隙距比 的英文怎麼說
中文拼音 [xìjùbǐ]
隙距比
英文
clearance ratio-
The basic concept of siw is that it use the top and bottom layers of metal together with two row of vias is very small compared with wavelength, the dissipation loss of radiation is very small. it acts like a rectangular waveguide filled with some dielectrics, so components which can be composed by rectangular waveguide can also composed by siw such as antenna, filter, power divider, coupler, resonator
基片集成波導的基本概念是利用基片的上下金屬板和兩排間隔一定距離的金屬孔構成波導的金屬壁，由於每排金屬孔孔間距遠小於波長，因此由縫隙泄漏的能量很小，這相當于內部填充了介質的矩形波導，所以能夠用矩形普通波導實現的結構也都可以用基片集成波導來實現，比如功分器、濾波器、天線、耦合器、振蕩器等。Linear induction motor is an important kind of machines which have some merits such as simple structure, low cost, durability, convenience for maintenance etc. the subject of this thesis is to study a big circular ring linear induction motor, and the major works in this thesis are summarized as follows : ( 1 ) considering the effects of the finite length of primary core, one - dimension analytical solution for the air gap field is cited in this paper. based on it, the single layer winding magnetic field is studied. considering whole - pitched and short - pitched winding configuration with odd poles and half - fulled slots in both ends, the double - layer winding magnetic field is analyzed, respectively
本文對大圓環直線感應電機進行了深入細致研究，內容包括： （ 1 ）本文採用有限長行波面電流作用於有限長鐵芯上的模型，引用了氣隙磁場一維解，研究了單層繞組磁場，奇數極半填槽雙層繞組在採用整距和短距時磁場的分析、比較，簡單介紹了二維解； （ 2 ）用有限元軟體ansoft對大圓環直線感應電機空載氣隙磁場進行了靜態分析，並分析了結果； （ 3 ）用軟體進行了額定電壓下的瞬態分析，得到了轉矩，位移，轉速隨時間變化曲線圖，利用單極性霍爾元件測定轉速並與軟體計算結果進行了比較，採用等效電路法計算了堵轉時的最大電磁力並做實驗進行了驗證，由實驗測得了三相電流波形，並與計算結果進行了比較，對其不對稱性進行了定性分析。It was found that the ultra - fine powder can flow smoothly in a spouted bed with a draft tube under some sorts of design parameter and operating condition, thus a new effective method to improve fluidization quality of the ultra - fine powders is obtained ; at higher supplied gas velocity, an increase in the solid circulation rate is observed ; the extent of the distance between the nozzle and the draft tube inlet result in the promotion of the solid circulation rate ; the solid circulation rate increase with increasing the draft tube diameter or the bed mass ; the gas bypassing is nearly zero in the present work ; and the solid flow in the annulus is observed as a moving bed
結果表明：在一定的床層結構和操作條件下，超細粉可以在導向管噴動床中實現平穩流化，從而為改善超細粉的流化質量提供了一種有效的新方法；固體循環速率與噴動氣流量、導向管直徑、導向管底部與噴嘴出口間距以及床層裝填量成正比；氣體則基本上不存在「旁路」現象；環隙區中的顆粒流動表現為一移動床特徵。( 4 ) according to the 2 - d advective - dispersive equation of pore medium and combining the result of experiment, the difference between experiment and calculation was located by macroscopical analysis. a new mathematical model suiting to fractured medium was deduced from revised pore medium model. the correction and practicability were verified by the result of experiment
（ 4 ）依照孔隙介質二維溶質對流彌散方程，結合實驗所取得的成果，進行宏觀比較分析，找出實驗與計算的差距，然後對孔隙介質模型作進一步的修正，推導出了適合單裂隙巖體二維溶質運移的數學方程，並通過具體的實驗結果驗證了模型的正確性和實用性。The threshold speed and the typical characteristics of the oil whip of the system are simulated under the nonlinear model of oil film force, and the state of motion and type of the bifurcation are analyzed by floquet multiplicators which is computed by the shooting method. secondly, the the nonlinear dynamical model of the low - pressure rotor - bearing system by column bearing with reduced dimensions is presented. the numerical results show the rule of the amplitude with the eccentricity of rotor, the length - to - diameter ratio, oil viscosity and the clearance - to - radius ratio of the bearing under the definite speed
其次，對降維后的低壓轉子?軸承系統的非線性動力學方程，計算了圓柱瓦軸承支撐的轉子系統的振動穩定性在固定轉速下隨偏心距、軸承長徑比、潤滑油動力粘度和軸承間隙比的變化規律，並分析了轉子前軸承軸頸的失穩轉速與轉子偏心距、軸承長徑比、潤滑油動力粘度和軸承間隙比之間的關系，同時利用floquet理論分析其運動狀態和分岔類型。Abstract : the paper suggests two methods for adjusting the mesh clearance in cylindrical worm drive : one is to adjust the meshing center distance of worm gears, the other is to use dual lead cylindrical worm, introducing briefly the principle of adjustment and making a comparison between the characteristics of the two methods
文摘:提出了兩種調整圓柱蝸桿傳動嚙合側隙的方法:通過改變蝸輪蝸桿的嚙合中心距來改變其嚙合側隙;採用雙導程蝸桿傳動以調整蝸輪蝸桿的嚙合側隙，簡述了調整原理，並比較了兩種調整方法各自的特點。分享友人