crankshaft engine 中文意思是什麼

crankshaft engine 解釋
活塞式發動機
  • crankshaft : 【機械工程】曲軸，機軸。
  • engine : n. 1. 機械，機器。2. 引擎，蒸汽機，發動機。3. 機車，車頭。4. 工具；〈古語〉方法，手段。vt. 給…安裝發動機。
  1. Wearing of crankshaft journals and crankpin is one of the most key indexes for evaluating the working life of internal combustion engine

    摘要內燃機曲軸軸頸的磨損量是衡量內燃機壽命的一個重要指標。
  2. In the engine, oil is supplied to crankshaft and camshaft journals rotating in their supporting bearings.

    在發動機里，機油被供應到旋轉在其支承軸內的曲軸和凸輪軸軸頸上。
  3. Causes of the explosion of the crankshaft box in diesel locomotive engine and the measures taken for improvement

    2機車柴油機曲軸箱爆炸原因及其改進措施
  4. It is applied to sorts of locomotive engine, in course of revolving of crank and connecting rod mechanism, there are revolving of the crankshaft, swinging of the connecting rod and reciprocating motion, so its motion state is complex, and periodic unbalanced force, by a few components, is great

    曲柄連桿機構在高速運轉過程中，有曲軸的轉動、連桿的擺動及活塞的往復運動，其運動狀態復雜，各個部件所產生的周期性不平衡慣性力大，是引起發動機振動的主要原因。
  5. Some testing devices are of advanced ones, such as scanning electronic microscope, microfocus circular radioscope, water - immersed ultrasonic flaw detector, 3 - axis measuring machines, large - sized projector, etc. for the production of non - aero products, there are large - sized die - casting equipment, and nearly 100 pieces of specialized gear machine tools including worm - gear grinding machine, etc. it has some specialized production lines for piston, crankshaft, cylinder and housing, etc., as well as 4 flexible production lines advanced at home for motorcycle engine, and a complete set of automatic inspection test eqiuipment for motorcycle engine

    計算機輔助設計輔助加工技術正在普遍使用。在非航空產品生產方面有大型壓鑄設備殼型鑄造，包括鍋桿輪磨在內的輪專用機床100多臺，以及活塞曲軸汽缸殼體等專業化生產線。此外，還建成了具有國內領先水平的4條摩托車發動機柔性生產線，以及成套的摩托車發動機檢測設備，可進行測試數據分析，改進檢定測試方法等。
  6. This method of diesel engine fault diagnosis is feasible theoretically. while the fault diagnosis system using this method is rare, just because the crankshaft instantaneous angular acceleration measurement is demanding, such as, good frequency response, high precision

    這種柴油機故障診斷的方法在理論上是可行的，但目前這種成型的系統不多，究其原因是測量曲軸的瞬時角加速度需要系統具有良好的頻率響應特性與高精度。
  7. In this paper, the bend stress of engine crankshaft was analyzed by the finite element method ( fem ). an one - fouth crankthrow fe model is used to analyze it taking different boundary conditions into account

    本文用有限元法計算分析了發動機曲軸的彎曲應力。採用1 4曲拐有限元模型對不同邊界條件進行了研究，計算了安全系數。
  8. To adapt the circumstance in which the crankshaft torsional vibration generally exists, the new method ( tvrs method ) in which the cylinder power is inversely solved according to the torsional vibration curve is put forward and deduced in this paper, that is, the average effective pressure of each cylinder i. e. power condition of each cylinder is estimated based on a crankshaft torsional vibration curve according to the elasticity model of the actual shafting of engine and by use of the i. c. engine dynamics, the numerical calculations and the signal theory etc. although the computing workload is more, the method makes full use of the now available data of the torsional vibration of the i. c. engine, and can be used to all kinds of i. c. engine on any kind of operating condition, so it has higher application value

    為適應內燃機普遍存在曲軸扭振的情況，本文提出並推導了利用扭振信號反算的新方法（ tvrs法） ，即採用軸系中某一測點的扭轉振動信號，按軸系實際的彈性模型，依據內燃機動力學、數值計算方法和信號理論等，反算各缸的平均有效壓力，定量判斷各缸的作功狀況。此法充分利用內燃機現有的扭振資料，雖然計算工作量較大，但普遍適用於各種類型各種工況的內燃機，有較高的實用價值。
  9. Multi - flexible body dynamics is introduced into crankshaft computing, and diesel engine crankshaft dynamics simulation model is established combined with finite element method and modal superposition method

    摘要將多柔體動力學方法引入到曲軸計算中，並結合有限元法和模態疊加法建立柴油機曲軸動力學模擬模型。
  10. The key position bolt of the engine include connecting rod, crankshaft, main bearing, cylinder head, flywheel and shock absorber bolt, all of which belong to bolt fastening

    發動機關鍵工位螺栓包括連桿螺栓、曲軸螺栓、主軸承蓋螺栓、氣缸蓋螺栓、飛輪螺栓和減振器螺栓等均屬螺紋聯接。
  11. A study on the center movement of crankshaft in internal combustion engine

    內燃機曲軸軸心運動規律研究
  12. The results for two equations were analyzed and compared, which showed that the gyro effect of the crankshaft system could be ignored for low rotating - speed engine and it should be considered for higher rotating - speed engine

    結果表明，對于低轉速發動機，曲軸轉動的陀螺效應不明顯，而對于高轉速的發動機，陀螺效應不能忽略，應以考慮陀螺力矩的方程為基礎進行設計分析。
  13. Abstract : using furan sand to produce heavy diesel engine block and crankshaft eliminated defects of castings including “ penetration / burn - in ”, “ shrinkage porosity ”, “ big dimension deviation ” of cylinder block, “ penetration / bum - in ”, “ misrun ” and “ run - out ” of crankshaft, and so on

    文摘:樹脂砂鑄造工藝應用於大型球墨鑄鐵件整體鑄造柴油機缸體、曲軸生產上消除整鑄缸體「粘砂」 、 「縮松」 、 「尺寸偏差大」及曲軸「粘砂」 、 「澆不足」 、 「漏鐵液」等鑄造缺陷，具有明顯的效果。
  14. Crankshaft pully holder benz v6 engine spark plug boot puller

    奔馳引擎m112 m113鎖住曲軸皮帶輪工具
  15. In order not only in theoretics but also in practice to completely resolve the power diagnosis of each cylinder of i. c. engine according to the angular vibration curve of crankshaft, the pc instruments - crankshaft angular vibration measurement and analysis system ( tvm system ) and the electrical calibrator ( tvci system ), in which the soft and hardware resources of computer are sufficiently utilized, are developed by author

    為不但在理論而且在實踐上全面解決利用角振動信號診斷內燃機各缸作功狀況的問題，作者開發並研製了一套充分利用計算機的軟硬體資源的pc儀器? ?曲軸角振動測量分析系統（ tvm系統）和電標定器（ tvci系統） 。
  16. More often than not the combustion noise refers to the noise radiated from the cylinder cap, piston, rod, crankshaft to the engine body propelled by the pressure vibration generated out of the combustion inside the cylinder

    燃燒噪聲和機械噪聲很難嚴格區分，通常將由於氣缸內燃燒所形成的壓力振動通過缸蓋、活塞-連桿-曲軸-機體向外輻射的噪聲稱之為燃燒噪聲。
  17. The effect of uneven power and compression condition of each cylinder of diesel engine on the crankshaft instantaneous rotation ( velocity and acceleration ) curves and their interrelationship in different cylinder numbers and rotation speeds have been thoroughly analyzed by means of the crankshaft instantaneous rotation curves simulated by computer

    本文通過計算機模擬出多缸內燃機各種作功和壓縮狀況下的曲軸瞬時轉動曲線（速度和角加速度） ，詳細分析在不同缸數和不同轉速條件下，柴油機各缸作功和壓縮功不均衡對曲軸瞬時轉動曲線的影響及其內在聯系。
  18. According to the relational expression of torsional vibration of the measuring point on crankshaft and the excited moment of each cylinder of internal combustion engine ( ice ), the working condition of each cylinder was monitored and the fault of cylinder - scoring was diagnosed using the amplitude and phase characteristic of 0. 5 order torsional vibration

    摘要依據內燃機軸系測點扭振與各缸激振力矩的關系式，利用0 . 5諧次扭振的幅值與相位特性，進行內燃機各缸作功狀態監測和拉缸故障診斷。
  19. In the paper, several main steps of dynamic design, such as model set up, test modal analysis and fe modal analysis, model revising, structure dynamic response analysis, sensitivity analysis and dynamic modifying, are discussed for the military diesel main parts : crankshaft, cylinder head, engine block, and their combined structure ? ngine block & crankshaft, engine block & cylinder head, engine block & crankshaft & cylinder head, thus the paper finishes the whole tache of dynamic design and realizes the whole flow of engine dynamic design

    發動機的剛度和強度主要取決于機體、曲軸和缸蓋，為此本文對上述三個主要零部件進行了試驗模態分析和有限元模態分析，同時對組合結構?機體+曲軸、機體+缸蓋也進行了試驗模態分析和有限元模態分析並用試驗結果對有限元分析結果進行修正和驗證，以保證有限元模型的正確性和可信性。在正確、可信的有限元模型基礎上，本文進行了動力響應分析，並在假想條件下進行了靈敏度分析和動力修改，完成了動態設計的整個環節，實現了發動機動態設計的整個流程。
  20. Mainly used for crankshaft engine accessories grinding of automobile, motorcycle and ship

    主要用於汽機車船之引擎配件曲柄軸研磨專用加工。
分享友人
分享到 Line

分享到臉書