高速射流 的英文怎麼說

中文拼音 [gāosùshèliú]
高速射流 英文
high speed jet
  • 高 : Ⅰ形容詞1 （從下向上距離大; 離地面遠） tall; high 2 （在一般標準或平均程度之上; 等級在上的） above...
  • 速 : Ⅰ形容詞（迅速; 快） fast; rapid; quick; speedy Ⅱ名詞1 （速度） speed; velocity 2 （姓氏） a surna...
  • 射 : Ⅰ動詞1 （用推力或彈力送出） shoot; fire 2 （液體受到壓力迅速擠出） discharge in a jet 3 （放出） ...
  • 流 : Ⅰ動1 （液體移動; 流動） flow 2 （移動不定） drift; move; wander 3 （流傳; 傳播） spread 4 （向壞...
  • 高速 : （高速度） high speed; high velocity （hv）; high rate; swift; fast; express; high-speed
  1. A high-speed jet is formed in the bubble due to the convolution of the fluid on the boundary of the bubble.

    由於在氣泡邊緣上流體的迴旋，在氣泡中形成了高速射流。
  2. In addition to the light it emits, the sun puts out intense stream of fast, ionized particles.

    太陽在發光的同時，還射出高速的強離子流。
  3. The high-speed streams in the solar wind seem to affect the world's weather-particularly the strength of storms in our atmosphere.

    太陽風中的高速射流似乎還影響到我們地球上的天氣，特別是影響到大氣中風暴的強度。
  4. The lateral jets are caused to incline to the direction of rotating free flow and to weaken the effect upon base flow. furthermore, the spinning effect upon lateral jet is much stronger than that upon base bleed

    與無旋轉情況對比表明，旋轉對彈丸側噴流以及底部流動均有影響，高速旋轉導致側噴射流向旋轉來流方向傾斜，並減弱其對彈底流動的引射。
  5. This paper attentatively studies the theory of traveling bubble cavitation noise emitted from high - speed underwater self - navigator of schiebe body

    本文針對回轉體形水下高速自主航行器產生的流動泡類型的空化所輻射的噪聲理論進行了探索性的研究。
  6. The button electrode is one that widely used in high energy rf accelerators, such as storage ring, and the bpm made of button electrodes has many merits like high accuracy, high resolution, resisting magnetic field, simple machinery, without magnetic core and low cost, etc. so we want to use the button electrode as the bpm in high current accelerators like the lia

    鈕扣電極束位置探測器是一種廣泛應用於射頻加速器儲存環等高能弱流加速器的一種束位置測量裝置，它具有測量精度高、解析度高、不受磁場干擾、機械結構簡單、無磁芯、造價低廉等特點。只是，至今未見有關這種束位置探測器在強流加速器（如，直線感應加速器）上應用的報導，如能將鈕扣電極束位置探測器應用於lia ，將是一件很有意義的事情。
  7. On one hand, it may exert damping on the armature of torque motor and overcome self - excitation of jet pipe. one the other hand, it may enlarge magnetic permeability of working clearances and improve magnetic circuit efficiency of torque motor to boost dynamic response speed of servo valve

    一方面可增大力矩馬達工作氣隙部分產生的阻尼，從而可以抑制射流管的自激，另一方面又可增大工作氣隙的導磁率，改善力矩馬達部分的磁路效率，從而提高伺服閥的動態響應速度。
  8. Principal conclusions were drawn as the following : the non compatibility of pressure or velocity of the gas on both sides of the contact surface is the cause of the formation of shock wave ; the heating effect of reflective shock wave to driving gas during charging or exhausting process is the internal mechanism of peak oscillating effect, and all the factors that influence the formation and the running of the shock wave will influence the peak oscillating frequency, cooling effect

    主要結論如下：熱分離機內激波形成的原因是射氣瞬間接觸面兩側壓力和速度不相容；峰值振蕩效應的內在機制為反射激波對充氣階段的驅動氣或低溫排氣的加熱，凡是影響激波形成及運動的因素都將對峰值振蕩頻率、冷效應及熱效應產生影響；當充、排氣時間比為0 . 1763時，最佳射流激勵頻率出現在高階峰值振蕩頻率上。
  9. The experiments of high speed milling of titanium alloy were conducted under different cooling and lubricating modes, i. e. dry milling, flood coolant, oil mist with nitrogen gas, cryogenic nitrogen gas jet, and cryogenic nitrogen gas jet with minimal quantities of lubricant

    在干銑削、澆注切削液、常溫氮氣油霧、低溫氮氣射流和低溫氮氣射流結合微量潤滑等冷卻潤滑條件下進行了鈦合金的高速銑削對比試驗。
  10. For high stability of the system, with the realization of hardware of the system, the second part of this paper starts from the transmission line theory, and studies the signal integrity problem of high - speed circuit system in light current. the causes of these signal integrity problems, such as signal delay, reflection, crosstalk, ground bounce noises and etc. are analyzed in theory. combined with actual design, key points of design and standard design flow of general high - speed, high - precision printed circuit board are summarized, which has been applied in actual system, and good effect has been achieved

    為使系統具有較高的穩定性，本文第二部分結合該處理器的硬體實現，從傳輸線理論出發，研究了弱電情況下高速電路印刷電路板中的信號完整性問題；從理論上分析了延遲、反射、串擾以及地彈噪聲等信號完整性問題產生的原因；結合實際設計，總結了一般高速、高精度印刷電路板的設計要點和標準設計流程，並在實際系統中獲得了應用，取得了很好的效果。
  11. ( 2 ) on the leading edge, the film cooling effectiveness at the zone immediately downstream of the cooling holes is affected by blowing ratio and mainstream reynolds number, while the effects are not important in the downstream zone far from the cooling holes. ( 3 ) on the front half of pressure surface, the effectiveness increases with decreasing blowing ratio at the downstream near the cooling row and it is contrary at the downstream far from the cooling row. ( 4 ) on the rear pare of the pressure surface, the effectiveness decreases with increasing blowing ratio and does not vary so much downstream in the cases of higher blowing ratio

    研究結果表明葉片吸力面端壁附近區域壓力系數分佈呈現出較強的三維特性，動葉吸力面尤其明顯；氣膜孔流量系數隨吹風比的增加而增大，在高吹風比情況下，流量系數逐漸趨于常數；在不同型面區域，冷卻效率分佈有較大的差異，而且吹風比與主流雷諾數的影響程度也不盡相同；低吹風比下，孔出口下游附近可以得到較好的冷卻，中、高吹風比下，冷氣射流在加速流動主流的作用下返回壁面進行二次冷卻，孔下游較遠區域可以得到較好的冷氣覆蓋。
  12. To search for high - velocity molecular emission toward massive star formation regions, and to study the connections between h2o masers, iras objects and outflow properties, we carried out a co observation for a h2o maser sample. we found that most of the objects have excess high velocity emission produced by outflows ; we find a significant correlation between co line full widths and iras luminosities. the widths are proportional to the iras luminosities

    通過在大質量恆星形成區搜尋高速分子輻射，並且研究它們與星際h _ 2o脈澤源和所聯系的紅外源之間的關系，我們發現絕大多數源都存在著氣體的高速運動並且它們是由分子外流產生的；我們同時發現在co分子的譜線全寬和所對應源的紅外光度之間存在很好的相關性，線寬隨紅外光度增加而變大。
  13. High speed cutting, water jet machining and laser machining technology are applied to kevlar fiber reinforced resin matrix composites and special kind rubber materials. valuable conclusions are obtained by experimenting investigation in chapter 8

    論文在第八章還進行了凱芙拉纖維增強聚合物基復合材料、特種橡膠材料的高壓水射流、激光和高速切削加工試驗研究，取得了有參考價值的結論。
  14. For increase the cpu efficiency more, base on the research of existing 32 - bit mips pipeline, this paper create the double - launching pipeline. by this design, one or more than one instruction completed in one period averagely, and increase the cpu efficiency remarkably

    為了進一步提高流水線的執行效率，超越流水線的極限速度，本文在對現有32位mips流水線進行研究的基礎上，創新性地提出了基於32位mips架構的雙發射流水線設計方案。
  15. A liquid drop removed from a sheet or jet may be exposed to the aerodynamic pressure effect of a high relative gas velocity.

    離開液膜或射流的液滴，可能會受到高的相對速度氣體的氣動壓力影響。
  16. Abstract : a simulated set up of high - speed simulated exhaust muzzle flow field is made up. moir ？

    文摘:在實驗室條件下，製作了模擬膛口高速射流的裝置。
  17. A comparison of the flows with different gate - opening rates shows the causes that opening the gate at a higher rate is favorable to the reduction of cavitation, gate vibration as well as the gate load fluctuation. in addition, a study has been made to show the influence of the high - speed jet flow coming downward from the narrow gate gap on the flow condition in the tunnel downstream to the gate

    通過分析比較不同閥門開啟速率對流動特性的影響，闡明了快速開啟閥門不僅有利於減少空化空蝕也有利於減小弧門振動和啟門力的脈動，此外，研究了門楣處狹窄縫隙高速射流對門后流態、壓力脈動和弧門受力等方面的影響。
  18. Material is ejected into the crushing chamber by means of high speed ejection flow formed by high - pressure air through charging ejector, and the crushing nozzles outside ejects high - speed airflow into the crushing chamber at certain direction, making the materials severely collided and fractionated, and thus crushed

    該機是靠高壓氣體通過加料噴射器所形成的高速射流，使粉碎原料被射入料碎室，粉碎室外圍的粉碎噴嘴，有方向性的向粉碎室噴射高速氣流，使物料間產生激烈的碰撞，磨擦而獲得粉碎。
  19. A new high speed and great flow solenoid valve, one of the key parts of electronically controlled fuel injection, is assembled, adjusted, which makes it in good condition, and prepares for injection test in this thesis

    電磁閥作為電控燃油系統中極為關鍵的部件，它對燃油噴射特性影響特別大。故本文對課題組自行開發、研製的高速大流量電磁閥進行了裝配、調試，使其液力狀況最佳，為噴油實驗作前期的準備工作。
  20. In this way, supersonic fluid amplifier especially bistable valve with negative pressure switch is used in the rocket projectile thanks to its advantages of switching rapidly, the ability of low temperature air to control the high temperature gas and no moving parts in high temperature gas

    超音速射流雙穩閥，特別是採用負壓切換的超音速射流雙穩閥因其具有切換快速、可用低溫氣流控制高溫燃氣和在高溫燃氣中無活動部件的優點而適用於火箭彈的姿態控制系統中。
分享友人
分享到 Line

分享到臉書