電解液液面 的英文怎麼說

中文拼音 [diànjiěyèyèmiàn]
電解液液面 英文
electrolyte level
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 解 : 解動詞（解送） send under guard
  • 液 : 名詞（液體） liquid; fluid; juice
  • 面 : Ⅰ名詞1 （頭的前部; 臉） face 2 （物體的表面） surface; top 3 （外露的一層或正面） outside; the ri...
  • 電解 : electrolyze; electrolysis; electrolyzation; galvanolysis 電解銅 [冶金學] electrolytic [cathode] c...
  1. For electrodeposition by dc methods, the metals deposite uninterrupted and the particles were also embeded uninterrupted into the coatings ; for electrodeposition by pc method, the particles with biggish volume were desorbed from the coatings and returned to the electrolyte again owing to the presence of pulse interval ; for electrodeposition by prc method, the particles carried positive charges are much more easy to desorb from the coatings owing to the effecf of reverse pulse current combined with pulse interval, in addition, the reverse pulse current also could dissovle the metals, further accelerates the desorption of particles, thus the particles size embeded in the coatings by prc method is the least

    直流電沉積時，基質金屬的沉積連續進行，粒子在電極表面不間斷嵌入鍍層;單脈沖電沉積由於脈沖間歇的存在使得具有較大體積的粒子會脫附，重新回到溶液中;採用周期換向脈沖時，反向脈沖電流使表面荷正電的較大的粒子更易從電極表面脫附，同時，反向脈沖電流對基質金屬的溶解作用，也會促進粒子的脫附，因此鍍層中復合粒子尺寸最小。隨著鍍層中粒子復合量的增加，三種鍍層的晶粒都明顯細化，說明al _ 2o _ 3的存在阻止了晶粒的長大，提高了電沉積過程中晶核的形成速率。
  2. A liquid junction is the interface between two miscible electrolyte solutions.

    液體接界是兩個可混溶液的電解質溶液之間的界面。
  3. With the other hand, squeeze the bulb which forms pressure in the cell and forces air and (or) electrolyte through any leaks that may be present in the sealing compound.

    另一方面，壓擠橡膠球，使單格電池內部產生壓力，迫使空氣和（或）電解液穿過封口劑上任何可能存在的縫隙。
  4. Most author agree that they include interactions at the contact of solid particles and electrolytic solution which exist in the ground.

    大多數作者認為，它們包括了地層中固體顆粒與電解質溶液接觸面上所發生的相互作用。
  5. The method of obtaining high concentration of na2feo4 solution by quick electrolysis mainly contains four aspects : adoption of either a diaphragm or an ionic membrane electrolytic cell in which a thin anodic cell lying between the two cathodes, ( 2 ) using an iron anode that has larger specific surface area, ( 3 ) keeping suitable concentration of naoh in the anodic cell, adoption of lower current density and higher electrolyzing speed. the practical technique parameters follow a s below : the naoh solution of 14 - 16mol / l, the temperature of 303 - 308k, the surface anodic current density of 300a / m2, the unit electrolyzing speed of efficiency larger than 6. 0a / l

    快速電解獲取高濃度na _ 2feo _ 4溶液的方法，主要包括四個方面：採用兩陰極室夾一厚度較小的陽極室的隔膜（或離子膜）電解槽；使用比表面積較大的鐵網陽極；保持陽極室中有適宜濃度的濃naoh溶液；採用較低的電流密度和較高的電解速度。具體工藝參數是： 14 16mol / lnaoh溶液、溫度303 308k 、表觀陽極電流密度300a m ~ 2 、有效單位電解速度6 . 0a / l 。
  6. The most important aim of this forum is providing information and opportunities for private enterprises, accelerating the enterprise transformation, promoting the international communication and cooperation of new power to a new step, as a leading orator, our board chairman expressed his particular opinions on " grasp the chances, adjust resource, sostenuto improve the core competition of our company among the new power field "

    4高功率mh ni電池的研究和改進從sc和d型電池入手，對其高功率放電性能和組合電池放電性能加以研究，通過對其正負極材料添加劑隔膜電解液等方面的研究改進，提高其大功率放電性能，進一步適應市場的需要。
  7. In this paper, high concentration vanadium electrolyte has been prepared by electrolysis, graphite and graphite felt electrode also have been made, moreover, the electeodes have been activated, and based it, a lab - level vanadium battery has been manufactured. cyclic voltammetry, current step and invariable current charge / discharge method have been used to study the reactive mechanism of electrolysis, of vanadium electrode reaction and of electrode activation, also to investigate maiden charge process and electricity performance of vanadium battery. the influence of electrode activation and trace stibium ion, indium ion added into vanadium electrolyte has been discussed

    利用循環伏安法、恆電流階躍法、恆電流充放電循環等電化學方法，探討了電解法制備釩液流電解質的反應機理，考察了釩的電極反應、電極表面活化處理對釩的電極反應的影響，結合電極反應分析了活化的機理；還考察了釩電池初次充電活化過程及恆流充/放電循環的電性能；並且考察了添加銻離子、銦離子對釩電池電性能特別是析氫行為的影響。
  8. Because f - doped increases the content of mn3 +, which is the active ion at oxido - reduction, so f - doped can increase the initial capacity, but the increased mn + intensified the jahn - teller distortion and the dissolution of mn2 +, both of which deteriorated the cyclability

    表面修飾后的limn _ 2o _ 4晶粒具有良好的抗電解液溶蝕能力， mn的溶解量僅是未經表面修飾材料的1 / 2左右；雖然首次放電容量有所降低，但其循環性能優良。
  9. It was reported that the mechanism of lithium intercalation into or deintercalation from graphene crystal lattices only explained the interaction with the electrolyte, li - ion and electrode material that exists only on the surface of graphite

    文獻報道嵌鋰石墨嵌脫鋰離子及充放電機制只停留在電解液與鋰離子在電極表面和電極材料間的相互作用。
  10. The results were shown as follows : ( 1 ) the electrolyte components for electroplating pb - sn coatings in fluoborate system were studied. the effects of concentrations of main salt, dissociative acid, inhibitor, antioxidation and surfactant on the cathode polarization curves of electroplating pb, sn and pb - sn alloys and contents of alloying element were investigated systematically. the scale of current density was confirmed using hull cell

    （ 1 ）研究了氟硼酸體系電鍍pb - sn合金鍍層的電解液組成，詳細討論了主鹽濃度、游離酸濃度以及阻化劑、抗氧化劑、表面活性劑等添加劑對氟硼酸體系電沉積pb 、 sn及pb - sn合金陰極極化曲線的影響和對pb - sn合金鍍層中合金含量的影響。
  11. Aluminum products with shing uniform surface was prepared by electrochemical graining process, including alkaline cleaning, 1 % naoh etching, electrochemical roughing in hcl, naoh treating and anodizing in 5 % h2so4 etc

    摘要研究了鋁材無掛灰電化學砂化處理工藝。以鹽酸作為電解液的主成分，控制合適的電流密度和電解時間等工藝參數，通過6步處理，得到砂化均勻、粗糙度適中及光亮的砂面。
  12. The significant capacity loss of the spinel limn2o4 during cycling hereby prevents its wider use as cathode materials for lithium secondary batteries. there are two main factors resulting in fading capacity and poor cyclability, one is the jahn - teller distortion of mn3 +, and the other is mn dissolution to electrolyte. the main objects of this paper are to resolved these key problems effecting on the performance of batteries

    針對limn _ 2o _ 4正極材料在電化學循環過程中發生jahn - teller畸變和mn在電解液中溶解這兩個導致容量衰減和循環性能劣化的關鍵問題，分別採用陰陽離子復合摻雜和尖晶石晶粒表面包裹兩種措施，對尖晶石結構limn _ 2o _ 4正極材料進行了改性研究。
  13. The compatibilities of sample a3000 with six kinds of electrolytes were investigated too. the compositions of the solid electrolyte interphase ( sei ) films formed during the first charging process were analyzed by ftir spectra. the relationship between the sei films and the compatibilities of samples with electrolytes was examined

    考察了具有最佳貯鋰結構的a _ （ 3000 ）試樣和六種電解液之間的相容性，利用ftir圖譜對a _ （ 3000 ）試樣在上述六種電解液中首次充電時在炭負極表面所形成的sei （固體電解質中間相）膜的成分和織構進行了分析，研究了試樣和電解液的相容性與sei膜的關系。
  14. The oxidation curve and sem images show that the oxygen evolution at the interface plays a key role in the transition from the compact al oxide layer to the porous membrane

    分孔道的產生說明析氧反應不但在緻密膜電解液界面發生，而且在多孔膜孔壁電解液界面也同時發生。
  15. In this paper, the ceramic coatings were prepared in situ on ti - 6al - 4v alloy by micro - plasma oxidation ( mpo ). the phase composition, microstructure and corrosion resistance of the ceramic coatings were studied in detail and the technology of corrosion resistant coatings was optimized. the dissolution of the substrate and the changes of the elements in the electrolyte during the mpo process were studied to discuss the growing characters and the structure of the ceramic coatings

    本文通過微等離子體氧化（ mpo ）方法在ti - 6al - 4v鈦合金表面原位生長陶瓷膜，系統地研究陶瓷膜的相組成、微觀結構及膜層耐腐蝕性能，並優化耐蝕性陶瓷膜層制備工藝;分析基體在mpo過程中的溶解現象和電解液中離子濃度變化特點，探討電極表面陶瓷膜層生長規律和結構特點;研究膜層的等效電路、膜層結構與耐腐蝕性能的關系，並對優化工藝條件下制備的陶瓷膜層進行進一步的耐腐蝕性能測試和耐腐蝕機制研究。
  16. The interface of electrode / electrolyte exists solid electrolyte interphase ( sei film ) in the lithium - ion batteries. the film has important influence on the safety, self - discharge, capability, low temperature performance, coulombic efficiency and the irreversible capacity of the lithium - ion batteries

    在鋰離子電池中，電極/電解液界面存在的sei膜對鋰離子電池的安全性能、自放電、容量、低溫性能、庫侖效率、循環性能和不可逆容量有重要影響。
  17. The condition of electrolyte preparation, the setup of instrument exporting cv voltage, the influence of co - deposition ir composition, the treatment of ta foil surface and annealing treatment of electrode are studied. the mechanism of ru compound deposition is discussed meantime

    討論了電解液配製條件、儀器使用條件、共沉澱銥化物、鉭基體表面處理和電極片退火處理條件對產品性能的影響，並分析了沉積機理。
  18. The analytic results of the effects on the micromorphological structure of the film by the electrochemical condition ' s showed that the carbon is apt to improve the boundary combination between the scfs and the surface of the cathode and the seperation of the films, and that the micromorphological structure of the mpgcfs is greatly affected by the dring and the power voltage, which remarkably affluence ion move in swelling cathode film, and that higher temperature and concentration of cu2 + in the medium solution are also advanagable to the deposition of cu in scfs. the plot of deformation behavior of mpgcfs showed that the maximum strench ratio decreases and the brittleness increases due to the existence of the metal phase, and that the strengh trend of the composite films is fistly up and down followed with the content of metal phase because of the change of the role of the metal phase from acting as the physical cross - linking to weakening the films due to destroying the whole structure of the polymer

    另外它作為基體的另一個突出的優點是制備的溶脹復合膜（ scf ）中的溶劑與電解液中的溶劑相同都是水，克服了以前膜內外不同溶劑之間擴散的問題，結果使得電流最終趨於一種穩態，因此可以更好實現用電化學條件來控制mpgcf的形態結構；硬質石墨材料的多孔的結構和石墨本身的結構性能特點使得碳作為陰極材料時有利於溶漲復合膜（ scf ）與電極表面的結合以及膜的剝離，因此是作為陰極的理想材料；電化學條件中的乾燥程度和電壓能夠明顯的影響離子在膜內的遷移，從而對mpgcf的形態結構造成較大的影響；而提高反應溫度和增大電解液中銅離子的濃度也有利於銅在膜中的沉積生長。
  19. Once in the polymer, the electrolyte stays there until a newly applied voltage coaxes it out

    一旦電解液被聚合物吸入，那這些液體就得待在裏面，直到新輸入的電壓把它們給排出去。
  20. So it is important to chose the apt electrolyte and it ’ s additive. excellent electrolyte and it ’ s additive will conduce to form the sei film which has steady structure and good performance

    因此，選擇適當的電解液及其添加劑，以保證電解液各組分在電極/電解液界面形成性能優良、結構穩定的sei膜是非常重要的。
分享友人
分享到 Line

分享到臉書