cooling water out 中文意思是什麼
cooling water out
解釋
冷卻水出口-
Test study on two biocides, namely quaternary ammonium salt and isothiazolinelcetone, commonly used in circulatory cooling water system has been carried out, obtaining the relationship among dosage, actuation time duration, and the killed persontage, and putting forward the principle and points needing attention for selecting the biocide
摘要對火電廠循環冷卻水系統常用的兩種殺菌劑季胺鹽及異噻唑啉酮進行了試驗研究，得出加藥量、作用時間與殺菌率的關系，並提出殺菌劑的選擇原則和注意事項。 -
The investigation of a lot of parameters about treated sandstone, brick materials and earthen materials with fluorited polymers has been carried out, such as the formation of polymer, the penetration depth, porosity, capillary absorption and penetration coefficient, water uptake, compressive strength, drilling resistance, absorption isotherms of water vapor, water vapor diffusion, color changes as well as resistance to desegregation of water, frizzing - throwing cycles, worming - cooling cycles, and so on. in addition, the influence of salt crystallization, acid and base, and uv aging have also been assessed in order to better understand the protection effects and utilization possibility of two fluorinated polymers, mainly according to astm standard and the combination of international methods together with general technological
分別以國家級文物保護單位的土質、砂巖和磚材文物樣品為對象，依據astm標準及國際通用文物保護研究方法與評估準則相結合，通過膠化物形成周期、滲透深度、孔隙度、毛細吸水和滲透系數、持水量、抗壓強度、抗鉆強度、吸附水蒸氣的能力、透氣性、外觀顏色等系列參數的測定，及凍融、冷熱循環、酸堿腐蝕后抗壓強度的衰減、可溶鹽對保護效果的影響、酸堿及光照對表面保護效果的影響，對兩種含氟聚合物及其與有機硅的共混物在文物加固保護和表面防護中的可行性和保護效果給予了系統研究。 -
The method of concentrating the decoloration solution of tylosin is usually carried out by thin film vacuum concentration. in this experiment, the concentration process is modified by using the nanofiltration membrane technique which is free from corrosive due to the extractant solvent and in the same time, heating and decomposition of the antibiotic are eliminated, the concentration course ia also distinctly shortened. in this process the small molecule can be filtered by water, and the quality of the product such as, the tyramine content, the solubility of the product, improved significantly. in addition, the membrane filtration process could save consumption of steam and cooling water
泰樂星提煉過程中原工藝脫色液用薄膜真空濃縮，本試驗改進為耐溶媒納濾膜濃縮，料液不需要加熱即可濃縮，防止了料液的高溫分解破壞，濃縮收率明顯提高在濃縮的同時，部分小分子雜質可以隨水分子一起通過納濾膜而除掉，成品質量明顯提高，解決了用原工藝成品酪胺、溶解度不合格的質量問題省去了原工藝濃縮中費用較高的蒸汽、冰鹽水，經濟效益可觀。 -
E. g water inlet, start main pump, heating, temp maintain, cooling, rinsing, chemical tank feeding, mixing, dye liquor run back, wash tank, drain out, alarm, process finish
3循環泵浦強力攪拌，能快速化鹽4自動洗桶自動 -
3. on boiler retrofit, the calculation of fuel burning, the heat calculation of boiler inside structure and convection section, and the design of structure parameter of feed water heat exchanger are made. the flue gas channels " resistance calculation and the boiler strength verifying are also carried out. replacement of water cooling wall improves heat exchanging and decreases loss of heat radiant
對鍋爐本體進行了燃料燃燒計算、爐膛結構熱力計算、對流受熱面結構熱力計算、鍋爐給水加熱器結構參數設計、煙道阻力計算及鍋爐元件強度校核等；改進了水冷壁布置使換熱效果更好，減少輻射換熱損失；改進對流段結構，更充分的利用爐膛出口煙氣余熱，提高熱效率；並且進行了煙氣阻力計算、熱效率計算和能量平衡測試，對改進后的稠油燃料和改進前進行了對比，燃燒狀況和熱效率有明顯改善。 -
The main content is : splitting tensile experiments were carried out about the standardized cube bonding specimens ( 150x 150x 150mm3 ) of the new - old concrete after high temperature. the temperature is divided into 9 groups from normal atmospheric temperature to 900, the cooling styles are natural cooling and spraying water cooling ; different interfacial treating methods : brushed with steel - wire brush, man - made chiseling ( not evenly ), man - made chiseling ( quite evenly ) ; different interfacial agents : no interfacial agent, neat cement paste, cement paste mixed with 10 % expanding agent
主要內容有：本文對75個高溫作用后的標準立方體新老混凝土粘結試件進行了劈拉試驗，溫度從常溫到900c分9個溫度段，降溫方式分自然冷卻和噴水冷卻兩種。著重考察了溫度、降溫方式、界面粗糙度及界面劑對新老混凝土粘結劈拉強度的影響規律，闡述了高溫后粘結強度下降的機理。 -
Thermodynamic analysis on wet compression process is done in this thesis and studies are done on ideal wet compression process, actual wet compression process, water droplet evaporative rate, wet compression work, inlet evaporative cooling, wet compression efficiencies and water droplet breaking. and thermodynamic model of wet compression process is established, which gives out rules of and methods to calculate wet compression parameters
本文從熱力學的角度對濕壓縮過程進行了分析，分別對理想濕壓縮過程、實際濕壓縮過程、水滴的蒸發速率、濕壓縮功、進氣蒸發冷卻、濕壓縮效率和水滴的破碎等進行了研究，建立了濕壓縮過程的熱力學模型，給出了濕壓縮過程狀態參數的變化規律和計算方法。 -
The waterpower maladjustment can make heat source out of cooling and fluid machinery out of efficiency and that the power of whole system can go up quickly. so, it is very important to balance the water power of fluid cooling system
水力不平衡會造成熱源得不到有效冷卻、流體機械運行效率不高和整個系統能耗大等不利現象，因此，對冷卻系統進行水力平衡調節非常重要。 -
Strong air - cooling condensed system can draw out oil steam and water vapor for cooling which avoid inconvenience of water cooling
強風冷凝系統，使真空抽出的油蒸汽水蒸汽快速降溫冷卻，免除了用水冷卻給用戶帶來的不便。 -
In accordance with the water tunnel that liner have cooling pipe, thermal insulation temperature rise model adopt difference expression during its through or not water phase, and optimization back analysis of parameters is carried out
針對本工程引水洞襯砌內布置有冷卻水管，對絕熱溫升模型在通水前後採用了不同的表達式，並分別對其進行了優化反演分析。 -
Considering the weakness of the solar - power adsorbers in refrigeration / air conditioning, such as the effects of heat collecting in desorption period and heat loss in adsorption period, here, a new adsorber is proposed ? ? evacuated tube which is cooled by water. simulation calculations and experiments have been performed. with a view to the intermittent characteristics of solar - powered adsorption, a continuous cycle operation for the adsorption refrigeration cooling system with active carbon fibre ( acf ) - methanol adsorption refrigeration working pair is carried out
本文針對目前太陽能固體吸附式製冷系統中吸附集熱床在解吸階段集熱效率不高和在吸附階段散熱效果不理想的狀況，以及針對太陽能固體吸附製冷系統循環的間歇性，本文提出了一種新型吸附集熱器:真空集熱管?水冷型吸附集熱器，以活性炭纖維?甲醇為工質對實現連續製冷循環方式，並對其進行了相關的性能實驗和數值模擬計算。 -
After the optimizing system is put into operation, online calculating results and operation effect is analyzed, pointing out that the base for the whole boiler soot blow optimization is the minimum loss of soot accumulation and energy consumption of soot blowing, the base for water cooling wall soot blow optimization is the combustion house outlet gas temperature difference, the base for a single heat exchange surface soot blow optimization is the degree of its soot accumulation
並對優化系統在線運行后，取得的實時計算結果和實際效果進行了分析，著重指出積灰和吹灰的經濟性最佳可作為整個鍋爐吹灰優化的決策依據，爐膛出口煙溫差可以作為爐膛吹灰優化決策的依據，受熱麵灰污程度可以作為單個對流受熱面吹灰優化決策的依據。 -
These equipments are vacuum system which is made up of diffusion pump, pipes, water - cooling baffle and rotary vane pump ; the whole chamber, wall and water - cooling wall are made of stainless steel ; the lower part is equipped with cool water sleeve which can fast take out air to gain 10 - 4 or higher vacuum, therefore they are widely used in high - tech fields, such as the platting, electronic, metallurgy, chemical engineering, atomic energy, materials and medicine etc
Kt系列擴散泵機組是由凸腔擴散泵管道水冷擋板機械泵等組成的高真空系統，整個泵腔泵壁及水冷壁全部由不銹鋼作成，下部配有降溫用急冷水套，抽氣速度快，極限真空高，它可使被抽容器獲得10 - 4或更高的高真空，因此廣泛適用於鍍膜裝飾電子冶金化工原子能材料醫藥等等各種高新技術領域。 -
Automatic control system includes the auto - temperature control, auto anti - freezing control, auto - defrost control, anti - overload protection, voltage - over range protection, diagnose, display systems. the cooling capacity varies with the changes of the environment temperature, flowing out temperature of the cooling water
電腦系統應設置自動溫度控制、自動防凍控制、自動除霜控制，熱過載、缺相、壓縮機高低壓保護，故障監測、顯示和保護等相應的控制和保護措施。 -
It specifies the process of the design, simulation and experiment of liquid cooling system. main contents of the thesis are as follows : description of the present usage of liquid cooling system, presentation of a new type of liquid cooling system and description of its work principles ; design of the liquid cooling system, which mainly deals with the design and collating calculating of serpentine condenser and heat exchangers adopted in this system. meanwhile, the model chosen calculating of compressor 、 thermal expansion valve 、 plate evaporator 、 water pump and the like equipment used in the system are also carried out
本文的主要內容如下:對液冷源使用現狀進行了描述，提出了一種新型液冷源系統並對其工作原理進行了闡述;對系統進行了設計，主要對系統中所採用的管帶式冷凝器和水側空/液換熱器進行了設計和校核計算，同時對系統中所用到的壓縮機、熱力膨脹閥、板式蒸發器、水泵等配套設備進行了選型計算;分別對製冷系統和冷卻液循環系統進行了數學建模。 -
Cooling capacity increases with the raising of the flowing out temperature, and decreases with the raising up of the air temperature. the energy consumption increases with the increasing of the temperature of the water flowing out of the evaporator, and the environment air temperature
製冷量是隨冷水出水溫度的增加而增加，並隨環境進風溫度的增加而減少，機組的功耗是隨冷水的出水溫度的增加而增加，並隨環境溫度的增加而增加。 -
In this paper, the solar and land - atmosphere radiation rates are calculated by modtran3 model and satellite observation as well as surface data, solar direct irradiance infrared irradiance solar heating rate and infrared cooling rate were calculated from 43 samples of sunshine day and 5 samples of cloudy day 3 samples of rainy day of different latitudes in 12 stations. the paper analyzed solar heating rate and infrared cooling rate in sunshine day, the factors such as zenith angle, water vapor and latitude were found out correlating with solar heating rate and infrared cooling rate. solar heating rate and infrared cooling rate change on the same day and at the same station
在對晴空大氣的計算中，本文對太陽的直接輻射與地氣系統的紅外輻射狀況進行了分析，並討論在不同的大氣狀況下太陽加熱率和紅外冷卻率的情況，找出與太陽加熱率和紅外冷卻率變化相關較大的因子?太陽天頂角和水汽條件、緯度；本文還進一步分析了不同緯度樣本的太陽加熱率與紅外冷卻率日變化及有雲、有雨情況下太陽加熱率和紅外冷卻率的變化情況：另外，文中通過改變二氧化碳在大氣中含量的方法，討論了它對太陽加熱率與紅外冷卻率的影響。 -
According to the characteristic high energy consumption of heating ventlating and air conditioning in chemical fibre plant, the paper figured out the reasons of the high energy consumption and raised the correspondent methods to decrease the energy consumption by analyzing the problems exist in the heating, refrigerating, cooling water cycling, air conditioning systems
摘要根據化纖廠暖通空調是能耗大戶的特點，從熱力系統、製冷系統、水系統、空調系統等方面進行分析，總結出耗能原因，並提出相應的節能措施。 -
Combined with the actual example in one power plant, many analyses, such as water quality analysis, ignition analysis, plasma transmitted spectrum, and scanning electron microscopy etc., have been carried out, to analyse the quality of cooling water, and properties in aspects of fouling, silt, and microorganism respectively
結合某廠實例，採用水質分析、灼燒分析、等離子體發射光譜、掃描電子顯微鏡等分析手段分別對冷卻水水質、污垢、淤泥、微生物等的特性進行了分析。 -
The appearance questions of the cooling water pipe and reasons of high fuel consumption which existed in the use process have been carried on the analysis to the reheating furnace, and the reconstruct of the cooling water system has been carried out to the reheating furnace, and has obtained the certain energy - saving effect
摘要對加熱爐內冷卻水管在使用過程中存在的問題及爐子燃耗高的原因進行了分析，並對加熱爐內冷卻水系統進行了改造，取得了一定的節能效果。
分享友人