common-mode input 中文意思是什麼

common-mode input 解釋
共模輸入
  • common : adj 1 共通的，共同的，共有的。2 公眾的；公共的。3 普通的，通常的，尋常的，平常的。4 平凡的，通俗...
  • mode : n 1 法，樣，方法，方式。2 模，型；樣式，體裁，款式；習慣。3 風尚；〈the mode〉流行，時髦。4 【語...
  • input : n. 1. 【電學】【自動化】輸入；輸入端。2. 輸入電路，輸入信號，輸入功率[電壓]。3. 放入物，投入的資金。vt. ,vi. 把（數據等）輸入計算機。
  1. A complementary input stage, which consists of a p - channel pair and a n - channel pair, was used in the circuit, so that the common mode input range can extend from rail to rail. a dcls is used to shift the n - transistor curve leftward to overlap the p - transistor curve properly and keep constant transconductance in the whole common mode input range

    輸入級採用pmos差分輸入對和nmos輸入差分對並聯的結構，從而實現共模輸入范圍擴大到電源的正負兩端，並且通過兩個源級跟隨器平移nmos輸入管跨導曲線，使nmos輸入管和pmos輸入管跨導曲線的適當交疊，從而保持了這個輸入級的跨導在整個共模輸入范圍內保持恆定。
  2. An instrumentation amplifier is a closed - loop gain block that has a differential input and an output that is single - ended with respect to a reference teminal. it must amplify the differential input acurately and suppress any unwanted common - mode signals

    儀表放大器是一種能精確放大兩輸入端之間的差模信號而抑制任何共模信號，並將差分輸入轉換為單端輸出的放大器。
  3. Thirdly, the range switch circuit and filter circuit are designed in the analog input channel. to realize the safe high speed acquisition, the interface circuits are separated from the function circuits, and the isolation power with high performance and digital isolator is used to restrain the common mode disturb and noise of the input

    3 .模擬輸入通道設計有量程切換電路和濾波電路，並且採用了屏蔽、浮置技術和磁耦隔離技術，使用了高性能的隔離電源和磁電耦合器，有效地抑制了輸入信號的共模干擾和噪聲，實現了安全、高速的數據採集。
  4. The thesis has done the widespread investigation and study to the domestic and foreign ’ s technologies of analogy low voltage and low power, and analyzes the principles of work, merts and shortcomings of these technologies, based on the absorption of these technologies, it designs a 1. 5v low power rail - to - rail cmos operational amplifier. when designing input stage, in order to enable the input common mode voltage range to achieve rail - to - rail, it does not use the traditional differential input pair, but use the nmos tube and the pmos tube parallel supplementary differential input pair to the structure, and uses the proportional current mirror technology to realize the constant transconductance of input stage. in the middle gain stage design, the current mirror load does not use the traditional standard cascode structure, but uses the low voltage, wide - swing casecode structure which is suitable to work in low voltage. when designing output stage, in order to enhance the efficiency, it uses the push - pull common source stage amplifier as the output stage, the output voltage swing basically reached rail - to - rail. the thesis changes the design of the traditional normal source based on the operational amplifier, uses the differential amplifier with current mirror load to design a normal current source. the normal current source provides the stable bias current and the bias voltage to the operational amplifier, so the stability of operational amplifier is guaranteed. the thesis uses the miller compensate technology with a adjusting zero resistance to compensate the operational amplifier

    本論文對國內外的模擬低電壓低功耗技術做了廣泛的調查研究，分析了這些技術的工作原理和優缺點，在吸收這些技術成果基礎上設計了一個1 . 5v低功耗軌至軌cmos運算放大器。在設計輸入級時，為了使輸入共模電壓范圍達到軌至軌，不是採用傳統的差動輸入結構，而是採用了nmos管和pmos管並聯的互補差動輸入對結構，並採用成比例的電流鏡技術實現了輸入級跨導的恆定;在中間增益級設計中，電流鏡負載並不是採用傳統的標準共源共柵結構，而是採用了適合在低壓工作的低壓寬擺幅共源共柵結構;在輸出級設計時，為了提高效率，採用了推挽共源級放大器作為輸出級，輸出電壓擺幅基本上達到了軌至軌;本論文改變傳統基準源基於運放的設計，採用了帶電流鏡負載的差分放大器設計了一個基準電流源，給運放提供穩定的偏置電流和偏置電壓，保證了運放的穩定性;並採用了帶調零電阻的密勒補償技術對運放進行頻率補償。
  5. It has a wide input common - mode voltage range and output voltage swing, making them easy to use on single supplies as low as 2. 5 v

    該產品具有很寬的共模輸入電壓和輸出電壓擺幅，使其可使用低至2 . 5v的單電源供電。
  6. Owing to weak output signals integrated amplifier is designed, which is characteristics of shorter wires, higher input impedance, higher common mode rejection ratio and series mode rejection ratio, smaller zero shift and temperature shift

    由於輸出信號微弱，採用短線路傳輸，高輸入阻抗，共模抑制比和串模抑制比高，溫漂和零漂小的集成運放電路。
  7. While low voltage and low power is realized when designing the operational amplifier in this text, great efforts have been devoted to increasing the input common mode range and the swing of output signal, and lowing the output resistance at the same time

    只是實現低壓低功耗而不實現良好的性能顯然是錯誤的。本文在設計實現低壓低功耗的運算放大器的同時，也想法提高輸入共模範圍和輸出信號的幅度，同時降低輸出阻抗。
  8. Specifically analysed and presented the common - mode differential input stage, linear transconductance control circuit of input stage, current sum circuit, floating ab - class control output stage, the bias circuit of op amps and the bandgap reference current source circuit

    具體對運放的共模差分輸入級、輸入級線性跨導控制電路、電流和電路、浮動ab類輸出級電路、運放的偏置電路和帶隙參考電流源電路進行分析設計。
  9. The other is the design of amplifier with constant trans - conductance ( gm ) rail - to - rail input stage. when common mode input voltage changes, it provides nearly constant - gm independent of input transistor operating region ( strong, moderate or weak inversion ), and the quiet nods of the circuit for current addition and the output stage keep unchanged

    當輸入共模電壓變化時，不管它的輸入mos差分對管處于強反型區還是弱反型區，輸入級的跨度保持不變，而且輸入級後面的電流加法電路和輸出級的靜態工作點也不會隨之改變。
  10. During the process of designing the core cell, a novel continuous common - mode feedback structure has been proposed, which is suitable for the input stage

    在核心單元研發過程中，實現了極零抵消的密勒補償方案，並提出了一種適用於輸入級單元的新型連續型共模反饋電路架構。
  11. Common - mode input

    共模輸入
  12. Again, consider using amplifiers that exhibit a smooth input bias current transition throughout the applied input common - mode voltage

    再者，所用的放大器也要考慮在加到輸入端的整個共模電壓（范圍內）輸入偏置電流轉換保持平滑。
  13. For this, i adopt the new differential input stage to make input common mode range enlarged, and as far as possible not reduce its gain

    為此，採用了新的差分輸入級，使共模範圍增大，同時盡量不減少差分輸入級的增益。
分享友人
分享到 Line

分享到臉書