預燒 的英文怎麼說

中文拼音 [yùshāo]
預燒 英文
fore fire
  • 預 : Ⅰ副詞（預先; 事先） in advance; beforehand Ⅱ動詞（參與） take part in
  • 燒 : Ⅰ動詞1 （使東西著火） burn 2 （加熱或接觸某些化學藥品、放射性物質等使物體起變化） cook; bake; hea...
  1. Beryllium powders with the same particle size and various contents of beo were prepared by pre - sintering - acid washing processes initiatively and the influence of beo alone on o mys of beryllium was observed and some new results have been obtained - compared with the content of beo, the distribution of beo in beryllium has more critical influence on mys ; finely dispersed beo along the grain boundaries and in the matrix results in the dispersion strengthening of beryllium matrix and thereby the higher mys value ; on the contrary, the coarser beo particles clustering on the grain boundaries results in negative influence on o mys

    開創性地用預燒結? ?酸洗工藝制備了相同粒度、不同beo含量的鈹粉，從而開展了beo含量單獨對鈹材_ （ mys ）影響的研究，得出一些新的結果：與beo含量相比， beo在鈹中的分佈狀態對_ （ mys ）的影響更大。沿晶界、晶內彌散分佈的較細小beo對基體鈹有彌散強化作用，使_ （ mys ）即較高；如果beo較粗大地成簇狀聚集在晶界，反而對_ （ mys ）有不良的影響。
  2. To meet the processing requirements before sintering, the pressed briquet was pre - calcined at 1150 to make it possess adequate processing strength at first and then was shaped through precise turning on the numerical control lathe according to the design diagram of the femoral head prostheses of partial hip joint

    為滿足燒結前坯體加工的要求，壓制后的坯體在1150預燒，使其具備一定的加工強度，然後按照半髖關節股骨頭假體的形狀尺寸設計圖在數控車床上進行精密車削成型。
  3. In this paper, the al3 + - doped zno thin films were prepared on na - ca - si glass substrate ( microscope slides ) by sol - gel process from 2 - methoxyethanol solution prepared by zinc acetate as premonitor, monoethanolamine as stabilizator and aluminum chloride reaction. homogenous, transparent, polycrystalline zno thin film was formed finally by diping coating conducted for film - plate on substrate, drying, pre - heat - treatment, anealing

    所用的溶膠是以乙二醇甲醚為溶劑，醋酸鋅為前驅體，乙醇胺為穩定劑反應制得，用浸漬提拉法在基體上鍍膜，經烘烤、預燒、退火，最後形成均勻、透明的多晶zno薄膜。
  4. It has been found that all the elements in the addition act respectively in the way that affect the material ' s properties during the calcining process and the increase of the pms / pzn ratio can weaken the stability of the crystal structure of the sintered ceramics and cause the crystal structure transformation from the tetragonal to the rhombohedral as well

    發現多元壓電陶瓷材料中，無論是主加組元還是微量摻雜，預燒階段，它們在陶瓷中的作用都表現為單獨離子對陶瓷結構和性能所起的作用。燒結后，隨著pms pzn相對量的提高，陶瓷晶體結構由四方相向三方相轉化，同時穩定性下降。
  5. Meanwhile, based on the magnetic material theory, a complete analysis and summary are carried out on the three crystal structure and technology theory ; especially the ingredient analysis is made on the microscopical morphology and x - ray diffraction and its mixtures existence and relevant metallurgy about the typical second resource such as coldrolling iron and oxide red, steelmaking sludge and feso4 based on the practeal investigation of the pre - burning materials in domestic products plant, especially the analysis on the domestic markets and components, and connecting with reality and material characters in panzhihua iron and steel ( group ) cmpany, we established the product orientation and developing direction in panzhihua iron and steel ( group ) company ; after carrying out the technology reform on the old no. 1 magnetic product plant of enterprise company, making a detailed study on the various conditions for establishing a plant, the feasible research report is formed of 1400 tons ( per year ) feo preburning material and 3000 tons ( per year ) middle and high quality magnetic products ; so a necessary and reliable supports are provided both theoretically and practically for the development of the magnetic industry in panzhihua iron and s teel ( group ) cmpany

    同時，對磁性材料的理論基礎，尖晶石、磁鉛石、石榴石三大晶系結構以及其工工藝理論進行了較為全面的歸納、分析和總結；尤其針對攀鋼產生的二次資源如冷軋鐵紅、煉鋼污泥、硫酸亞鐵等三種典型原料分別作了成分分析、微觀物理形態以及x光衍射分析、其夾雜物的存在形式及相應的金相分析。對國內鐵氧體磁性材料的預燒料及磁件生產廠家的工藝、設備、技術、成本、質量狀況進行了實地的調研，特別是對國內磁性材料的市場及競爭對手進行了詳盡的分析，在此基礎上，結合攀鋼實際及原料特點確立了攀鋼發展磁材產業的產品定位及發展方向；對企業公司原有磁件一廠進行了技術工藝改造，對建廠各項條件進行了詳細的分析，形成了了年產14000噸年鐵氧體預燒料以及3000噸年中高檔磁件產品的可行性研究報告，從理論上和實踐上為攀鋼磁性產業的發展提供了必要的可靠的依據。
  6. On the base of the analysis on the advanced technology of hard ferrite in foreign country, the main procedures of preparing hard ferrite pre - sintering material are determined as follows : first, the ferrite oxides coming from the main cold rolling line and strontium carbonate are conveyed to storage tank by gas power and weighed automatically according to the demands of constituent composition. and then they are mixed and grinded by using method of wet treatment. finally the mixtures is transported to the devices of storage by transporting pump

    在分析國外先進的永磁鐵氧體生產工藝的基礎上，確定了生產高檔永磁鐵氧體預燒料的主要過程：首先，利用攀鋼冷軋鐵紅為主要原料，將氧化鐵紅及碳酸鍶採用氣力輸送至貯料料倉，經自動稱量裝置，按工藝配方稱量後分別由氧化鐵紅及碳酸鍶發送罐氣力輸送進入預混攪拌筒加水攪拌，然後再送入混磨機濕法混磨；最後，混合物經輸送泵輸送至料漿存儲裝置，經定量進料泵定量輸送至回轉窯進行濕法預燒，預燒料經緩冷至室溫后，再球磨。
  7. The raw materials, the composition, the time of milling, the calcining temperature, the different additives, the sintering temperature and the sintering parameters were investigated. the result showed : it was advantaged to obtain high initial permeability mnzn ferrite with stable frequency characteristic using high - purity raw materials ; in order to obtain mnzn ferrite with high properties, we must control strictly the composition ; it could improve the properties of mnzn ferrite by optimizing calcining temperature. the lower calcining temperature made the permeability higher, and the higher calcining temperature could promote the frequency characteristic of permeability ; we chosen the right time of milling according to the requirement of power diameter ; in order to improve the properties of mnzn ferrite, it is necessary to add effective additives. in this dissertation, the influence of bi2o3 、 moo3 、 k2co3 、 co2o3 were investigated ; the sintering temperature, the time of heat - retaining and sintering parameters were the key factors of preparing high permeability mnzn ferrites

    研究結果表明:採用高純度的fe2o3有利於獲得高起始磁導率且頻率特性優良的鐵氧體;為了制備所需性能的鐵氧體，需要嚴格控制配方中各種原材料的含量，優化配方;由於粉體活性受預燒條件的影響，所以對不同要求的鐵氧體選擇的預燒條件就不一樣，適當降低預燒溫度有利於獲得較高的起始磁導率，而為了獲得良好的頻率特性可以適當地提高預燒溫度;根據對粉體顆粒粒徑的不同需求，可以選擇不同的球磨時間;而有效的添加劑是改善材料性能的必要條件，本文在添加劑的研究中主要對bi2o3 、 moo3 、 k2co3 、 co2o3的影響分別作了詳細地討論;燒結溫度、保溫時間和燒結氣氛是高磁導率mnzn鐵氧體制備最關鍵的工藝，適宜的燒結工藝可以獲得理想微結構和組成，從而得到高性能的鐵氧體材料;而從材料的微結構上來看，要提高材料的截止頻率，就要適當地細化晶粒、增加晶粒內部的氣孔。
  8. The research work in this paper was carried out at the second power factory of xici subsidiary. the production technology of strontium ferrite was studied and wet process of strontium ferrite pre - sintering material with anisotropic characteristic was determined. products of y30h - 2 which meet the standard series of sj / t10410 - 1993 were selected to be experimental products

    本文以西磁分公司料粉二廠為基點，研究了鍶永磁鐵氧體生產的工藝技術路線，確定了濕法工藝生產各向異性鍶永磁鐵氧體預燒料，並將試驗產品定位在sj t10410 - 1993標準中的y30h - 2產品。
  9. In order to make use of labor power, material resources, financial resources, financial resources and natural resources in the panzhihua iron and steel company, to develop the district of high - grade magnetic material and establish magnetic material industry production base in the west region of china, this paper focus on the study of the application technology of hard ferrite pre - sintering material with high - quality

    為充分利用攀鋼現有人力、物力、財力及得天獨厚的自然資源優勢，發展地區高檔磁性材料產業，建設中國西部磁性材料產業基地，本文對高檔永磁鐵氧體預燒料制備應用技術進行了研究。永磁鐵氧體特別是高性能永磁鐵氧體材料是當代社會及其發展的基礎功能材料。
  10. Limnoa has been synthesized from self - synthesized material y - mn203 by wet moist chemical method under different sinter conditions in argon. the material was analyzed by xrd, sem. it is shown by xrd that material is limno2 single phase in 450 keeping 5h, then in 600 ? sintering 6h in argon

    通過xrd物相分析發現:以自制原料y一mnzo3為錳源，在a :氣保護下，採用濕化學法，在450下，預燒結5h研磨后再於600下燒結6h ，可以合成出單相limnoz 。
  11. The sintering between tic powders can make the tic preforms with network structure

    熱壓法集預制體成型和預燒結於一身，成功率高。
  12. The preparing process is as follow : mixing the nickel salt, zirconium salt and stabilizer in the solvent ( distilled water ) to prepare mixing solution according to a certain ratio ; commingling the mixing solution and coordination solution of carboxylic ammonia in accordance with a certain rate to form sol, drying the sol and turning it into gel, pre - sintering the gel to get the zro2 - nio powders and the zro2 - ni nanocrystalline composite powders were gained by reducing the zro2 - nio powders

    方法如下：將鎳鹽、鋯鹽、穩定劑和水溶劑按所需成分配成混和溶液，再將混和溶液、外加劑按比例混和形成溶膠，溶膠經乾燥成為凝膠，凝膠經預燒得到ysz - nio氧化物納米粉末，將該氧化物粉術還原得到ysz - ni納米復合粉術。絡合。
  13. In this study, the preparing processes of zro2 - ni nanocrystalline composite powder aremixing the nickel salt, zirconium salt and stabilizer, solvent ( distilled water ) together to prepare the mixing solution according to certain ratio ; commingling the mixing solution, coordination solution of carboxylic ammonia, intrusion aid in accordance with certain rate to form sol, drying the sol and turning it into gel, pre - sintering the gel to get the zro2 - nio powder and gaining zro2 - ni nanocrystalline composite powder by reducing the zro2 - nio powder. xrd, x - ray wide - angle diffractometer, bet, sem, tem, hrtem analyses are used to study the zro2 - ni nanocrystalline composite powder and zro2 - ni cermet. the sintering temperature is determined

    本研究的zro _ 2 - ni納米復合粉末的制備方法如下：將鎳鹽、鋯鹽、穩定劑和溶劑（水）按所需成分配成混合溶液，再將混合溶液、外加劑和氨羧絡合劑按比例混合形成溶膠，溶膠經乾燥成為凝膠，凝膠經預燒得到zro _ 2 - nio納米粉，將該氧化物粉還原得到zro _ 2 - ni納米復合粉。
  14. Prepared technical parameters were optimized by l9 ( 34 ) experiment analysis. a unique method for cleaning and drying of substrate - cleaning used by scour, drying used by infrared light was fished out by large numbers of experiment. chemical mechnism of zno thin film prepared by sol - gel technique was discussed by dta for the first time. by the measurements of sem, xrd and uvs, the thin film was analysed. the result proved that the thin film with strongly preferred orientation of c - axis perpendicular to the substrate surface which surface was homogenous, dense and crackfree was the crystalline phase of hexagonal wurtzite. the thin film was composed of plentiful asteroidal crystal which crystal dimension approximately 10 30nm. the average transmittance of thin film in visible region was above 90 %. the results of measurements else also proved that the thickness of single dip - coating was 75 240nm, this films resistivity was found to be 3. 105 102 3. 96 105 ? cm. the thickness and resistivity of thin film influenced by dope - content, withdrawal speed, pre - heat - treatment, anealing were reseached respectively

    利用xrd 、 sem以及uvs光譜儀等分析方法對薄膜進行了研究，結果顯示，所制備的薄膜為六方纖鋅礦型結構，具有高c軸擇優取向性；表面均勻、緻密，薄膜材料由許多星狀晶粒組成，晶粒尺寸大約為10 - 30nm左右；薄膜可見光透過率平均可達90 % ；對薄膜厚度以及電學性能進行了測定后發現：單次鍍膜厚度約為75 - 240nm ， al ~ （ 3 + ）離子摻雜型氧化鋅薄膜的電阻率在3 . 015 102 - 3 . 96 103 ? cm范圍內；分別研究了摻雜濃度、提拉速度、預燒溫度、退火溫度等工藝參數對薄膜厚度和電阻率的影響。
  15. After prep - baking and making - granule, under different temperature we baking on the preceding powder, and it proof the most proper baking temperature is 1440. under 1440, we do the excessive zinc oxide experiment, and find when zinc oxide excessiving3 %, we can get the best production which i is 5962

    將制備得到的前驅粉在850 2 . 5h條件進行預燒、制粒后，在不同焙燒溫度下進行了鐵氧體焙燒試驗，並對最優配方下zno過量條件進行試驗研究。結果表明，在焙燒溫度1440 ， zno過量3 %的條件下，可制得i為5962的高磁導率鐵氧體。
  16. Formulating the batch scheduling in semiconductor burn - in operations as a mathematical programming

    大規模集成電路預燒作業中分批排序問題的數學模型
  17. After dry gelation is calcined at 400, nanometer powder with low sintering temperature and great performance can be successfully prepared

    將干凝膠在400預燒就可以獲得性能優良的納米粉。
  18. The researches indicate that after a heat treatment at high temperature ( 1700 ? ), the chemistry properties of the boron carbide surface are changed. the new boron carbide surface, react weaker with aluminum, thus a better infiltration can be achieved

    碳化硼預制體經高溫預燒后，碳化硼表面化學狀態發生改變，預燒后形成的碳化硼新表面與鋁的反應活性降低，從而保證在本文工藝條件下浸滲過程的順利進行。
  19. Combined core - shell method with scm, pmw - pnn - pt ceramics with core - shell structure, which have excellent dielectric temperature stability, were successfully prepared. the new mechanism of improving temperature stability of dielectric properties was put forward. the main contents are lis ted as bellows : in the systems of pmn - pt, the effects of the chemical reactivities of the starting materials such as soluble mg - salts instead of mgo, pb - salts instead of pbo and ti ( oc4h9 ) 4 instead of tio2 respectively on the formation of perovskite phase were investigated in detail

    Scm法與cpm法的工藝相比，工藝簡單，預燒溫度和燒結溫度低，反應時間短；陶瓷緻密，介電性能比cmo法和cpm法明顯得到改善，而且在沒有pt存在時，仍可制得純鈣鈦礦結構的pmn基、 pnn基、 pfw基陶瓷。
  20. The optimized preparation conditions were pre - sintering temperature of 910, sintering temperature of 1100 and keeping temperature duration for 6 hours. for sno _ 2 ceramic target, the optimized preparation conditions were pre - sintering at 1100, sintering at 1500 and keeping temperature duration for 6 hours

    其最佳工藝條件為: 910預燒， 1100燒結並保溫6小時;而制備透明導電薄膜sno _ 2陶瓷靶材的最佳工藝條件為:預燒、燒結溫度分別為1100和1500同時保溫6小時。
分享友人
分享到 Line

分享到臉書