顯式通信 的英文怎麼說
中文拼音 [xiǎnshìtōngxìn]
顯式通信
英文
explicit communication-
After the switching of the numbering mode, services can be displayed and configured on the basis of lucent s numbering mode. but at that time since there was no network - level nm in beijing telecom s transmission network and the lct ( pc - based element - level nm ) could display and configure services only on the basis of huawei s mode, the configuration mode needed to be modified manually when implementing interconnection to lucent s equipment and each adjustment had to be made according to lucent s numbering mode through the built - in cross connection function while configuring services
轉換后，即可按朗訊的編號方式在網管上顯示業務與配置業務。但當時北京電信的華為傳輸網未建立該網路級網管，而lct （基於pc的網元級網管）只能以華為公司的時隙編號方式顯示與配置業務，在與朗訊對接時需要人工修改配置方式，通過sdh設備的內置交叉功能在配置業務時按朗訊公司的編號方式一一調整。Using domestic strained integrated resistor as weighing sensor, at89c52 single chip as control unit, combined with arithmetical magnification, analogtodigital conversion ( a / d ), real time clock, liquid crystal display ( lcd ), and series communication interface, a minitype automatic weighing lysimeter is developed. that made measurement of evapotranspiration become conveniently and effectively in studying on water use of crops
為了方便、有效地測定植物的蒸散，為水分利用研究提供價廉物美、簡單易用的儀器，本研究利用國產的集成電阻應變式稱重傳感器，採用at89c52單片機作為控制單元，結合運算放大、模數轉換、實時時鐘、液晶顯示、數據存儲、串列通信等外圍介面電路，研製了小型自動稱重式蒸散儀。In the hardware design, the paper completes modules ’ design like outside memory, patulous a / d, patulous d / a, rs232 communication, ecan communication, led control, keyboard control, distant control, emulation, reset, logic voltage switch, dsp supply power regulate and ac - dc power circuit, as well as room layout design like anterior panel, back panel etc. and dsp transfers data with peripheral equipments except outside memory using serial ports. besides, the whole circuit is configured in interrupt response. thus, it can meet system demand as well as take full advantage of tms320f2812 ’ s hardware resource. in the software design, the paper finishs programs like the interface programms intercommunicates with people, the distant control program, ad and da modules ’ control program, in addition, the paper select the velocity and acceleration state - feedback algorithm and is written in the program. the software design uses dsp integrate exploiting environment named ccs2. 2 of ti inc. as software instrument, and programs with the combination of c language and assembly language. moreover, in order to maintenance or modify the software expediently and shorten software ’ s exploitation time, the design adopt software modularization technique. finally, some air cylinder experiments are carried out to proved that the pneumatic controller is very practical
在硬體設計中，本文完成了片外存儲器擴展、 a / d擴展、 d / a擴展、 rs232通信介面、 ecan通信總線介面、液晶顯示控制、鍵盤控制、遠程控制、模擬、復位、邏輯電平轉換、 dsp工作電源校正電路和ac - dc電源等模塊設計以及控制器前面板、後面板等的空間布局設計。其中dsp與除外部存儲器的外圍設備之間的數據傳送全部採用串口通信，同時系統電路配置成中斷響應方式，這樣既滿足了系統要求，又充分利用了tms320f2812的硬體資源。在軟體設計中，本文完成了人機界面功能模塊、遠程控制模塊、 ad擴展模塊、 da擴展模塊、速度和加速度狀態反饋的控制演算法的程序設計。It integrates the functions of servo amplifier, dynamic operator, position transmitter and remote communication. many new functions have added to its original ones, such as the real - time logical judgment, malfunctions self - diagnosis, alarm & protection, led display, on - line setting and adjustment of functional parameter and position transmitter, power - absence data auto - protection, watchdog system protection, and the long - range communication with pc
系統集伺服放大器、電動操作器、位置發送器及遠程網路式通信功能於一體，在保留對應部分原有功能的同時，還新增了邏輯實時判斷、故障實時監控、 led動態顯示數據、功能參數設置、掉電數據自保護、 「看門狗」電路保護、位置發送器在線調節、與遠程工控機數據通信等眾多功能。Some features of this chip are listed below : firstly, it opts for ir data transmit technology, so it have the advantages of little emi, simple operation, low cost, etc. secondly, the synchrony method makes it have good noise suppression and ber quality
該「紅外名片交換專用晶元」能獨立完成名片交換和管理的任務，具有顯著優點： 1採用紅外數據通信的方式，具有技術方案成熟，交換方法簡單，保密性好，相互電磁干擾小，成本低、簡單易用等優點。The circuit is used in high resolution resistance measuring. the coupled chaotic circuit array composed of this circuit is researched by computer simulation and circuit experiment. results show that, it is feasible to improve the stability of orders of chaotic systems and reduce noise in measuring by coupling
最後，對以這種單電源驅動的混沌電路為基本單元所構成的耦合混沌陣列在提高系統輸出的穩定性和抑制噪聲作用方面，進行了計算機模擬研究和實際的電路實驗研究，結果顯示通過耦合的方式，可以將信號檢測的精度提高近一個數量級。The system uses the embedded microprocessor s3c44b0x to control the sensor to gather water data, then processes, saves and displays them. at the same time it waits to be connected with pc at the control center, receives command - string, then uses modem to send the corresponding data with predefined communication protocol to pc through pstn
測點通過嵌入式微處理器s3c44box控制傳感器採集水位數據，處理后保存並顯示；同時等待與控制中心的pc機建立連接，並根據接收的命令將相應的數據按照預先約定的通信協議，通過modem經公用電話網傳送到控制中心。The safety of transmission line plays a important role in power system safety it is not only the requirement of ensure supply power reliability, but also the necessary precondition of enhance power system stabilization, to remove faulty line quickly and accurately, also keep non - faulty line continuous work when some transmission line faults current differential protection is a kind of simple, reliable and good - selective protection manner to any variety of transmission lines, power system development needs current differential protection apply to transmission lines, moreover the advancement of electric and communication technology enable current differential protection apply to transmission lines firstly, the paper discusses, analyses the research and application transmission line protection in detail, compare the principle and realistic presupposition of general line pilot protections secondly, because conventional current vector differential protection are influenced easily by load current and transitional resistance, in order to at the same time quicken protection act, the principle and criterion include work characteristic of differential protect based on fault component sampled values are studied, results shows that differential protect based on fault component sampled values excels general vector current differential protection in reliability, sensitivity and anti - saturation of current transformer in addition, synchronous current sampling methods at all terminals of line is analyzed and estimated lastly, the principle and criterion. also device design about current sampling values differential protection based on optical fiber communication, which apply to short transmission lines are concretely investigated,
基於基爾霍夫定律的電流差動保護無論對於何種形式的輸電線路都是一種簡單、可靠、選擇性強的保護形式，電力系統的發展使得電流差動保護應用於線路保護成為需要，而電子、通信技術的發展使得電流差動保護應用於輸電線路成為可能。首先，本文對目前線路保護的研究和實際應用情況進行了討論和分析，比較了常用線路縱聯保護的實現原理和實現條件及優缺點。其次，針對常規相量電流差動保護易受正常負荷電流和故障過渡電阻影響的缺點，同時為加快差動保護的動作速度，對基於故障分量瞬時采樣值電流差動保護的原理、判據、動作特性等作了討論和分析，結果表明基於故障分量瞬時采樣值電流差動保護在可靠性、靈敏度、抗電流互感器飽和方面明顯優于常規相量電流差動保護，對電流差動保護各端的同步采樣方法和數據通信也進行了分析和評價。Through analysising the characteristics of the power system with floating neutral point deeply, the paper puts forward a new plan of single - phase to ground fault line selection on the base of s ' s signal injecton method and gives the hardware and software design. in this design, the high speed sampling and data processing is carried out through using dsp processor ; the large electrice current is drived through the application of a high - performance audio power amplifier and transformer ; the communication between host computer and detectors is realized through rs485 bus technology ; the difference multilevel frequency - selected amplifier is designed and the feeble signal of space is sampled on the base of the theory of magnetic induction ; the interface between dsp and exterior chip and rs485 interface logical is designed through using fpga ; the using of lcd module and keyboard interfacing chip makes the interface between human and machine ; the programme of host computer and detectors is designed through using blocking design method
在本設計中，採用高速的dsp處理器，實現了對故障特徵信息的高速採集與處理;採用大功率的功放晶元與變壓器配合的方法，實現了大電流信號的驅動輸出;採用485總線技術，組建了裝置主機與多探測器之間的主從式通訊網路，實現了多干擾條件下裝置主機與多探測器的可靠通訊;設計了差分式多級選頻放大電路，採用磁感應的方法實現了對空間微弱信號的接收;利用fpga技術，實現了控制器與多外設的介面及數字信號的串並轉換;採用了先進的lcd液晶顯示模塊及鍵盤介面晶元，設計了人機信息交互的介面;採用了模塊化的軟體設計方法，開發了裝置主機及探測器的軟體程序。Based on the advanced embedded computer and network technology along with the embedded operational system such as windowsce, the instruments can gather many functions such as transmitting and measurement, compensatory computation, signal analysis and processing into one instrument. in this paper a portable instrument for vibration measurement with embedded computer system was discussed. based on windowsce real - time operation system the software of this instrument was designed and developed with evc computer language
本文基於目前流行的便攜式儀器的核心技術? ? windowsce ，設計開發了應用於現場設備振動測量分析的的便攜式測振儀表，針對現場特點和實際要求，對于測振儀的硬體系統進行了規劃設計，並重點對于儀器軟體進行開發，在windowsce平臺下，利用evc語言開發研製了儀器的應用軟體，實現了包括信號採集、分析、顯示、數據存儲和通信功能的軟體系統；並對該軟體進行了計算機模擬調試。The paper lays a strong emphasis on discussing the realization of the autocontrol of raster scanning of the scanner in x - y dimension, the " tapping " of the cantilever of the tappingmode afm by a direct digital synthesizer. then a method of parallel communication between dsp and pc in epp mode is given. finally, the author discussed the digital pid closed loop control of the scanner in z - direction, the automatic approaching of the tip using step - motor, and also some electro - magnetic interferences
論文首先簡單介紹了掃描探針顯微鏡的發展、分類、工作原理及應用；接著對ti公司的tms320vc5402dsp的特點及外圍擴展作了簡單介紹；然後分章節重點講述了利用vc5402dsp實現掃描探針顯微鏡的核心部件? ?壓電陶瓷管的x向和y向的光柵掃描控制；藉助直接數字集成器（ dds ）實現輕敲式原子力顯微鏡的微懸臂的「輕敲」 ； vc5402dsp的主機介面（ hpi ）與pc機在增強并行口（ epp ）模式下的通信；論文最後還介紹了掃描管z向的數字pid閉環控制，步進電機的自動進針，並對實際出現的一些電磁干擾問題作了討論。By the way, a displaying system and a communicating system is added. this dissertation is divided into four chapters altogether : chapter one is the introduction, introducing the hore component and its important characteristic and putting forward the basic task ; chapter two introduce the principle of the auto - tracking system and respective parts of the auto - tracking system ; chapter three introduce the applications of auto - tracking system under static condition and dynamic condition and give out the experiment results ; chapter four introduced the displaying system, communicating system and the applicability of the auto - tracking system to other sensors
本文共分為五章：第一章緒論中，介紹了霍爾元件及其一些重要特性，並提出了測量系統的基本方案；第二章詳細介紹了測量系統各部分的構成及原理，特別是對直流通道、溫度補償模塊和音圈電機為核心的隨動機構的論述；第三章介紹了實際系統在靜態測量和動態測量兩種模式下的應用及實驗結果；第四章介紹了系統的顯示功能和遠程通信功能並討論了系統對其它傳感器的適用性。It realizes the functions of storing and transferring the information of fire alarm, displaying time, scanning keyboards, the safe maintenance of system and so on. the part of wireless communication is controlled by at89c2051 mcu, mainly realizing transmitting and receiving data between controller and other detectors. the external signals received by a wireless module are transmitted to mcu through shaping circuit, and the signals of mcu are transmitted by a wireless module through tone modulation circuit
人機交互部分以單片機c8051f020為核心，為用戶提供一個良好的操作環境，實現了火災報警信息的存儲及調用、時間的顯示、鍵盤的掃描、系統的安全維護等功能;無線通信部分由單片機at89c2051來控制，主要實現控制器與其它探測裝置之間信號的無線發射和接收，無線通訊模塊接收到的外部信號經過整形電路送入單片機，單片機發出的信號經過音頻調制再由無線通訊模塊發送出去，這樣實現了數據的無線傳輸;本文還從節能的角度出發，兼顧性能的可靠性，提出了一種合理的無線火災報警的信息傳輸模式。Bringing into play the communication market resources in hangzhou bay, the park devotes itself to the formation of a “ mobile valley ”, which means a unique zhejiang - flavored economic pattern : forming a complete telecommunication industry chain from software and operation development of key parts, such as ic chip, rf modules, base band, display, high capacity battery, to related components like cell phone housing, keypad, antenna, vibration motor, mould, pcb ( circuit board ), photoelectricity device, electronic device, connectors and system and software development, and operation service development
園區依託杭州灣通信市場資源，致力打造「移動谷」 ，創造中國浙江經濟特有的專業版塊模式：從集成電路晶元、 rf組件、基帶、顯示器、高能電池等核心器件到接手機外殼和按鍵、天線、振動馬達、模具、 pcb （電路板） 、光電器件、電子器件、連接件等相關組件及系統和軟體開發、運營服務開發，形成完整的通信產業鏈。Plc, robot and cad / cam are called the three major pillars in the modem factory automation. plc, as the head of the three, has become the leading basic automatic equipment in the field of the industry control in the early 1980s " but as a matter of fact, plc being with the lack of friendly man machine interface, rnakes no close relationship between human and machineometimes it even can not be promoted and applied in some fields aiming at the situation mat those imported products are too expensive while domestic products are of rare famous brands, a plc man - machine interface - plc monitor is developedthis paper systemically introduces the developing procedure for the whole system, including how to design hardware and software system. especially emphasizing plc communication protocol. real time message accessing, lcd controller instruction set, definition of data construction for message & tag screens and how to display thern, assignment of internal resource of cpuealization in software among plc & manitor, file format defining a nd download of user data, etcplc monitor will compensate some weakpoints of plc, and extend the application rangeimultanneously enhance the performance of plc and increase the attached value of mechanical machines, undoubtedly it will see hight market prospect
針對人機界面進口產品的高昂價格和國產品牌稀少的這一現狀，研製開發了一種plc人機界面? plc監控器。本文系統地介紹了整個系統的開發過程，包括硬體系統、軟體系統的設計及實現，重點介紹了plc通信協議，監控器的基本工作原理以及期望實現的功能，監控器電源電路、 sram存儲器掉電保護電路、 cpu監控器電路、按鍵輸入電路的設計及按鍵狀態的讀入，時鐘信息的設定與讀取， cpu液晶顯示器指令系統，信息畫面及標簽數據結構的定義及顯示方法， cpu內部資源的分配，監控器與plc通信的軟體實現，文件格式的定義以及畫面數據的下載等。 plc監控器彌補了plc一些方面的不足，可以擴大plc的應用范圍，提升機械設備的檔次，增加設備的附加價值，具有一定的市場前景。According to its uses, lcd panel can be classified into 9 categories such as communication, domestic electrical appliance, palm computer, transportation means, measuring apparatus, meters and instruments, stationery, entertainment facility and others. according to display methods, lcd panel can be divided into two types, i. e. positive and negative types. according to optical modes, lcd panel falls into four categories, namely, reflective, transmissive, transflective and holographic types
液晶顯示屏lcd分類方式有多種，如：按產品用途，可分為通信工具家用電器掌上電腦交通工具計量器械儀器儀表文教器具游藝設施等類別按顯示方式，可分為正性負性兩類按光學模式，可分為反射型透射型半透半反型全息型等4類按lcd類別，可分為tn型htn型stn型fstn型按顏色模式，可分為黃綠灰黑白藍等按觀察方向，可分為3 6 9 12點鐘及其它等。The hybrid method can simulate accurately both the imaging and polarization - dependent diffraction characteristics of a concave grating. to meet the growing need for flattened passband in a practical wdmsystem, three design methods, namely, the tapered output waveguide structure with air - slots, the three - focal - point method and the analytical method of spatial phase modulation, are introduced to achieve a passband - flattened diffraction grating device
針對實際光通信應用中對通帶帶寬的需求，本文提出了「結合空氣槽的漸變輸出波導結構方法」 、 「三焦點方法」及「顯式公式空間相位調製法」三種使平面集成型衍射光柵波分復用器件獲得平頂型頻譜響應的優化設計方法。( 3 ) study deeply the structure of fat 16 file system and the characteristic of flash disk, and develop the file management software of flash disk to manage nc files effectively according to the management idea of fat 16 file system. ( 4 ) research the module and protocol of reliable communication in serial network, which are composed of arm main control board, dsp motion control board, keyboard board, i / o control board and encoder signal collection board, and then develop communication software of the serial network. ( 5 ) study the principle of displaying char in lcd and the method of embedding font library into operating system, and research deeply the method of embedding chinese font library into os in the light of the characteristic of chinese
本論文的主要研究內容如下： （ 1 ）研究uc os -實時嵌入式操作系統在硬體平臺上的移植及其佔先式內核的任務調度原理，合理分割銑床控制系統的管理任務，根據任務的要求賦予不同的優先級和調度時間，保證任務的執行效率和實時性； （ 2 ）開發底層設備驅動程序和應用程序介面（ api ）函數，以便於進行系統應用軟體的開發； （ 3 ）深入研究fat16文件系統的結構和固態盤的硬體特性，參照fat16文件系統的管理思路，開發固態盤文件管理軟體以有效管理nc代碼文件； （ 4 ）深入研究由arm主控板、鍵盤板、 i o控制板、編碼器信號採集板等裝置組成的串口通訊網路可靠通信的模型及其通訊協議，開發串口通訊網路通信軟體； （ 5 ）研究字元的顯示原理和在操作系統中嵌入字庫的方法，在此基礎上結合漢字的特性深入研究中文字庫的嵌入方法，開發中文字庫嵌入軟體，滿足開發操作界面的信息要求； （ 6 ）深入研究三維圖形坐標變換的原理，開發實用的三維加工軌跡顯示軟體，便於操作者對零件的加工過程進行監控和診斷。You can use a visualizer to display the information in a more meaningful usually graphical fashion
。您可以使用可視化工具以更直觀的方式（通常為圖形）顯示信息。The constitutions and principles of position of gps > glonass and beidou navigation system are described all around in this article, and the following technologies are studied and realized : communication between com ports with oop technology, compound navigation with gps and glonass. calculate velocity, pseudorange difference, smoothing pseudorange with the carrier - phase and models to correct error are also done ; the transforms between wgs - 84 and pz - 90, as well as wgs - 84 and beijing54 coordinate system ; the technologies to display and manage bitmap, vector map based on mapx also ; conversion of data formats between gjb and mif data format of maplnfo corp. arithmetic of creation dem data based on contour line data from 1 -. 25000 map data with gjb format. texture the surface of terrains with corrected aviation image
本文全面介紹了gps 、 glonass 、北斗導航系統的組成、定位原理，研究並實現了面向對象的串口通信技術、 gps + glonass組合導航、測速及偽距差分、相位平滑偽距差分以及有關誤差的模型改正、 wgs ? 84和pz ? 90 、 wgs ? 84和北京54坐標系的坐標轉換、柵格地圖的顯示和管理、基於mapx的矢量地圖的顯示和管理、 1 : 25萬軍標數據和mapinfo的mif數據格式雙向轉換、基於軍標數據的dem生成演算法、基於opengl的三維地形構造、航空圖像紋理地形表面、三維坐標量算、虛擬現實模擬導航、三維地形的層次細化演算法以及數字圖像處理中的圖像增強、幾何變換、影像匹配等技術。分享友人