shear plane method 中文意思是什麼

shear plane method 解釋
剪切面法
  • shear : vt vi （sheared 〈古語〉 shore; shorn sheared）1 剪（羊毛等）；修剪（樹木）；剪（呢絨的）長毛。2 ...
  • plane : n 懸鈴木屬樹木。n 1 平面，水平面，面。2 （知識等的）發達程度，水平，階段。3 【航空】機翼面；〈常 ...
  • method : n 1 方法，方式；順序。2 （思想、言談上的）條理，規律，秩序。3 【生物學】分類法。4 〈M 〉【戲劇】...
  1. Test method for in plane shear

    拉擠玻璃纖維增強塑料桿面內剪切強度試驗方法
  2. Firstly, the shear and normal stresses of tapered members under the transverse load or axial load are analysed, and the stresses formulas are obtained which are different from those of the prismatic ones. secondly, research is done on the in - plane inelastic stability of tapered members under axial loads about strong axis and weak axis. a new design method is suggested in which the tapered member is equivalent to the prismatic member with the cross - section at the larger end of the tapered member

    同時由分析可知，目前採用的將變截面壓桿按照彈性極限荷載等效的原則等效成以小端截面為準的等截面壓桿的設計方法，在彈塑性階段低估了壓桿的承載力，即彈性等效的壓桿在彈塑性階段並不等效，實際變截面壓桿的承載力比等效的等截面壓桿的承載力要高。
  3. Based on the continuous damage theory, considering the shear effect, the high - order shearing, flexural and in - plane deformation coupling model is built ; through the nonlinear fem analysis of rc beams strengthened with frp, the damage theory and damage course is researched ; compared with experiment results, it shows that the model is effective ; the fem analysis software is prepared to provide simple and effective method for the engineering application ; using the soft the frp strengthened beams before and after damage is modeled so as to provide the theory base for engineering application

    摘要基於連續損傷理論，考慮膠層的剪切效應，建立frp加固鋼筋混凝土梁的高階剪切彎曲及面內變形耦合模型，編制了有限元分析的軟體，進行非線性有限元分析；通過與已有的試驗結果進行對比，證明該模型的簡單，有效性；利用該軟體對未加固混凝土梁，初始進行加固的混凝土梁以及最大拉應變達到極限值時進行加固的混凝土梁等幾種情況進行數值模擬。
  4. Test method for in plane shear strength of pultruded glass fiber reinforced plastic rods

    拉擠玻璃纖維增強塑料桿面內剪切強度試驗方法
  5. By virtue of the design features of the mania dam, this paper studies the dynamic characteristics of the dam materials. by comparison with other similar projects, it presents a curve for dynamic characteristics of clay core materials and rockfill materials, makes analysis on the dam ' s plane dynamic response by finite element method, calculates the dam ' s seismic acceleration, the dynamic shear stress of the rockfill, and the dynamic stress of the cutoff wall in the overburden layer

    本文針對滿拉土心墻堆石壩的設計特點，進行了築壩材料動力特性試驗研究，通過與相關工程對比給出了心墻料和堆石料的動力特性曲線，採用有限元方法進行了大壩平面動力反應分析，計算了大壩的地震加速度、堆石體動剪應力及覆蓋層防滲墻的動應力。
  6. This paper relates to some problems about the determination of design ground motion parameters, which include the choice of the attenuation relationship of rock horizontal acceleration response spectrum, the impact of focal depth to rock peak horizontal acceleration and rock response spectrum curves, the choice of intensity envelops function and random input phase, the choice of soil nonlinearity and shear wave velocity, scale of design ground motion response spectrum etc. in the researches of relative aspect, based on a typical section plane of the engineering site, influence of the change of some parameters on design ground motion parameters and the existing errors and corresponding rules are studied by using the method of one dimension model of equivalent linearization

    摘要研究了確定設計地震動參數中涉及的若干問題，其中包括基巖水平加速度反應譜衰減關系的選擇、震源深度對基巖水平加速度峰值及基巖反應譜曲線的影響、強度包絡線函數及輸入隨機相位的選擇、土體非線性特性參數和土層剪切波速值的選擇、設計地震動反應譜的標定等問題。
  7. Reinforced plastics - determination of the in - plane shear modulus by the plate twist method

    增強式塑料製品.採用板扭法對面內剪切模量的測定
  8. Testing methods for in - plane shear properties of carbon fiber reinforced plastics by plus and minus 45 degrees tension method and two pairs of rails method

    用加減45度拉伸法和兩對軌法測定碳纖維增強塑料的平面剪切性能的試驗方法
  9. Standard test method for in - plane shear properties of polymer matrix composite materials by the rail shear method

    軌道剪切法測定聚合母體組合材料平面剪切特性的標準試驗方法
  10. Finite difference method analysis on the shear in plane of glass plate with overlapped connector under the body force

    夾板約束邊界玻璃板體力作用下面內受剪的有限差分解
  11. Shear plane method

    剪切面法
  12. Standard test method for in - plane shear strength of pultruded glass - reinforced plastic rod

    擠拉制玻璃纖維增強塑料棒平面剪切強度的標準測試方法
  13. Fibre - reinforced plastic composites - determination of the in - plane shear modulus by the plate twist method

    纖維增強塑料復合材料.用板捻法測定平面內剪切模量
  14. Fibre - reinforced plastic composites - determination of the in - plane shear modulus by the plate twist method iso 15310 : 1999 ; german version en iso 15310 : 2005

    纖維增強塑料復合材料.用板捻法測定內剪模量
分享友人
分享到 Line

分享到臉書