forward pressure 中文意思是什麼
forward pressure
解釋
送進壓力-
First this paper describes the composing and technics of drillers ; then the composing of control system based on s7 - 300plc is described ; then thinking of such characteristics of oil driller as complexity and long delay, this paper brings forward the control strategy of combining the fuzzy control with smith estimate control algorithm, and sets down the way of auto - driller based on discal hydraulic pressure brake. at last the experiment based on matlab by computer shows that the effect of this control mode is very good and all performance are famous
首先本文闡述了鉆機的組成與工藝特點，然後描述了基於西門子s7 - 300plc的控制系統組成，然後針對傳統鉆機自動送鉆控制策略落後的缺陷，同時考慮到鉆機的復雜性、大滯后等特點，提出了模糊控制演算法與施密斯（ smith ）預估控制演算法相結合的控制策略，給出了基於液壓盤式剎車的自動送鉆智能控制策略， matlab的模擬實驗證明該控制方式控制效果良好，各方面性能指標都達到理想要求。 -
Abstract : making a comparison between bladder - type accumulator and piston accumulator, the paper presents the characteristics of both devices, puts forward and recommends to “ piston accumalator with gas bomb ” circuit design solution for large oil compensating and pressure maintaining system and makes an exposition of the operating process and methods for pressurizing by air inflation with piston accumulator
文摘:對比說明了囊式和活塞式蓄能器的特點，對大型補油保壓系統提出了推薦採用「帶儲氣瓶的活塞式蓄能器」迴路設計方案的觀點，並闡述了利用活塞式蓄能器進行充氣加壓的操作過程和方法。 -
By analyzing and experimentally verifying the model, new ways of improving mixer performance were put forward. ( 1 ) heat water should be used in the mixer ' s temperature control to make the mixer work with optimal parameters. ( 2 ) the surface materials of the mixing chamber and rotors should be chosen rationally to change material surface energy and increase friction on them. ( 3 ) when the compound was processed under higher pressure of floating weight, shallow groovers or stripes parallel to the axle of the rotor should be made on the mixing chamber internal wall to increase the real contact area and improve mixing effect
通過對模型的分析和實驗驗證，提出了提高密煉機混煉效果的新途徑： （ 1 ）密煉機溫度控制採用溫水冷卻，使密煉機處于最佳工作狀態； （ 2 ）通過合理選擇密煉室和轉子表面材料以改變材料表面能來增大膠料與它們之間的摩擦力； （ 3 ）在上頂栓壓力較大的條件下，在密煉室內壁與轉子軸線同方向加工淺的光滑槽可明顯改善混煉效果。 -
Although the demand for detecting performance of a sealed - cabin was put forward in 1980s, as the advance of products, today not only airproof but also sealed - cabin drying process and hygrothermograph and pressure detection online are required. the more advance of our product, the higher means of detection are required
從80年代初僅僅提出的密封艙氣密性能檢測的要求，到今天的氣密性能、密封艙乾燥處理及密封艙溫濕度和壓力在線檢測的要求，產品的性能越來越先進，對檢測的手段也提出了更高的要求。 -
First, it was taken that a discuss about the effects of geometry parameters of each piezocrystal on direction parameters ( main lobe width, side lobe amplitude, elimination of grating lobes ), amplitude of ultrasonic pressure, element viberation pattern, mutual radiation among elements, efficient test regions, ability to keep accurate and near - field distance and so on. based on the direction of ultrasonic field in ulpa deduced by ourselves. in addition, on the base of integrating all kinds of factors, it was put forward that the principle and method for optimized design of geometry parameters of piezocrystals in ulpa transducer, and its design programme and interface were compiled
首先在推導超聲相控線陣換能器聲場的指向性的基礎上，就各個晶片幾何參數對指向性指標（主瓣寬度、旁瓣幅度、消除柵瓣） 、聲壓幅值、陣元振動模式、陣元間互輻射、有效檢測區域、精確控制能力、近場長度等方面的影響進行了論述，並在綜合各方面影響的基礎上，提出了晶片幾何參數優化設計的原則和方法，編寫了設計程序和界面。 -
For the requirement of abpm ' s low power dissipation, pocket size and 24h ambulatory mornitoring, the paper first put forward and accomplished a new method : charging self - adaption blood pressure measurement method ( csbpm ). it is the key technology on abpm
針對abpm微型化、低功耗、 24h動態監測的要求，我們在大量理論研究和臨床實驗的基礎上，首次提出並實現了基於充氣的自適應無創血壓測量技術，它是abpm的關鍵技術。 -
This thesis used aerodynamics equation and mechanics of materials knowledge analyzed the high pressure caused by overloading in terms of theory. by compared the increment of pressure in a not full container with the full one and combined with the igc - code, this thesis put forward a method of calculating safe loading capacity under different temperature
本文應用了氣體力學方程和材料力學理論知識，對充裝過量導致過高的液貨艙壓力進行了理論分析，對比保留有氣枕時的液貨艙的壓力增量和充裝過量時造成滿液的壓力增量，並結合igc規則對充裝極限的規定，提出了不同溫度下的安全貨液充裝量的計算方法。 -
Grains moving in saltation receive most of their forward momentum directly from the pressure of the wind.
在跳躍運動中的顆粒直接接受來自風壓力的大部分向前的動量。 -
Finite volume method is appilied in numerical modeling of the flow in no - pressure tunnel of high water reservoir in this paper. i select standard k - turbulence modeling that put forward by launder and spalding in 1972 by weighted poly - turbulence modeling. the difficulty is that there is free surface in flow, but free surface problem ' s calculating region is indefinitely
本文利用有限體積法對高水頭下水庫無壓泄水洞水流進行了紊流數值模擬，根據多種紊流模型的優缺點進行比較，選擇了launder和spalding於1972年提出的標準的k ?紊流模型。 -
The pressing of bottom, side attaching and forward - and - backward squeezer can be finished at one time, and also can be finished separately with high pressure and fastness
壓底、壓邊及前後束緊，可一次完成，亦可選擇單個動作完成，具有壓力大，壓合牢固之特點。 -
One robust compensation adjustment is presented, based on which and h ? mixed sensitivity control method, then a new h - control method is brought forward and is applied in the pressure - adjusting loop of this system. h mixed sensitivity control method is applied in the position - adjusting loop. system simulation and experiments prove that using these two control methods, performance of close - loop system is very good and excellent robustness is obtained too
在此基礎上，針對h _控制混合靈敏度優化策略的特點，提出了一種新的h _控制方法，並將其應用到卷取機步進控制系統的壓力控制環節，同時首次將h _控制混合靈敏度優化策略應用於卷取機步進控制系統的位置控制環節，系統模擬和物理系統模擬實驗證實這兩種控制方法不僅保證了閉環系統特性，還具有良好的魯棒性。 -
To adapt the circumstance in which the crankshaft torsional vibration generally exists, the new method ( tvrs method ) in which the cylinder power is inversely solved according to the torsional vibration curve is put forward and deduced in this paper, that is, the average effective pressure of each cylinder i. e. power condition of each cylinder is estimated based on a crankshaft torsional vibration curve according to the elasticity model of the actual shafting of engine and by use of the i. c. engine dynamics, the numerical calculations and the signal theory etc. although the computing workload is more, the method makes full use of the now available data of the torsional vibration of the i. c. engine, and can be used to all kinds of i. c. engine on any kind of operating condition, so it has higher application value
為適應內燃機普遍存在曲軸扭振的情況，本文提出並推導了利用扭振信號反算的新方法（ tvrs法） ，即採用軸系中某一測點的扭轉振動信號，按軸系實際的彈性模型，依據內燃機動力學、數值計算方法和信號理論等，反算各缸的平均有效壓力，定量判斷各缸的作功狀況。此法充分利用內燃機現有的扭振資料，雖然計算工作量較大，但普遍適用於各種類型各種工況的內燃機，有較高的實用價值。 -
Some fuzzy concepts exist in resolving forward extrusion solid object ' s unit extrusion pressure with slip line technique in current documents
摘要現有文獻用滑移線法求解正擠壓實心件的單位擠壓力，存在一些模糊概念。 -
The main tests and researches are as following : to study the ac flashover characteristic of composite insulator in different icing states by imitating tests in multifunctional artificial climate chamber, and analyze the effect of ice amount and icing water conductivity on flashover voltage, put forward a flashover mechanism by analyzing the icing flashover process. to study the ac flashover characteristic of composite insulator in different altitude and icing states together by imitating tests in multifunctional artificial climate chamber, and mainly analyze the effect of altitude ( air pressure ) and ice amount on flashover voltage, and investigate the flashover mechanism. to investigate the effect of high altitude and icing on the hydrophobicity of composite insulators
本文主要進行了以下試驗研究： 1 ）在多功能人工氣候室里模擬不同覆冰程度下合成絕緣子的交流閃絡特性，主要分析覆冰量和覆冰水電導率對閃絡電壓的影響，並對其覆冰閃絡過程進行機理分析； 2 ）在多功能人工氣候室里模擬不同海拔高度和覆冰程度綜合作用下合成絕緣子的交流閃絡特性，主要分析海拔高度（即氣壓）和覆冰量對閃絡電壓的影響，並進行閃絡機理分析； 3 ）研究高海拔和覆冰對合成絕緣子憎水性的影響。 -
The thesis analyzed the present transferring status between pudong airport and shanghai " s incity. through forecasting the long - dated flux of pudong airport and the area near it and combining the planning scheme of shanghai urban rapid mass transit, the thesis learned the helpful experience of the traffic organization in typical airport abroad and used the scientific analyzing model of public traffic flux forecasting to put forward some reasonable suggestion of the bottleneck question between pudong airport and incity : the one is to use the present no. 2 subway as the future airtrain to take on the most part of the flux and meantime present the concept of feeder efficiency to quantitative analyze the choice of feeder station ; the other is to set up cat ( city air terminal ) to convenient the passenger to come airport rapidly and economically in order to lessen the pressure of the traffic and improve the whole service quantity of civil aviation transportation
本文分析了浦東機場與市內目前的換乘現狀，從預測浦東機場及緊鄰空港區域中遠期的客流量入手，結合上海市政府快速軌道交通的規劃方案，並且學習境外典型機場交通組織的有益經驗，利用規劃中的公交客流預測等科學分析模型，對浦東機場與市中心的軌道交通銜接提出了合理的建議：一是利用目前的地鐵二號線作為航空軌道共享線來承擔大部分進出空港的客流，並且給出了以接運效率最大化為目標函數的接運公交軌道站點比選模型；二是在市中心設立城市航站樓以方便旅客快速、經濟地到達機場，從而減少道路交通壓力，提高航空運輸的整體服務質量。 -
Man b & w 10l90mc diesel engine is a new type of man diesel company and it has been used in large container vessel. in order to investigate into the characteristic of shaft torsional vibration when any single cylinder flames out and how that affects the main power propulsion system of a ship, the author puts forward a new way of calculation concerning the shaft torsional vibration when the mean indicated pressure of other cylinders remain unchanged
在此基礎上，開發了新的船舶軸系扭轉計算軟體，並以manb & w公司近幾年新推出的一種大功率多缸柴油機manb & w10l90mc型柴油機為例，分別進行了額定功率下和單缸熄火下的扭轉計算，並提出單缸熄火時其他缸平均指示壓力保持不變的軸系扭振計算方法。 -
A new calculation method for optimizing diesel engine performance, called nonlinear regression - mess method, is put forward. in this paper, 25 groups of simulated values are calculated from the diesel engine working model, specific fuel consumption, peak pressure, rate of pressure rise, nox and peak temperature are fitted into explicit function about compression ratio and fuel injection advance angle
本文利用柴油機工作過程模型，得出25組模擬計算數據，利用非線性回歸將油耗、最大爆發壓力、壓力升高率、 no _ x濃度及最高燃燒溫度擬合成壓縮比和噴油提前角的顯函數，並用網格法進行優化，用c語言編制了優化計算程序，得出最佳的壓縮比和噴油提前角，使其優化匹配。 -
The improving problem of hydraulic pressure change direction system of loading machine was disscussed. the ten tative ideas of utilizing limited pressure change direction system were put forward
探討了裝載機液壓轉向系統的改進問題，提出了採用限壓式液壓轉向系統的設想。 -
Based on the analysis of current control programs of the connecting and dismounting rods ? coupling for the down - the - hole, the automatic control program is put forward for the propulsion floated by rotation pressure controlling, and the program is tested
分析了新型液壓碎石機液壓系統的特點及要求，研究設計了新型的液壓控制系統，並介紹了其組成與工作原理，以及流量和壓力的調節與控制原理.該新型液壓控制系統可在操縱臺上直接控制碎石沖擊器的工作參數和性能參數，系統效率高，操縱控制舒適方便，能適應不同工況的需要 -
Due to the low mechanical efficiency and long circulating period of the down - charging system of cold bed in bar production line, this paper puts forward the improving project, which adopts ethernet supplemented by dp network, applies the fm350 - 2 advanced counter and suitable maths model and combines the technique of the transducer and hydraulic pressure drive control to realize auto - control
摘要針對棒材生產線上冷床下卸鋼系統機械效率低、運行周期長，不能適應快節奏生產的現狀，採用以工業以太網為主、 dp網為輔的網路通訊，應用西門子fm350 - 2高速計數器，通過有效的數學計算模型，結合變頻器和液壓傳動控制技術，實現網路自動化控制。
分享友人