軸承油泵 的英文怎麼說
中文拼音 [zhóuchéngyóubèng]
軸承油泵
英文
bearing oil pump- 軸 : 軸Ⅰ名詞1. (圓柱形的零件) axle; shaft 2. (對稱部分的直線) axis 3. (圓柱形的纏繞器物) roller; spool Ⅱ量詞(用於纏在軸上的線以及裝裱帶軸子的字畫)
- 承 : Ⅰ動詞1 (托著; 接著) bear; hold; carry 2 (承擔) undertake; contract (to do a job) 3 (客套話...
- 油 : Ⅰ名詞1 (脂肪; 油脂) oil; fat; grease 2 (姓氏) a surname Ⅱ動詞1 (用桐油、油漆等塗抹) apply t...
- 泵 : 名詞(吸入和排出流體的機械) pump
- 軸承 : [機械工程] bearing; axle bearing; bearing of shafts; gudgeon block; mechanical bearing; pillow; s...
-
High alloy carburizing steel and 20crmnti structure steel etc. they also can be used for oil - quenching, gas - quenching and annealing of tool and mould steel, all kinds of steels used in precision bearing, parts of oil - pump, nozzle and precision machine
等結構鋼的滲碳及滲碳后的淬火,工模具鋼精密軸承油泵油嘴機械件精密機器零件等各種鋼的氣淬退火等。Lqry series hot oil pump is supported by the ball bearings at the both ends, front end lubricated by lubricating oil, while back end lubricated by grease, with an oil conduit in the middle used to observe the conditions of sealing and recovery of heat conduction oil
Lqry系列熱油泵的支撐採用了雙端球軸承支撐的結構形式,前端採用潤滑油潤滑,後端採用潤滑脂潤滑,中間有一導油管,用以隨時觀察密封情況和回收導熱油。The reason for oil leak lies in the sealing problem of bearing box ends of centrifugal pump
離心泵軸頭甩油實質是離心泵軸承箱兩端密封問題。Through the statistic analysis on the change of the melt gear pump working condition pre - and post - pet plant capacity increasing and concatenate direct spinning process, the reasons for the unsteady running were studied, the modification measures such as lubricating the oil groove with sliding bearing, mechanical sealing of the gear pump, decreasing the gear pump outlet pressure, changing the automatic speed increasing to hand speed increasing were put forward
摘要通過對聚酯裝置增容和後接直紡長絲前後熔體齒輪泵工況變化的統計分析,研究其運行不穩定的原因,提出改造措施,包括滑動軸承潤滑油槽,齒輪泵的機械密封,降低齒輪泵出口壓力,改自動提速為手動提速等等。The mainly works had been done as follows : 1. in order to keep commonality, the modules who have similar thermodynamic process had been classed. such as evaporating module ( including furnace, drum, system of boiler recycled water ), single - phase heat exchange module ( including superheater, reheater, ecomomizer ), lubricating oil system module ( can be used for any lubricating oil system of rotation mechanical impedance ), pump and fan module, ect
本文所作的主要工作如下: 1 、為保證模塊的通用性,對鍋爐有相似熱力環節的模塊進行分類,建立模塊庫,便於模塊調用,如蒸發區模塊(包括爐膛、汽包和爐水循環系統) ,單相換熱模塊(包括過熱器,再熱器,省煤器等) ,潤滑油系統模塊(可用於各種轉機軸承潤滑油的動態特性的計算) ,泵與風機的動態計算模塊等。For pump shafts, the results reveal that the stress in the spline is higher than the other parts of the shaft, and the highest stress is at bottom and terminal of the spline. in fact, the broken of shafts is at the same position ; it demonstrates that the calculation is right
實踐證明,軸斷部位基本集中在潛油泵軸花鍵的根部,說明計算結果和實際是吻合的;對于潛油電機軸,應力集中點主要處在軸承鍵與環槽的交界處和花鍵的根部。Bearing oil pump
軸承潤滑油泵A complete range of steering parts such as knuckles, steering cylinders and repair kits, bushings and bearings, bell cranks, tie - rods, hand wheels, horn kits, power steering motors and pumps, king pin kits and other steering system parts
我們擁有完整的轉向系統配件,例如轉向節、轉向油缸及修理包、襯套及軸承、轉向拉桿、手輪、喇叭及修理包、動力轉向馬達及油泵、中心銷及該系統的其它配件。Taking the hydrostatic equilibrium of axial force of pump dm360 as the example, this paper elaborates design calculation and dynamic - static characteristic analysis of hydrostatic bearing with twisting plate throttle, derives design parameters and formulas of bearing structure, discusses effects of various main factors ( oil viscosity, compressibility, distortion coefficient of twisting plate, pressure of oil source, and bearing clearance ) on dynamic characteristic, and obtains some conclusions about the application of hydrostatic bearing in engineering practice
本文以dm360型泵軸向力的液體靜壓支承平衡為例,對扭板節流靜壓支承的設計計算和動靜態特性分析進行了較為詳盡的闡述,推導出支承結構的設計參數和公式,討論了各種主要因素(油液的粘度、油液的可壓縮性、扭板變形系數、供油壓力、支承間隙)對支承動態特性的影響,給出了一些結論。8. taking precise plungers of oil pump mouth and bearings produced in a large scale as the objects, practical application and verification of above theoretically research results were made
以大批量生產的油泵油咀柱塞精密偶件和軸承件為對象,對上述理論研究結果進行了實際應用與驗證。分享友人