金屬包層板 的英文怎麼說
中文拼音 [jīnzhǔbāocéngbǎn]
金屬包層板
英文
metal clad board- 金 : Ⅰ名詞1 (金屬) metals 2 (錢) money 3 (古時金屬制的打擊樂器) ancient metal percussion instrum...
- 屬 : 屬名詞1 (類別) category 2 [生物學] (生物分類系統上所用的等級之一) genus 3 (家屬; 親屬) fami...
- 層 : i 量詞1 (用於重疊、積累的東西 如樓層、階層、地層) storey; tier; stratum 2 (用於可以分項分步的...
- 板 : Ⅰ名詞1 (片狀硬物體) board; plank; plate 2 (專指店鋪的門板) shutter 3 [音樂] (打拍子的樂器) ...
- 金屬 : metal
-
In this paper, a high performance sma system applied to steel bridge deck is put forth in allusion to the pavement project of the wuhan junshan yangtze river highway bridge. it comprises steel slab, zn coating layer, closing layer, adhesive, pre - mixed asphalt stone and dual layer sma from bottom to top. it is based on the fea results of the forces and deformation of the pavement layer by means of the algor feas, according to this bridge ' s traffic and the ambient temperature varying range of the pavement layer
本文針對武漢軍山長江公路大橋鋼箱梁橋面鋪裝工程,從鋪裝層環境溫度變化范圍、交通量等使用條件出發,在用algorfeas有限元分析軟體分析鋪裝層受力變形基礎上,提出了(即鋼板+金屬鋅塗層+封閉層+粘接劑+預拌瀝青碎石+雙層sma )的高性能鋼橋面sma鋪裝體系,並對這種sma的組成材料,包括改性瀝青、集料、礦粉、纖維進行了比較研究,設計了這種sma的配合比,對sma混合料的性能進行了對比試驗,對這種sma方案進行了疲勞性能研究,驗證了所選擇sma方案的可行性。Analysis of metal - clad graded index planar optical waveguides with edge element method
金屬包層漸變平板光波導的邊緣元分析However, the die attach layer delaminated after 500 cycles and pcb cracked in the underfilled samples after long time cycling. c - sam is employed to investigate the delamination in the underfilled samples. highly concentrated stress - strain induced by the cte mismatch between the bga component and the pcb board, coarsened grain and two kinds of intermetallic compounds ( nisn / nisns ) which formed during reflow and thermal cycle and their impact on the reliability of solder joints are discussed in this paper
充膠樣品粗化尤為嚴重; ? ni - sn金屬間化合物包括兩層:其中,靠近ni焊盤的那層比較平整,同時, eds結果分析表明其化學式近似為nisn ,而靠近焊料的那層呈板條狀,化學式近似為nisn _ 3 ,文獻表明其為亞穩相; ?充膠使得樣品最大應力范圍降了接近一個數量級並降低了dnp的作用,同時,器件失效模式變為晶元粘接層分層; ? c - sam結果表明本論文採用的充膠樣品,晶元粘接層分層起始於500周左右,而經過2700周循環的樣品,分層幾乎擴展到整個界面。Packaging code - regenerated cellulose film, films made of plastics, aluminium foil, flexible multilayer structures and metallized materials
包裝規程.第21節:再生纖維素薄膜,塑料薄膜,鋁箔,撓性多層板和金屬化材料The book also considers forming technologies for various composite material forms including thermoset and thermoplastic prepreg, molding compounds, and composite / metal laminates
該書還認為成形技術,為各種復合材料的形式,包括熱固性和熱塑性預浸料,成型化合物,並復合/金屬層板。Testing of clad steels ; determination of shear strength between cladding metal and parent metal in shear test
包層鋼板的檢驗.剪切試驗中包層金屬與母體材料之間的The coating is applied on the surface of the rolled, pressed aluminium plates
這一塗層是應用於包金箔的、壓制的鋁制金屬板上的。分享友人