鑄造性能 的英文怎麼說

中文拼音 [zhùzàoxìngnéng]
鑄造性能 英文
castability
  • 鑄 : Ⅰ動詞（鑄造） cast; coin; make Ⅱ名詞1. （古國名） zhu, a state in the zhou dynasty2. （姓氏） a surname
  • 造 : Ⅰ動詞1 （做; 製作） make; build; create; produce 2 （假編） cook up; fabricate; concoct 3 [書面語...
  • 性 : Ⅰ名詞1 （性格） nature; character; disposition 2 （性能; 性質） property; quality 3 （性別） sex ...
  • 能 : 能名詞（姓氏） a surname
  • 鑄造 : [冶金學] cast-on outwell; foundry; cast; casting; found; founding
  1. A detailed introduction was made to the properties of the wet coated sand suitable for multi - station shell mould shooting machine ; the development of a sort of high strength coated sand with low resin content : the shaping index and wetness adjusting process : analysis and prevention of peel back defect of shells made with overturning hopper process ; test method of peel back resistance of coated sand : pinhole defect analysis of high ni ductile iron shell mould castings and application of anti - pinhole coated sand

    詳細介紹適用於吹砂式多工位殼型機的濕態覆膜砂性能；高強度低樹脂量覆膜砂的研製；濕態殼型覆膜砂的成形性指數與調濕工藝；翻鬥法制殼時的脫殼問題分析和解決辦法；覆膜砂脫殼性檢測方法；高鎳球鐵件殼型鑄造表面針孔原因分析與抗針孔覆膜砂的應用。
  2. Test method for properties of investment casting ceramic core - part 6 : determination of dissolubility

    熔模鑄造陶瓷型芯性能試驗方法第6部分:溶失性的測定
  3. The result of those studies as follow : ( 1 ) an composite layer of definite thickness on the casting was gained by cast - sintering technique, and it has well wear - resistance. ( 2 ) the reinforcement of the composite layer is tic or vc, which was exiguous and is well distributed

    同時利用干滑動摩擦磨損實驗，對表面復合層的耐干滑動摩擦磨損的性能進行了研究。研究表明： （ 1 ）利用鑄造燒結技術可以在鑄件表面獲得一定厚度耐磨性能良好的表面復合層。
  4. It improves fluidity and other casting properties.

    它可提高流度和其他鑄造性能。
  5. Russia kv - 1 1942 heavy cast turret tank because warlike vehemence, the kriov factory gave birth to casts the kv - 1 of the quick - fried tower, nameding after the kv - 1 model 1942 heavy cast turret, turret in this kind of foundry contain better bullet - proof features, the armor thickness also comes to 95 mm of, the main firecrackers also changed to pack better types zis - 5s in function 76. 2 mm artillery

    因為戰爭的激烈，基洛夫工廠kroiv生產了鑄造炮塔的kv - 1 ，命名為kv - 1 1942年型重型鑄造炮塔，這種鑄造炮塔有更好的防彈外型，裝甲厚度也達到了95毫米，主炮也換裝了性能更好的zis - 5型76 . 2毫米炮。
  6. Test method for castability of alloys. determination of hot tearing tendentiousness

    合金鑄造性能測定方法.熱裂傾向的測定
  7. In stead of submission, women can choose to challenge and topple over the superiority of men in the patriarchy society

    摘要由男性鑄造的傳統社會將女性視為低下的：她只能通過挑戰和改變男性高等地位的途徑來改變自己低下的地位，贏得真正的女性身份。
  8. C. application : it is used in making glassware - plate glass, wired glass, figured glass, hollow glass, foam glass and glass block as beer bottle, cups, vacuum flask, optical glass, fiberglass and so forth. its application is common in founding, smelting, fireproof material, cement and chemical industry

    用途：製造玻璃，耐火材料，冶煉矽鐵，冶金熔劑，陶瓷，研磨材料，鑄造，石英在建築中利用其有很強的抗酸性介質浸蝕能力，用來制取耐酸混凝土及耐酸砂漿。
  9. The age hardening characteristic of as - cast cu20ni20mn and cu20ni35mn alloys and the interface characteristic between the alloy and cast tungsten carbide were studied, and on the basis of this study, composites of cu - ni - mn alloy reinforced with different volume fraction ( 0 - 45vol. % ) and different size ( 42 - 362 m ) of cast tungsten carbide particles were made by vacuum hot - pressing liquid sintering technology. pin on disk two body abrasion tests have been performed with different size of sic abrasive under different loads

    本文研究了鑄態cu20ni20mn和cu20ni35mn合金的時效硬化特性及其與鑄造碳化鎢的界面特性，並在此基礎上以不同尺寸（ 42 362 m ）的鑄造碳化鎢顆粒為增強體，採用真空熱壓液相燒結技術制備了不同顆粒含量（ 0 45vol . ）的鑄造碳化鎢顆粒增強cu - ni - mn合金基復合材料；以不同粒度的sic為磨料，在不同載荷條件下利用銷?盤磨損試驗機測試了復合材料的二體磨料磨損性能。
  10. When the atomic ratio of nb is one, the structure is homogeneous and almost composed of the single sm2fe17 phase. it ' s nearly the same structure as that after annealing. so it can reduce the production cost and increase the stability of magnetic properties

    當nb的原子比為1時的鑄態組織基本為均勻的接近單相的sm _ 2fe _ （ 17 ）組織，已接近於退火后的組織，從而可以避免冗長的均勻化退火化過程而直接用於製造永磁體，極大的降低了生產成本，並能有效的提高磁性能的穩定性。
  11. 4. fine - blanking technology can obtain material deformation, deburring without secondary machining. 5. such as carbon steels, alloyed steels, stainless steels, aluminium alloy, yellow bronze, red bronze and bronze alloy material, compared with power refining or forging technology, fine - blanking products can obtain more strengthened constitution and against polishing when surface polishing

    諸如碳鋼合金鋼不銹鋼鋁合金黃銅紅銅與銅合金等材質，利用精沖技術所產生的產品，與粉沫冶金或鑄造技術所產生的產品比較在表面拋光時能保證材料主體之較優結構強度與抗磨性。
  12. The failure of manufacturing cu alloy valve body by die castin g and hot extrusi on casting were point out. characteristics of squeeze casting technology were exp ounded. application of squeeze casting to cu alloy valve body in gas fired applia nce and influence of specific pressure on properties of product were analyzed

    指出了壓力鑄造及熱擠壓工藝生產銅合金閥體的缺點，闡述了擠壓鑄造工藝的特徵，介紹了擠壓鑄造在燃氣器具銅合金閥體上的應用，分析了比壓對產品性能的影響。
  13. Examination of the density, strength, hardness and microstructure showed that the mechanical properties and structure of the part made by direct metal forming process are better than that obtained from selective laser sintering process, as good as or even better than castings

    對成形件進行的密度、強度和硬度指標測試和金相組織觀察表明：基於弧焊的直接金屬成形件的組織結構和力學性能指標明顯優于選擇性激光燒結工藝成形件，達到或高於鑄造零件。
  14. The results show that the composites were more wear resistant than the matrix, contributing to the " volume effect " and " size effect ", the wear resistance increases with the particle content and size. the composite shows better wear resistance than high chromium cast iron material especially in low load and fine abrasive test condition. the results also indicate that the composite strengthened by ageing treatment was more wear resistant than as - cast composite

    磨損試驗結果表明，鑄造碳化鎢顆粒增強cu - ni - mn合金基復合材料具有比較高的抗磨料磨損能力，而且其耐磨性隨著鑄造碳化鎢顆粒體積分數及尺寸的增大而提高，表現出了強烈的「體積效應」及「尺寸效應」 ，尤其是在低載荷、細磨料磨損條件下，復合材料表現出更好的而寸磨性，即使與高鉻鑄鐵（ cr28 ）相比也有很大程度的提高。
  15. Rapid prototyping technology changed the traditional pattern of product design, which could offer product sample for the designer, reduced design cycle and quicken the schedule of new product design, and it gave the decision - makers visual feeling. ; rp technology provided kinds of molds including resin - boncled mold laminate mold, investment mold and lost foam casting mold and so on for sand casting investment casting and cavityless casting, it could also use direct shell production casting to make pattern dies metal dies die - casting dies injection dies directly, and it could even produce casting products in small scales. the applications of fdm technology in plaster precision casting and the rapid casting technology based on sls technology were introduced, the organic combination between rapid prototyping tecnnology and foundry process, which initiated a new period of rapid manufacturing metal parts, by using advanced new technology alternated traditional foundry industry to make it looked brand - new, thus, the competition of foundry industry would be improved ; rapid prototyping technology offered a rapid economical feasible technical method, common processes of using rapid prototyping technology to produce dies were discussed, in the paper it explored that. the problem of combining rapid prototyping technology with electric arc metal - spraying technology to make metal dies and technics in dies manufacturing of combining rapid prototyping technology with precision casting, rapid tooling based on rapid prototyping, integrated advanced new technology and tradition technology of rapid prototyping manufacture, each superiority were exerted, rapid prototyping technology had been an efficiency measure to rapid update products and develop new product, and to middle -

    快速成型技術改變了傳統的產品開發模式，可以為設計者提供產品樣件，縮短設計周期，加快新產品的開發進度，為決策者提供直觀性；快速成型技術迅速提供砂型鑄造、熔模鑄造、實型鑄造用的各種模樣，包括樹脂模、層壓模、熔模和消失模等，還可採用直接制殼鑄造法直接製造熔模鑄造用的壓型、金屬型、壓鑄型、注塑模，甚至直接製造小批量鑄件，介紹了熔積成型技術在石膏型精密鑄造上的應用和基於選擇性激光燒結技術的快速鑄造技術，快速成型技術與鑄造工藝的有機結合，開創了快速製造金屬零件的新階段，對用高新技術改造傳統的鑄造工業，使其面貌煥然一新，增強鑄造行業的競爭能力；快速成型技術為母模的製造提供了一條快速、經濟、可行的技術途徑，討論了利用快速成型技術製造模具的一般工藝方法，探討了將快速成型技術與金屬電弧噴鍍技術結合起來快速製造金屬模具問題，以及快速成型技術與精密鑄造技術相結合的模具製造工藝，基於快速成型製造的快速模具技術，集成了快速成型製造高新技術和傳統技術，發揮各自優勢，已成為產品快速更新換代和新產品開發及中、小批量生產的有效手段之一。
  16. Some constructive suggestions were proposed on the energy saving technique development of china foundry industry

    並對發展我國鑄造節能技術提出了幾點建設性意見。
  17. The effect of compound casting technology and compound modification on the properties of high speed steel roll collar was studied. the results showed that compound high speed steel roll collar with high and even hardness and good bond between outer and inner layers could be gained when the modified colbalt free high speed steel in outer layer and nodular iron inner layer in connection with appropriate rotational speed of centrifugal machine, pertinent pouring interval between two kinds of the melt and moderate pouring temperature as well as surface induction heat treatment were chosen. it is indicated in industrial use that the service life of compound roll collar is higher by 5 times than that of high chromium cast iron collar

    研究了離心復合鑄造工藝和復合變質處理對高速鋼輥環性能的影響，結果表明，選用變質高碳無鈷高速鋼作外層，用球鐵作內層，選擇合適的離心機轉速、兩種金屬熔液澆注間隔時間和澆注溫度，結合採用表面感應熱處理工藝，可獲得硬度高、均勻性好、內外層結合良好的高速鋼復合輥環，用於工業生產其使用壽命比高鉻鑄鐵輥環提高5倍以上。
  18. By means of mechanical properties determination, optic and electronic microscope examination and practical application it is verified that the usage of cap type filter could improve steel casting properties and effectively reduce inclusive cast defects in investment casting

    通過測定鑄鋼試樣的力學性能、進行金相分析、電子顯微分析和生產應用，驗證了採用熔模鑄造帽式過濾器能改善鑄鋼性能、有效減少精鑄件由於夾雜所造成的廢品。
  19. Forgemaster effects should show up correctly on non - magical items

    鑄造只能給白色的物品加屬性了。
  20. Test for castability

    鑄造性能試驗
分享友人
分享到 Line

分享到臉書