靜壓軸承 的英文怎麼說

中文拼音 [jìngyāzhóuchéng]
靜壓軸承 英文
hydrostatic bearing
  • 靜 : Ⅰ形容詞1. （安定不動; 平靜） still; calm; motionless 2. （沒有聲響; 清靜） silent; quiet Ⅱ名詞（姓氏） a surname
  • 壓 : 壓構詞成分。
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 承 : Ⅰ動詞1 （托著; 接著） bear; hold; carry 2 （承擔） undertake; contract （to do a job） 3 （客套話...
  • 軸承 : [機械工程] bearing; axle bearing; bearing of shafts; gudgeon block; mechanical bearing; pillow; s...
  1. Application of elastic variable - section pressure - equalizing groove in the structural design of high - stiffness aerostatic thrust bearing

    用可變截面均壓槽實現高剛度空氣靜壓軸承的結構設計
  2. Then this thesis apply iterative computation using fluent software, that means fluent is successfully used in the research of porous aerostatic bearing field for the first time

    然後用計算流體力學中的fluent軟體進行迭代計算，成功地將其引入到多孔質靜壓軸承研究領域。
  3. People now pay much attention at porous aerostatic bearing which has obviously higher load capacity and better damping characteristic and stability. there are two kinds of porous aerostatic bearing : the whole porous and partial porous

    多孔質氣體靜壓軸承能明顯提高軸承的承載能力，具有更優越的阻尼特性和穩定性，故得到廣泛的關注。
  4. Radial - thrust floating - ring hybrid bearing, which can not only sustain the radial load but also the axial load, colligate the strongpoints of pure dynamic and static bearings

    徑?推聯合浮環動靜壓軸承自二十世紀七十年代經提出后，已進行了較為系統的研究。
  5. Fig. 4. 16 shows an example of a pressurized bearing installed at liverpool docks.

    圖416示出利物浦船塢裝用的靜壓軸承例子。
  6. Aerostatic bearings have been applied widely on the ultra - precision in the aviation, aerospace and the main axes and the slide of the precision measuring instrument and inertial measuring apparatus because of high rotation accuracy, calm operation, low friction and long life - span etc. they can also be used in fields range from both high and low temperature to both high and low velocity, sometime even to environment full of radioelement

    氣體靜壓軸承回轉精度高、運轉平穩、摩擦小、使用壽命長，可以在極高和極低的溫度、超低到超高的速度下，以及輻射環境中工作，因此在航空、航天領域以及精密測量和慣性測試設備上得到廣泛應用。
  7. The paper was based on load - bearing properties of elementary aerostatic bearing, predigested support and spindle structure of multi - support aerostatic motorized spindle, established finite - element analysis model, analyzed all kinds of structureal designs of shafting refer to ansys software, analyzed and compared load - bearing characteristics

    摘要基於單元氣體靜壓軸承的承載性能，簡化多支承氣體靜壓電主軸的支承和主軸結構，建立了有限元分析模型，藉助ansys軟體分析軸系的各種結構方案，並進行承載特性分析對比。
  8. As one of the four important parts of water hydraulic axial piston pump, the design of sliding shoes friction matching mainly takes hydrostatic bearing

    作為水壓軸向柱塞泵的四個關鍵組件之一，滑靴摩擦副的設計主要採用靜壓支承的方法。
  9. Structural design of hydrostatic bearing for the axial force equilibrium of multistage pump

    平衡多級泵軸向力的液體靜壓支承的結構尺寸設計
  10. The paper also analyzed that different spindle structures and bearing arrangements influenced load - bearing characteristics of motorized spindle, finally obtained excellent multi - support hydrostatic bearing motorized spindle structure

    分析了不同主軸結構和軸承布置對電主軸承載特性的影響，優選出了的多支承靜壓軸承電主軸結構。
  11. A good vibration damping measure is very important for the enhanced working accuracy of machine tools, especially for that of ultra - precision machines. taking the sub - micron cnc ultra - precision turning machining for an example, this paper illustrated the vibration damping design features on configuration and material selecting, and put the emphasis on the vibration analysis of air spring vibration and aero - static bearing spindle. the theoretical analysis and experimental result have proved that the vibration damping measure is practical

    良好的減振措施是提高機床，特別是超精密機床加工精度的重要技術之一.本文以亞微米超精密車床為研究對象，論述了該機床從結構到材料選取上的減振特點，並重點進行了空氣彈簧和空氣靜壓軸承主軸減振分析，由理論分析和實驗表明:減振措施合理，減振效果良好
  12. All above, the test and the theoretical research formed the basis of practical application for the radical - thrust floating ring hybrid bearing

    以上軸承的試驗研究及理論推導為徑向?推力聯合浮環動靜壓軸承的進一步研究和工程應用奠定了基礎。
  13. Fourthly, to give an introduction about the static characteristics experiment, which has the plan, the devices and the methods of experiment and the metering equipment. finally, to process data and make graphs, to contrast experimental results with calculation results and make certain explanations and to come to some conclusions

    最後對徑?推聯合浮環動靜壓軸承靜特性進行測試，對實驗數據進行了處理、繪制了相應的圖表並對試驗結果和計算結果進行分析對比，得出了?定的結論。
  14. Design and analysis of the high - rotating gas bearing test - bed

    高速徑向氣體靜壓軸承試驗臺的設計與分析
  15. Fig. 4. 16 shows an example of a pressurized bearing installed at liverpool docks

    圖4 16示出利物浦船塢裝用的靜壓軸承例子。
  16. The supporting environment of the system is formed with the integrating of apache and tomcat server. after studying the hydrostatic bearings ’ structure, function and design method, several typical and applied hydrostatic bearings and guide rails are selected, so the function of the remote design service comes true by the dreamweaver platform for programme exploiture and the techniques of html and matlab. the method is feasible after debugging

    在上述研究的基礎上，提出了matlabwebsever的遠程設計服務方案，集成了apache和tomcat服務器，形成了系統的支持環境;以dreamweaver為程序開發平臺，採用html和matlab等技術，在研究液體支承的結構、功能和設計方法的基礎上，選取了幾種典型、實用的液體靜壓軸承和導軌，實現了其遠程設計服務的功能，經調試，方法可行。
  17. This paper is a part of the research project named the static and dynamic characteristic research of the radial - thrust floating ring hybrid bearing which is supported by the natural science and technology research foundation of the nation

    本文完成的工作是國家自然科學基金項目「徑向?推力聯合浮環動靜壓軸承靜、動特性研究」中的一部分。
  18. In this paper, based on the theory of radial - thrust floating ring hybrid bearing, the dynamic characteristic test for this kind of hybrid bearing is accomplished on the self - made test stand, the dynamic characteristics of the testing bearing are got, and the dynamic characteristic coefficients of the thrust part of the bearing are measured for the first time, the result of the test is compared with the theoretical calculation

    本文是在徑向?推力聯合浮環動靜壓軸承理論研究的基礎上，利用自製的實驗臺完成了對該軸承的動特性試驗研究，首次得到了測試軸承的動態特性，並將實驗結果和理論計算進行了對比。
  19. Furthermore, the temperature fields of the radial - thrust floating ring hybrid bearing which includes the lubricant inertia item is stud ied for the first time, the reynolds and energy equations are derived, the relationship between viscosity and temperature as well as the boundary condition of pressure and temperature are developed

    此外，本文還首次對考慮慣性項下該動靜壓軸承的溫度場進行了理論研究，建立了數學模型，導出了該浮環動靜壓軸承徑向部分、推力部分的能量方程、雷諾方程以及粘溫關系、壓力、溫度邊界條件等。
  20. My paper attempts to attain some conclusions from this study of gas cavity, and these conclusions may be useful to controlling bearing operation. the oiling system is an important part of radial - thrust floating - ring hybrid bearing. there are some factors that lead to the variation of oil - pressure in the oiling system

    本論文試圖從理論方面研究由於供油壓力變化導致氣穴現象（這時候呈現兩相流潤滑）對徑?推聯合浮環動靜壓軸承動靜態特性的影響，為以後可能尋求主動控製作了準備。
分享友人
分享到 Line

分享到臉書