驗證載荷因數 的英文怎麼說

中文拼音 [yànzhèngzǎihéyīnshǔ]
驗證載荷因數 英文
proof load factor
  • 驗 : 動詞1. （察看; 查考） examine; check; test 2. （產生預期的效果） prove effective; produce the expected result
  • 證 : Ⅰ動詞（證明） prove; verify; demonstrate Ⅱ名詞1 （證據） evidence; proof; testimony; witness 2 （...
  • 載 : 載Ⅰ名詞（年） year : 一年半載 six to twelve months; six months to a year; 三年五載 three to five ...
  • 荷 : 荷名詞（蓮） lotus
  • 因 : Ⅰ動詞[書面語] （沿襲） follow; carry on Ⅱ介詞1 [書面語] （憑借; 根據） on the basis of; in accord...
  • 數 : 數副詞（屢次） frequently; repeatedly
  • 驗證 : test and verify; checking; proving; testing; confirmation; [數學] corroboration; inspection; veri...
  • 載荷 : load; loading載荷變化 load fluctuation; variation in load; 載荷裝置 load device
  1. Based on the numerical simulation and accuracy analysis to previous slab ' s test with the ansys program, the study of composite wall, with various detail design under potential load action respectively or jointly is carried on and the wall ' s atress behavior and failure mode is obtained, also the influence to wall ' s stiffness and bearing capacity by kinds of factors, including wall ' s shear span ratio, member ' s section, bar arrangement, etc. based on the hammer blow test and stiffness test, a 1 / 3 scale ten - bay model ' s modality parameter and elastic deformation characteristic is analyzed

    在對密肋復合墻板運用ansys ~ （ （ ? ） ）程序進行數值模擬、分析驗證的基礎上，對典型組合墻體在不同連接構造和不同荷載效應組合作用下的受力形態和破壞模式進行研究；計算分析了復合墻體剪跨比、邊框柱截面尺寸、邊框柱配筋大小以及墻板內肋梁肋柱配筋等諸多因素對密肋復合墻體承載力及剛度的影響，得出其變化規律。
  2. Abstract : based on laboratory test results, a model for predicting the residual deformation of soft clay under impact loading is proposed in this paper, which fits well with other test results. this model, considering several factors which affect the residual deformation such as confining pressure, impact energy and the number of impacting, can be used for the deformation prediction in the treatment of saturated soft clay by the drainage consolidation method of combining static and dynamic loading

    文摘:在試驗基礎上建議了一個預測沖擊荷載作用下飽和軟粘土殘余變形的計算模式，該模式考慮了周圍壓力、沖擊能大小、沖擊次數和沖擊遍數等幾個因素.對計算模式的驗證表明，預測值與實測值吻合較好.該模型可用於動靜結合排水固結法處理軟基時的變形計算
  3. The cross short rollers guide way and servo feed - system are the most important parts of 3mz204cnc bearing internal grinding machine made by luoyany bearing research institute. - we have analysised firstly the factor of influence with roller guide way rigid, and we have obtained a load - distortion curve. we also have analysised the dominating factors influence with distinguish ratio of guide way, and we have obtained a solution about pre - tighted load which were tested by experiments

    本文對洛陽軸承研究所研製的3mz204cnc全自動內圓磨床的核心部件：十字交叉滾子導軌和數控進給系統展開研究，首先對影響滾動導軌剛度的因素進行分析，得出載荷?變形曲線，對影響導軌解析度的各因素進行分析，得出預緊力大小與分佈對解析度和起動力的影響，並通過實驗驗證。
分享友人
分享到 Line

分享到臉書