oil suction 中文意思是什麼

oil suction 解釋
吸油口
  • oil : n 1 油；油類；油狀物〈一般是不可數名詞，表示種類時則用 pl 如：vegetable and animal oils 植物油和...
  • suction : n. 1. 吸，吸引，吸入；吸力。2. 吸氣，吸氣通風；【物理學】空吸。3. 〈英國〉喝酒。4. 吸水管。
  1. Analysis of kinematical and kinetic characteristics on double donkey headed oil suction pump

    雙驢頭抽油機的運動與動力特性分析
  2. Discussion on the factors affecting oil suction pump vacuum of model wby210 stabilized soil mixer

    210型穩定土拌和機吸油泵真空度大小的因素
  3. By arrangement of the control channels through which the hydraulic fluid flows from the discharge chamber into the oil reservoir, this allows any gas bubbles being released from the hydraulic fluid during the suction stroke to be expelled into the oil reservoir

    通過液壓油經控制通道由排出腔流入油槽的這種布置，使得任何在吸入沖程從液壓油中釋放出來的氣泡都被排到油槽中。
  4. When the new ipr is used to direct the design of suction parameters of rod pumping wells, the oil wells can run at the reasonably flowing pressure and the maximal liquid output, which is of important significance to raising economic effects of low permeability oil field

    應用新型油井流入特性曲線指導油井抽汲參數設計，確保油井在合理流壓下生產，可以實現油井產量最大化，提高低滲透油田開發的經濟效益。
  5. The model of variability of submergence depth is established based on the law of volume balance, and the changing trends of parameters like submergence depth etc are analyzed. according to the principle of supply and discharge balance, the method to predict oil yield is presented. subject to different objective functions, the corresponding optimum combinations of suction parameters are analyzed, and the importance of choosing objective function to optimum combination of suction parameters is emphasized

    本文研究了油井流入動態關系，根據井筒內液量平衡原理，建立了沉沒度變化的數學模型，分析了沉沒度等參數變化規律；根據油井供、排平衡原則，得出了抽油泵排量系數相對穩定狀態下產量預測的關系；分析了不同目標函數下，油井抽汲參數的組合效果，指出了目標函數選取對參數合理組合的重要性。
  6. Using method of oil - flow visualization techniques and measuring pressure distribution along airfoil chordwise and spanwise studies have been down for sidewall boundary - layer displacement effect in two - dimensional wind tunnel. three different chord models were tested in two different wind tunnel. in order to clarify the sidewall effects and study method of sidewall suction theory and sidewall interference correction method to remove effects of sidewall on model. the results of oil - flow test show that selection rational suction wary can obtain better testing results. by investigations on effects of the sidewall boundary layer suction and application of a sidewall interference correction method

    為了很好地解決多機場航班隊列的擁塞問題，在將進場容量、離場容量與機場容量作為統一整體的情況下，充分考慮了機場間的網路效應，詳細研究了多機場航班隊列的優化問題，建立了多機場開放式非實時流量管理的數學模型，通過選取適當的決策變量，使其為線性0 - 1整數規劃模型，實現了中心流量集中管理.與其它演算法不同，本文提出的啟發式隱枚舉演算法能很好地解決此類問題，對某機場網路系統的模擬結果證明了所建模型、優化演算法及相應軟體的有效性和可靠性
  7. The equipped air valve design, can remove air with slight amount of vapors by suction as well as protect the cooling vapor from mixing into oil, so as to prolong the lifetime of oils in the pump

    裝有氣鎮閥，在抽除含有少量水蒸汽的空氣時，打開氣鎮閥可避免水蒸汽凝聚后水混入油中，延長泵油的使用壽命。
  8. Rubber hose assemblies for oil suction and discharge services - recommendations for storage, testing and use

    抽油和排油用橡膠軟管組件.貯存試驗和使用建議
  9. Methods of test for rubber and plastics hoses and hose assemblies - hydraulic pressure tests - hydrostatic tests for oil suction and discharge hose

    橡膠和塑料軟管組件的試驗方法.第102部分:液壓試驗.第10節:吸油和放油軟管靜液壓試驗
  10. On the basis of 3d modeling and virtual prototyping technology and energy saving transformation method for parameterized simulation moving beam typed oil suction pump, and using the eccentric gear reducer to replace the ordinary gear reducer to let the driving radius of eccentric gear be kept a variation of similar tendency with the load of crank in order to improve load property of the motor, thus raised the working efficiency of the entire oil suction pump and achieved the effect of energy saving

    摘要基於三維建模和虛擬樣機技術，參數化模擬游梁式抽油機節能改造方法，用偏心齒輪減速器代替普通齒輪減速器，使偏心齒輪驅動半徑和曲柄負載保持同趨勢變化，以改善電機負載特性，提高整個抽油機的工作效率，達到了節能的效果。
  11. Rubber hose, oil suction and discharge, offshore mooring

    近海停泊排吸油橡膠軟管
  12. Diameter of the suction and evaporating pipes should be decided by oil circulation and reconfirmation of gas speed

    吸氣管及蒸發器管徑，應考慮回油並再次確認流速后確定。
  13. The suction helps to pull the oil off of the liquid level

    這個吸力有助於將液位上的油拉出來。
  14. Rubber hose assemblies for oil suction and discharge services - specification for the assemblies

    油吸放裝置用橡膠軟管組件.組件規范
  15. Ships ' oil suction bellmouths

    船用吸油喇叭口
  16. Rubber hose - on shore oil suction and discharge

    岸上排吸油橡膠軟管
  17. Rubber hoses and hose assemblies - on - shore oil suction and discharge - specification

    海岸吸油和卸油用的橡膠軟管和軟管組件.規范
  18. Rubber hose assemblies for oil suction and discharge services - specification for the assemblies ; german version en 1765 : 2004

    油的吸放設備用橡膠軟管組件.組件規范
分享友人
分享到 Line

分享到臉書