預浸漬法 的英文怎麼說
中文拼音 [yùjìnzìfǎ]
預浸漬法
英文
prepreg method-
In this paper, the al3 + - doped zno thin films were prepared on na - ca - si glass substrate ( microscope slides ) by sol - gel process from 2 - methoxyethanol solution prepared by zinc acetate as premonitor, monoethanolamine as stabilizator and aluminum chloride reaction. homogenous, transparent, polycrystalline zno thin film was formed finally by diping coating conducted for film - plate on substrate, drying, pre - heat - treatment, anealing
所用的溶膠是以乙二醇甲醚為溶劑,醋酸鋅為前驅體,乙醇胺為穩定劑反應制得,用浸漬提拉法在基體上鍍膜,經烘烤、預燒、退火,最後形成均勻、透明的多晶zno薄膜。Liquid - solid extrusion of composite material is a new kind of metal forming process, which has been developed in recent years with a promising practical application prospect for its simple working procedure, low cost and good workpiece performance. through a lot of experiments, the optimization and chosing method of key process parameters ( pouring temperature, mold warm - up temperature, impregnating pressure, impregnating time ) has been mastered. under the precondition of appropriate chosing these parameters, the effective control of extrusion velocity is the key of mading good workpiece. but the control of extrusion velocity remains a handwork, and it is heavily affected by such uncertainties as a handler ' s knowledge and skill about the process. in order to solve the problem, the automatic control of the extrusion velocity is studied, and a computer control system is also designed under existing condition
通過大量實驗,已掌握了關鍵工藝參數(熔液澆注溫度、擠壓模預熱溫度、浸漬時間、浸漬力)的優化選取方法。在合理選取關鍵工藝參數的前提下,擠壓速度的控制是成形出質量良好製件的關鍵。但是,目前對于擠壓速度的控制仍停留在手動控制階段,利用該工藝制備管、棒材製件的成功與否受操作者對該工藝及其設備的經驗及熟練程度等不確定因素影響很大。Aerospace series. non - metallic materials. resins, adhesives, reinforced plastics, preimpregnates. characterisation by liquid chromatography
航空航天系列.非金屬材料.樹脂粘接劑增強塑料預浸漬劑.用液相色譜法的特性說明Precast concrete products - test method for glass - fibre reinforced cement - determination of the absorption of water by immersion and determination of the dry density
預制混凝土製產品.玻璃纖維增強水泥的測試方法.浸漬時水吸收性的測定和干密度的測定The hot - melt impregnation process of large tow carbon fiber ( 60k ) prepreg to prepare fishing rods is briefly introduced in this paper ; in addition, several typical factors which affect the quality of the prepreg are also discussed in detail here
摘要本文簡要介紹了釣魚竿用大絲束( 60k )碳纖維預浸料熔膠膜法浸漬工藝,並著重就影響預浸料質量的幾個主要因素進行了討論。Standard test method for resin solids content of carbon fiber - epoxy prepreg
碳纖維環氧樹脂預浸漬中樹脂固定含量的標準測試方法Textile glass fibre preimpregnates - test method for the determination of the resin flow
紡織玻璃纖維預浸漬.測定樹脂流動的試驗方法Textile glass fibre preimpregnates - test method for the determination of mass per unit area
紡織玻璃纖維預浸漬.測定單位面積質量的試驗方法Textile glass fibre preimpregnates - test method for the determination of the content of volatile matter
紡織玻璃纖維預浸漬.測定揮發物含量的試驗方法Aerospace series. textile glass fibre preimpregnates. test method for the determination of the resin flow
航空航天系列.預浸漬玻璃纖維織物.測定樹脂流的試驗方法Aerospace series. textile glass fibre preimpregnates. test method for the determination of mass per unit area
航空航天系列.預浸漬玻璃纖維織物.測定單位面積質量的試驗方法Aerospace series. textile glass fibre preimpregnates. test method for the determination of the content of volatile matter
航空航天系列.預浸漬玻璃纖維織物.測定揮發物含量的試驗方法Textile glass fibre preimpregnates - test method for the determination of the resin and fibre content and mass of fibre per unit area
紡織玻璃纖維預浸漬.測定單位面積樹脂纖維含量和纖維質量的試驗方法分享友人