flow cast 中文意思是什麼
flow cast
解釋
流動鑄型-
Considering the electrovalence, the curve of water consumption and the reliability of water supply, this paper respectively sets up the model based on the maximal flux and the model based on the expectation flux. it takes yearly expenditure converting value and yearly cistern converting value as target function and takes continuity equation, velocity of flow and compression resistance of cast iron pipeline as restrictions and sets up the pga model on optimal design of water supply networks
考慮到峰谷電價、用水量變化曲線及用水可靠性因素的影響，分別建立了以最高時流量設計管網的模型和以期望時流量設計管網的模型，以年費用折算值加上清水池年造價折算值為目標函數，以連續性方程、管中流速和鑄鐵管耐壓值等為約束條件，進行并行遺傳演算法對給水管網優化設計的實現。 -
Considering of the problems exist in practice, large orifice discharge principle is employed to study the pressure distribution of ring runner system, the even ab lity for discharging of gates, the relationship of flow with the position of spr ue and the type of gates. a new design idea about circular runner system of cast is proposed
根據生產中存在的問題，用大孔出流理論研究了環形橫澆道系統的壓力分佈、內澆道出流均勻性及流量與直澆道引入位置和內澆道引入方式之間的關系，提出了圓形鑄件環形橫澆道系統新的設計思想。 -
The electric power harmonic comprehensive control system with low cast and high security is applied in this article. it adopts that sourced compensation links with non - sourced compensation herewhich the former is realized by high frequency pwm control technology and the latter is carried out by crystal switch formed by non - flow and over - voltage. it can realize stepless modulation with imaginary power, mightiness compensation of harmonic and negative electricity, and circuitry consumption debasing are achieved
提出採用有源補償與無源補償相結合的電力諧波綜合治理技術及裝置，無源部分採用無涌流和過電壓的晶閘管控制電容器技術實現，有源部分採用高頻pwm控制技術實現，成本低、可靠性高、可實現無功功率的無級調節、強力補償諧波電流和負序電流，降低線路損耗。 -
And the microstructure, the hardness and the wear resistance properties of complicated parts had also been studied and analyzed. the results showed that under the same experiment condition, the semi - solid flow and deformation properties of the composites increased with the increasing of the sic particles " volume fraction which below 12 %, that he composite reinforced with different volume fraction of sic particles were die - cast into complicated parts successfully, that sic particles dispersed even more uniformly in their complicated parts, and that he complicated parts " hardness was better than the composites "
結果表明，在sic顆粒體積含量低於12的情況下， sic顆粒含量越高，復合材料的成型性能越好； sic顆粒增強鋁基復合材料能夠用壓鑄的方法制備復雜壓鑄件； sic顆粒在壓鑄件中分佈更為均勻，且呈單顆粒；壓鑄件的硬度比復合材料鑄錠的硬度高； sic顆粒增強鋁基復合材料的壓鑄件耐磨性高於復合材料鑄錠。 -
Precision casting : fittings for oil pump and flow rupple, fittings for motorcydes and bus, stainless cast steel parts ductile iron pacts ; grey castiron parts : fittings for air conditioner compressor and motorcydes ; macbine manufacturing : litting for oil pump and flow nipple
公司主要生產各種牌號的球鐵、不銹鋼、合金鋼鑄件，目前主要品種為管道配件類，不斷水專用器材類，閥門及配件類，建築機械零件類、工業用鼓風機類、鑄造機械設備以及機加工總成。
分享友人