限制前饋 的英文怎麼說

中文拼音 [xiànzhìqiánkuì]
限制前饋 英文
limiting feedforward
  • 限 : Ⅰ名詞（指定的范圍; 限度） limit; bounds Ⅱ動詞（指定范圍, 不許超過） set a limit; limit; restrict
  • 制 : Ⅰ動詞1 （製造） make; manufacture 2 （擬訂; 規定） draw up; establish 3 （用強力約束; 限定; 管束...
  • 前 : Ⅰ名詞1 （在正面的） front 2 （次序在先的） first; top 3 （過去的; 較早的） ago; before; preceding...
  • 饋 : 動詞（饋贈） make a present of
  • 限制 : place [impose] restrictions on [to]; astrict; restrict; limit; confine; shut down on [upon]: 限制...
  1. Output can be obtain, next we use our designed the wavelet soft threshold to select result of the wavelet transform, finally, we give the selected result reversal wavelet transform. it is obvious : the wavelet soft threshold is important to improve the quality of the gray image processing. i give the donoho wavelet soft threshold a modified value method, which has a relation with ratio of signal - noise. i made full use of discrete hop field single feedback neural network, and nonlinear steady of automatic system at last, i obtained a steady limited ring, give the energy function an order differential a optimal

    我的思路是：改造現有圖形結構，先建立能反映信噪比大小且含待定參數k的表達式，然後通過離散型h0pfi舊單層反饋神經網路，再結合前邊的混合濾波器構成一個非線性控制系統，寫出對應的網路函數，利用相平面法和李雅普諾大穩定性的判據，得到一個穩定的極限環，從而確定出參數卜的范圍，進而再對原來的小波軟閾值進行修正，用修正後的值作為小波閾值。
  2. Therefore, the main subject of this research is to discuss the application of all - around cost management through the full process control, which consists of three parts : feed - forward control, which seeks to anticipate the cost movement ; process control which sets down cost standards and cost planning in order to limit the cost payout

    因此本文主要是通過成本的全過程式控制制來論述全面成本管理的實際應用，其主要內容包括三個部分：前饋控制旨在預測成本變動的方向；過程式控制制通過制定成本標準和成本計劃，限定成本的支出；反饋控制通過分析實際成本與成本計劃的差異，分析和調查原因，以找到降低成本的方法。
  3. Based on x - filtered lms algorithm and - filtered lms algorithm adaptive inverse control, we use a new variable step size lms algorithm. adding little computation, variable step size lms algorithm can result in fast convergence speed and low residual error simultaneously. the adaptive feedback control can counteract the beginning error of the system

    在原來的x -濾波lms演算法自適應逆控制和-濾波lms演算法自適應逆控制方法的基礎上，引入了新的變步長lms演算法，在計算量增加不多的前提下，能同時獲得較快的收斂速度和較小的穩態誤差；引入自適應的反饋補償控制克服了被控系統的直流零頻漂移，使控制系統在初開始工作階段快速收斂；還引入自適應擾動消除器，它能最大限度的消除擾動。
  4. The aimd has got a widely apply for its briefness and ease. at the other hand, it contain limited information because it has only two status : overload or under load. it cannot represent the true demand of the receiver and at the same time the policies of window adjust destroy the demand of smoothness of load, so it cannot afford the request of real - time streaming media

    Aimd從演算法的簡單性和實際網路容易實現的角度考慮，反饋給發送方的信息有限，只有過載或欠載兩種二進制狀態； aimd演算法根據瓶頸資源的擁塞狀態向所有用戶發送相同的反饋信號，並不能真實反映接收節點對發送方負載量的要求;同時， aimd的窗口調整策略破壞了負載平滑性的要求，不能滿足當前實時流媒體應用， aimd的這些不足，體現了一種性能和系統復雜度之間的折衷。
  5. At the same time, this paper summarized the experience on solving the problem of amplitude limitation of the controller output and proposed a method to predict system output by use of the model prediction with feedback correction. the on - line intelligence switch of controller output between the limited amplitude and imc controller output is determined according to the state whether the system output and the predictive output are within the given error range

    同時，本文在總結前人對輸入受限問題的處理經驗的前提下，提出用帶反饋校正的模型預測作系統輸出預測，根據系統響應和系統預測值是否在給定誤差范圍內來共同決定控制量在限幅值與內模控制器輸出值之間進行在線智能切換。
  6. By solving iterative the sequences, the optimal control law is obtained which consists of analytical linear feed - forward - feedback terms and a nonlinear compensation term, which is the limit of the adjoint vector sequence

    通過迭代序列得到的最優撫動抑制控制律由解析的線性前饋反饋項和序列極限形式的非線性補償項組成。
  7. Most of active headsets, which use fixed analog feedback controllers, are not able to maximize the noise reduction

    摘要目前有源耳罩大都採用固定的模擬反饋控制器，不能夠最大限度地消除低頻噪聲。
  8. Feedforward - feedback control method is presented to suppress the vibration of platforms. and the controller is designed accounting for noise ( model and measurement ), the limits of amd stroke and control input force

    提出了適用於海洋平臺的前饋-反饋振動控制方法，在控制器的設計中，考慮了噪聲（動態噪聲和測量噪聲）的影響，及amd沖程、控制力大小受到限制等實際情況。
分享友人
分享到 Line

分享到臉書