transmitting power 中文意思是什麼

transmitting power 解釋
發射功率
  • power : n 1 力,力量;能力;體力,精力;(生理)機能;〈常 pl 〉才能。2 勢力,權力,權限;威力;政權;權...
  1. The transmitting noise can reduce capability of power supply or attaint switch power supply

    由於傳導型噪聲會降低直流開關電源的性能,嚴重時會造成直流開關電源的損壞。
  2. Widely employed in coal mine, downhole coal bunker, coal washery, cement factory, foundary, thermal power plant, sintering plant coal gas factory, fertilizer plant, chemicals plant, aluminium plant, alkali factory, steel works, coking plant, pharmaceutical factory, mine, dock, foodstuff, and feedings process works, concrete process, etc. with bunker, hopper, transmitting pipeline and drawshaft

    廣泛用於煤礦、及井下煤倉、洗煤廠、水泥廠、鑄造廠、火力發電廠、燒結廠、煤氣廠、化肥廠、化工廠、鋁廠、制堿廠、鋼鐵廠、焦化廠、制藥廠、礦山、碼頭、糧食、飼料加工廠、混凝土加工廠等擁有料倉、料斗、輸送管道和礦山溜井的廠礦企業。
  3. Technique of transmitting data via power line ( pl ) , a new technique developed in recent years , is used to automatize the free collecting system in public service and the management of uptown service 。 this article discussed the advantage , disadvantage and the current state of the power line carrier communication 。 the advantage , method and current state of using spread spectrum technique in power line communication are discussed 。 then the characteristic of low voltage power network was also compendious analyzed 。 in this paper , after introducing the principle of ssc , design of hardware and software of the system are been discussed 。 this system has been put into use , the result has proved its high stability and reliability

    本文研究旨在提供一種利用低壓電力供電網路、低成本、高可靠地實現公共事業收費自動化和小區物業管理智能化的技術應用。討論了電力線載波通信的優、缺點及現狀,擴頻技術在電力線載波通信應用的優點、方式和現狀,並對低壓電力線網路的特性進行了簡單的分析。在闡述了擴頻通信的基本原理的基礎上,本文詳細地介紹了電力載波遠程抄表系統的具體實現,包括硬體模塊和管理軟體本系統已投入運行,具有較高的穩定性和可靠性。
  4. Furthermore, it is important propagandizing tool because it is the pivotal and integrant component of the super - high power broadcast and television transmitting equipment it has very

    更為重要的是,它是國家的重要宣傳工具? ?超大功率廣播電視發射機必須的關鍵器件,它的研製成功具有十分重要的政治意義。
  5. Based on the analysis of the effect on the maximum range of the equation ' s each parameter and the traditional method of extinction ratio, the noncooperative regulable attenuation - measure the minimum detectable power of laser altimeter on the condition of constant miss probability by attenuating the laser power transmitting to the diffuse reflected simulant target - was put forward

    在傳統的消光系數法基礎上,根據對月測距方程各系數的影響權重分析,提出了非合作目標可調衰減法,即:通過對漫反射模擬目標,衰減出射激光功率,在一定的漏警概率條件下測量激光高度計的最小可探測功率。
  6. Compared with current instruments, the setup can decrease disturbance of disorder radiation by using double layer refractive index sample matching vessel, and it can increase collecting and transmitting efficiency of radiation by adopting single mode fiber with gradient refractive index lens. with a low power laser, the sample has a low scathe, and the laser and the measurement system can be integrated conveniently

    與現有的同類型儀器相比,該儀器採用雙層折射率樣品匹配池減少了雜散光的干擾;採用帶梯度折射率透鏡的單模光纖接收、傳輸散射光信號提高了散射光的收集傳輸效率;用低強度的激光避免了對樣品的輻射損傷,同時可以使激光器和系統集成在一起,整個系統小型實用。
  7. This paper presents our research in actuating in - vivo micro - robot based on the capsule endoscope platform by the external power. while seeking secure driving method we take several factors into account, such as driving environment, power transmitting and consuming, motion requirement and controllability, and locating technique. we mainly deal with driving the capsule with spatial gradient magnetic field, so we employ combined electro - magnetic coils, including gradient coils and homogenous coils, which have rotational dof around a translatable patient bed, to compose a controllable uniform gradient which act on the permanent - magnet embedded robot, thereby get an appropriate spatial force and torque to fulfill the anticipant locomotion such as move, stop, pitch and yaw

    基於驅動環境、能量供給和消耗、驅動動作要求及驅動安全性與可控性,定位方案等多方面考慮,尋求安全可靠的腸胃檢查微機器人的外部驅動控制方法,並著重研究直接利用外磁場磁力驅動微機器人:在微機器人內部嵌入永磁性體,利用體外的組合電磁線圈產生加載電流控制的驅動磁場,其中外部的電磁線圈由多組梯度線圈和勻場線圈組合構成,通過繞病床的旋轉以及病床的平移共同控制微機器人所在位置的磁場強度及梯度,作用於微機器人內嵌磁體以獲得空間意義上的必要驅動力和調整轉矩,從而有效地完成驅動動作要求。
  8. The company founded quality quality system certificate of conformity by iso9002 standard districtly. and pass iso9002 quality system certificate of conformity of shanghai auditing center of quality system the truth of our company is creating eternal satiafication by fine product and excellent service. huaqing bare wire power cable control cable purpose jacketed cable insulated wire xlpe cable fire - resistant cable requence - transmitting cable pass each kinds of inspection and appraisement of china and province. each index attain nation advanced level, and gain praise conformably of all consumer, such as power, oil, architecture. originally founded in 1986, qingdao jiaozhou cable co. ltd., whose original name is jiaozhou city cable factory, finished the enterprise reformation and founded the limited liability company in 1998

    公司的前身膠州市電纜廠,是一九八六年建立的膠州市第一家電纜企業,經過多年的努力,企業榮獲了青島市「明星企業」 「百強企業」 「先進企業」 「優秀企業」 「重合同守信譽企業」 ,全國中型電纜行業「質量信譽最佳企業」國家經貿委城鄉電網改造「推薦企業」 ,國家廣電總局「器材入網單位」等多項榮譽稱號及證書。
  9. Hong kong matters not only because it is a vital driveshaft of the global economy, transmitting the raw power of china ' s manufacturing capability into a worldwide system for distributing consumer goods

    香港的問題的不只是因為它是全球經濟的一個至關重要的運行軸,同時也正將中國尚未開化出來的在生活消費品分佈方面的的製造能力帶入到世界體系中。
  10. The problem about neutral - point - grounding mode is an all - around technical problem which associated with not only power system reliability , insulation coordination , electromagnetic interference , but assault safety 。 in china , the neutral grounding modes of the 10kv net involved of none grounding, grounding by arc suppressing coils, resistance grounding or reactance grounding in the past 。 with the development of civic power network , low resistance grounding mode was used to restrain the over voltage, particularly in guangzhou, shanghai , beijing , and zhuhai etc. it was reported that the over - voltage level of low resistance grounding mode is lower than that of arc suppressing coil mode, but the operation carried out the other way 。 at substations in guangzhou and shanghai it was found that the low resistance grounding mode is successful 。 but in some areas , such as zhuhai , substations grounding with low resistance revealed some problems , including power supply reliability rapidly dropping , transmitting line often tripping ; and person safety being threatened 。 so interiorly the grounding mode selection of the 10kv network was disputed, which mainly focused on the fault form of 10kv net grounding, the apply area of suppressing arcing coil grounding mode, power supply reliability level of the two modes, person safety, communication interfere and the workload of maintenance

    爭議點主要是在10kv電網接地故障的形式、消弧線圈接地的應用范圍、兩種運行方式供電可靠性的高低、人身安全、通訊干擾和運行維護工作量等諸多方面。 11 17本論文就是針對以電纜為主的城區10kv電網中性點接地方式的選擇問題進行研究。論文首先對10kv電網的中性點運行各種方式進行分析,比較各方式的特點,然後以重慶儲奇門變電站10kv電網的實際參數來建立數值計算模型,在考慮了電網接地電容電流變化、中性點電阻取值大小、接地點接地電阻值變化等多種影響因素的情況下,對中性點經消弧線圈接地和經小電阻接地方式下電網的過電壓水平和接地點短路電流大小進行了數值計算,其計算結果與電科院所作現場試驗進行了比較。
  11. Based on calculating and comparing with the transmission ratio, transmitting efficiency and power flow of the transmission plans in the controllable initation planet gear device referred in the literatures, the best reasonable solution was confirmed which can reduce the device dimensions and improve the transmission efficiency

    摘要在對已有文獻提出的可控制起動行星齒輪減速裝置傳動方案從傳動比、傳動效率及功率流向等方面進行計算與比較的基礎上,確定了能夠使減速器裝置的整體尺寸小、外形美觀、傳動效率高的最合理方案。
  12. Transmitting noise is main interfereing source of switch power supply which is coupled through lines of power supply, singal, interlinkage and grouding

    摘要傳導型噪聲是開關電源的主要騷擾源,它可以通過電源線、信號線、互連線、接地導體等進行耦舍。
  13. 3. with comprehensive improvement of transponder including structural adjustment to lna ; optimization of ( phase locked loop ) pll filter ; structural adjustment to the transmitter and phase error adjustment to the intermediate frequency demodulation circuit, we have successfully enhanced sensitivity, expanded dynamic range, increased transmitting power and improved the spectrum purity ; decreased capture time for pll ; improved the signal quality after demodulation ; reduced its volume and power consumption. 4

    3 、對通信機的全面改進,包括lna結構的調整、鎖相環環路濾波器的優化、發射部分結構的調整以及中頻解調電路的相差調整,提高了系統的接收靈敏度、改善了本振的頻譜純度、減少了鎖相環的鎖定時間、使中頻解調后的信號質量大為提高,同時還減少了體積、節約了系統的功耗。
  14. Being master control part, user controller stores, manages, display and query user information ; as slave control part, sub - user controller calculates and temporarily stores power sent from measuring module ; measuring module measures electric energy by using power meter ' s special circuit which simplifies circuit design and connects or breaks up power supply circuit by relay ; in order to transmitting data fast and exactly, rs - 485 communication standard is adopts between user controller and sub - user controller

    主控部分用戶控制模塊可存儲、管理、顯示和查詢用戶電能信息;從控部分子用戶控制模塊計算並暫存電能測量模塊輸出功率數據;電能計量模塊採用電度表專用厚膜電路hdb6進行電能計量,簡化了電路設計,同時還利用繼電器控制連接或斷開用戶的供電迴路;在主從部分間採用rs - 485通信標準實現數據快速、準確的傳輸。
  15. ( 5 ) from august, 2002 to april, 2003, on the base of analyzing of 10kw valve tv transmitter of channel 14, chongqing tv transmitting station, brought forward process the solidification scheme to 400w valve power amplifier of the driver

    重慶大學碩士學位論文中文摘要( 5 ) 2002年8月至2003年4月期間,在對重慶電視發射臺14頻道( uhf ) 10kw電子管電視發射機進行研究分析的基礎上,提出了對該機末前級400w電子管功率放大器進行固態化改造的方案並予以實施。
  16. On the base of summarizing and reference to the achievement of uhf complete solid - state high - frequency power amplifier abroad, the author have made a deep research in uhf 10kw electron tube tv transmitter power amplifiers which are widely used inland, and asked for ideas of a lot of engineers of chongqing tv transmitting station, brought forward a practicable solidification scheme under the guidance of prof. gao chao and prof. guoyongcai, and made a successful practice at chongqing tv transmitting station

    筆者在總結和借鑒國內外有關uhf全固態電視發射機高頻線性功率放大器研究成果的基礎上,對目前國內電視發射臺普遍採用的uhf10kw電子管電視發射機高頻線性功率放大器進行了深入研究,並廣泛徵求重慶電視發射臺工程師的意見,在重慶大學高潮教授和郭永彩教授的指導下,提出了切實可行的固態化改造方案,並在重慶電視發射臺實踐成功。
  17. The fourth, the power capacity and the special harmfulness of ghost mode resonance when a cylindrical box type window is used to transmit high power cw are studied in detail. the existing formula for calculating the average transmitting power capacity of cylindrical te11 mode box type window is revised and a formula for three dimensions simulation computation of the temperature increment of the dielectric disk in cylindrical te11 mode box type window is deduced

    第四,對圓柱盒型窗用於傳輸高功率連續波時的功率容限和鬼模振蕩的特殊危害性等問題進行了深入的研究,修正了現有的圓柱te _ ( 11 )模盒型窗的平均傳輸功率容限的計算公式,並推導出了可用於三維模擬計算的圓柱te _ ( 11 )模盒型窗中介質窗片溫升量的計算公式。
  18. Space - time coding technology is based on multi - elements antenna array and has strong points of both time processing and space processing. it can satisfy the requirements of high data rate transmission in the future radio mobile system without the increase of the transmitting power and the spread of the frequency. and it can greatly improve the quality of communication services and system capacity under fading channels

    空時編碼技術是一種利用多天線陣發送和接收的技術,該技術能很好地結合時間處理技術和空間處理技術的特點,能在不增大發射功率和不擴展頻帶的前提下滿足未來無線移動通信對高數據率傳輸的要求,從而全面提高衰落通道的通信質量和通信系統容量。
  19. Transmitting power monitor

    發射功率監測器
  20. Transmitting power : 50mw

    發射功率50mw
分享友人