裂紋前方的集中剪切帶中與裂紋尖端等半徑處最大有效塑性應變出現的方向可以作為裂紋剪切斷裂的方向（可簡稱為_ （ pmax ）準則） ，集中剪切滑移帶貫穿裂紋前方承載韌帶時的載荷可以作為極限載荷；本文運用金屬韌性斷裂細觀力學在一復合型韌性斷裂方面的研究成果，採用失效評定圖的形式，提出了傾斜裂紋的安全性評定方法的基本框架。
  6. Taper roller bearings are generally used to support combined load mainly consisting of radial load

    詳細信息:圓錐滾子軸承主要用以承受徑向載荷為主的徑向與軸向聯合載荷。
  7. With the different loading ratio of parallel to axis and normal to axis direction, damage defects will occur bulking problem. by varying the degree of material anisotropy relative to the loading axis such as poisson ' s ratio and shear modulus, crack growth bulking strain value parallel to or normal to the loading axis is different. the parameters controlling the growth or arrest of the delamination damage are identified as the geometry and the depth of defects and radius of cylindrical etc. at last, it was investigated that the delamination damage is often induced by the tip of matrix damage under higher stress

    研究結果表明:殼體筒段受軸向拉伸和內壓載荷作用時，軸向和環向載荷的比率不同，母層和子層可能發生拉伸屈曲，也可能發生收縮屈曲，或者同時發生拉伸和壓縮屈曲;母層與子層各向異性存在差異，即泊松比與剪切模量不匹配時，將使子層板的邊界上承受壓縮和剪切作用，當分層達到臨界狀態則發生屈曲，當母層與子層的各向異性差異越大，則發生分層屈曲的可能性越大;分層損傷的屈曲應變值與子層自身的彈性模量、分層子層的形狀、厚度以及圓柱半徑等因素有關。
  8. Compares with the same centripetal ball bearing, has the big radial direction load bearing capacity, mainly is suitable for the cold hot - rolling mill, working roll support rolls and so on cogging mill

    與相同的向心球軸承相比，有較大的徑向負荷承載能力，主要適用於冷熱軋機，開坯機等工作輥支承輥。
  9. Plain bearing block housings are made up of cap, base, aluminum bronze bushing and installing bolts, which mainly bear radial load

    滑動軸承座由上蓋、底座、剖分軸瓦（鋁青銅） ，安裝螺栓組成，主要承受徑向載荷。
  10. The thesis bases on reynolds - equation and researches the working state under the static and dynamic loading situation of the object. under the static loading situation, the steady - state center position of journal is an important parameter, it is discussed, especially under three - lobe bearing, the calculating progress of it has a detailed description, and the progress is practiced by the means of computer programmer

    徑向滑動軸承是其中的重要一類，本論文以徑向滑動軸承為研究對象，以雷諾方程的建立及求解過程為理論基礎，對滑動軸承的處于動態及靜態載荷下的工況情況進行了理論分析。
  11. Four row circular cone roller bearings its performance and double row circular cone roller bearings basic same, but may withstand the bigger radial direction load and the two axle to the load

    四列圓錐滾子軸承其性能與雙列圓錐滾子軸承基本相同，但可承受更大的徑向載荷和雙軸向載荷。
  12. Compares with the single row circular cone roller bearings, has may withstand the big radial direction load primarily radial direction load, mainly uses in withstanding the radial direction load primarily diameter, the axial union load function

    與單列圓錐滾子軸承相比，具有可承受較大徑向載荷為主的徑向負荷，主要用於承受徑向負荷為主的徑、軸向聯合負荷作用。
  13. These bearings are featured by the extremely big axial load carrying capacity and mean while they can also carry cetrain radial load

    軸向載荷能力非常大，在承受軸向載荷的同時還可以徹骨你受干徑向載荷。
  14. Xr series rigid tooth flank helical gear units have the feature of high versatility, good combination and heavy loading capability, along with other merits such as easying to attain various transmission ratio, high efficiency, low vibration and high permissible axis radial load

    Xr系列斜輪硬面減速機是通用性強組合性好承載能力高的一種減速機，它不僅很方便地獲得各種不同的傳動比，而且效率高振動小允許有高的軸伸徑向載荷。
  15. When radial load is applied, the active bearing can surpress the displacement of the shaft, thus obtaining an infinite stiffness

    當有徑向載荷作用時，自主式軸承能抑制軸頸位移並因此使軸承獲得無窮剛度。
分享友人
分享到 Line

分享到臉書