surface blow 中文意思是什麼
surface blow
解釋
上排污-
The quality of furan sand castings is usually better than clay sand castings, however, some defects are also very easy take place with furan sand castings such as blow hole, metal penetration, veining, cracking, slag inclusion, hardness too low, surface recarburation, surface sulphuration, nodularity degeneration etc, which were usually caused by improper raw materials selection, improper method design, incorrect moulding or / and core - making
摘要呋喃樹脂砂鑄件質量一般比黏土砂鑄件好，但如果原材料選擇、工藝設計、造型和制芯操作不當，也會產生氣孔、粘砂、脈紋、裂紋，夾渣、硬度不足、滲碳、滲硫和球化不良等鑄造缺陷。 -
Coating machine ( whether two - sided gyro wheel scribble, is it scribble two, flatten to blow the form and two, two hot to dissolve and react the trough the polishing form ) surface processing and manufacturing is antibiotic, defends, waterproof, ventilative to used in not weaving cotton cloth, pack and prevent germs to infect and isolate and use the cloth in food, medical treatment
塗布機（雙面滾輪塗、單面刮塗二次、壓平及拋光單面二次、兩座熱溶反應槽）用於不織布表面加工製造抗菌、防? 、防水、透氣，食品、醫療包裝和預防病菌傳染隔離用布。 -
The reason and prevention of four kinds defects including surface wrinkled skin ( carbon built - up ), chock, blow hole, deformation, was introduced in this part of the article
本部分主要介紹表面皺皮（積碳） 、嗆火、氣孔、尺寸超差及變形等缺陷的產生原因和防止方法。 -
Zhejiang 8 amounting to tunnel engineering limited company is alley of well of bridge of road surface of channel of pilot a ship into a harbour of water and electricity of volume road tunnel, railroad channel, irrigation works, roadbed, mine, large cubic metro of earth and stone blow up the professional construction company that construction is an organic whole, have channel highway project to always contract two class aptitude
浙江八達隧道工程有限公司是集公路隧道、鐵路隧道、水利水電引水隧道、路基路面橋梁、礦山井巷、大型土石方爆破施工為一體的專業施工企業，擁有隧道公路工程總承包貳級資質。 -
The snow is crusted, the light seeds can blow a few hundred feet on the surface.
假如有些時候雪的表面形成了硬殼，輕的種子能夠被風吹走幾百英尺遠。 -
After the optimizing system is put into operation, online calculating results and operation effect is analyzed, pointing out that the base for the whole boiler soot blow optimization is the minimum loss of soot accumulation and energy consumption of soot blowing, the base for water cooling wall soot blow optimization is the combustion house outlet gas temperature difference, the base for a single heat exchange surface soot blow optimization is the degree of its soot accumulation
並對優化系統在線運行后，取得的實時計算結果和實際效果進行了分析，著重指出積灰和吹灰的經濟性最佳可作為整個鍋爐吹灰優化的決策依據，爐膛出口煙溫差可以作為爐膛吹灰優化決策的依據，受熱麵灰污程度可以作為單個對流受熱面吹灰優化決策的依據。 -
Finally, in section three, rayleigh wave exploration method is used in a practical project - northern stone material trade market. the embedded depth of cobble substratum of the whole site, and the regression equation between the test blow count ( n63 ) standard penetration and the surface wave velocity ( vr ) are obtained in the process. a good case study is provided for the practice of the subjected method in this section
第三部分是將瑞雷波法勘探應用於北方石材交易市場的工程實際中，得到整個場地的下臥卵石層的埋藏深度，並給出該場地的標貫值n _ （ 63 . 5 ）與v _ r間的回歸方程，為這一方法的應用提供了很好的工程實例。 -
Formation mechanism of blow holes in plasma surface metallurgical coating
等離子表面冶金層中氣孔形成機理 -
Formation reason and prevention of blow hole on chilled surface of camshaft
凸輪軸激冷麵氣孔成因及防止方法的探討 -
Brush or blow off the finned surface of the condenser monthly
每月擦拭或. .冷凝器的翅片表面。 -
Use a rubber blower ( commercially available ) to carefully blow away any dust on the surface of the cmos sensor
使用橡膠皮吹（可以在攝像商店裡買到）小心的吹走任何附著在cmos處理器上的灰塵。
分享友人