laminated composite structure 中文意思是什麼

laminated composite structure 解釋
層疊式組合結構
  • laminated : adj. 由薄片疊成的；層狀的。
  • composite : adj 1 併合的，復合的，混成的，合成的，集成的。2 【建築】混合式的；【造船】鐵骨木殼的。3 【植物；...
  • structure : n. 1. 構造，結構；組織；石理，石紋。2. 建造物。3. 【化學】化學結構。4. 【心理學】（直接經驗中顯現的）結構性，整體性；整體結構。adj. -d ,-less adj.
  1. Wavelet analysis in damage detection for laminated composite structure

    小波分析在復合材料層合結構損傷檢測中的應用
  2. Then discuss the stress concentration problem of the honeycomb structure to use the model of “ laminated composite structure with circular hole. then discuss the thermal control technique of the mfs, and built the model of heat transfer

    考慮到在蜂窩結構板上開設埋孔會引起應力集中的現象，所以還進行了對復合材料板應力集中問題的理論分析，得出了「帶圓孔的復合材料層板」應力集中系數的表達式。
  3. 2. a relevant formula of eight - node adhesive finite element is deduced in the paper, which is based on a separately interpolation scheme for reissner - mindlin plate element. a load capability analysis method for patched composite laminated structure is established by using tsai - hill failure criterion and thai ' s reduced stiffness scheme, and corresponding computer code is also developed

    在任意四邊形四節點復合材料層合板殼單元的基礎上，推導了相應的八節點膠單元，並採用蔡-希爾強度理論以及蔡氏剛度退化準則，對復合材料層合板膠接補強結構進行剛度分析和極限承載能力分析，編制了相應的有限元分析程序。
  4. The piezoelectric laminated shell is a kind of adaptive structures, and integrated with composite base structure, piezoelectric sensor / actuator and controller units, which can observe the external disturbances by sensor, then change the structural state to adapt for the environment ' s change by the actuator, through regulation of controller units

    壓電層合殼是一種由復合材料基體、壓電作動傳感元件和控制單元所組成的自適應結構。它利用傳感元件感受外界環境作用下的響應信息，在控制單元單元的調節下，通過驅動作動元件去改變結構狀態，以適應環境條件的變化。
  5. Based on the background of active control of advanced composite barrel ' s vibration, this dissertation focuses on the structure dynamic modeling technique of the piezoelectric laminated shell and satisfactory control of its vibration

    本文以先進復合材料身管的主動減振為背景，主要研究壓電層合殼的結構動力學建模技術及其振動的滿意控制。
  6. Experimental specimens embedded with superelastic wires, which are rectangle laminated composite panels with a circular hole and square plate, were prepared to make respectively tensile and bending test. the outputs of sensors embedded in structures were timely acquired to monitor mechanical properties of structure

    對含孔洞的典型構件進行拉伸試驗，對方板構件進行彎曲模擬受載試驗，實時採集結構中傳感元件的輸出，以實驗的方法監測結構宏觀力學行為。
分享友人
分享到 Line

分享到臉書