延性極限 的英文怎麼說

中文拼音 [yánxìngjíxiàn]
延性極限 英文
ductility limits
  • 性 : Ⅰ名詞1 （性格） nature; character; disposition 2 （性能; 性質） property; quality 3 （性別） sex ...
  • 極 : i 名詞1 （頂點; 盡頭） the utmost point; extreme 2 （地球的南北兩端; 磁體的兩端; 電源或電器上電流...
  • 限 : Ⅰ名詞（指定的范圍; 限度） limit; bounds Ⅱ動詞（指定范圍, 不許超過） set a limit; limit; restrict
  • 極限 : 1 （最高的限度） the limit; the maximum; the ultimate limit; limitation; extremity; tipping point...
  1. Here the hsc of sompa is achieved through adding super - effective water reducer, fined slag and silicon fume, and decreasing the water / cement ratio. by varying the area ( spacing ) of tension bars, compressive bars, vertical links and distribution steel and embedding steel fiber and polypropylene fiber we try to improve the behaviors of reinforced high performance concrete one - way spanning slabs in bending, so that its ductility be greater than 5. with the same arrangement of steel the width of bending member is varied to observe the effect of the width / depth ratio on the ultimate compressive strain of concrete

    通過變化受拉筋含筋率和受壓筋、箍筋（鉤筋、分佈筋）含量，或摻加纖維使之成為鋼纖維高強混凝土（ sfrhsc ）和聚丙烯纖維高強混凝土（ pfrhsc ） ，對高強混凝土雙筋截面梁、板的受彎性能進行了試驗研究，試圖改善高強混凝土受彎構件的延性，使其延性比大於5 ；並在相同配筋情況下，通過變化截面寬度，研究了高強混凝土受彎構件的寬高比對壓區混凝土極限應變的影響；並對試驗構件的裂縫發展情況進行了觀測。
  2. The research shows that : 1 ) the ductility of the hsc bending members constructed is much greater than 5 ; 2 ) increasing the vertical links and distribution steel can increase the deflection under ultimate moment ; 3 ) with appropriate compressive bars, vertical links and distribution steel the increase of moment after yield and the decrease of moment under ultimate moment can be ignored, so the ductility of the hsc bending member is much larger ; 3 ) the width / depth ratio of hsc bending member has no obvious effect on the ultimate compressive strain of concrete ; 4 ) the method used here to calculate the deflection is applicable ; 5 ) the location of crack coincides with the location of vertical links and distribution steel ; 6 ) the bending property of the hsc structure under the blast load can meet the demand of protective engineering

    研究表明：本文研究的梁、板構件的延性比遠大於5 ；增加箍筋（鉤筋、分佈筋）含量，可以提高壓區混凝土剝落時的撓度；在適當的受壓筋、箍筋（鉤筋、分佈筋）含量下，可以忽略壓區混凝土剝落瞬間的承載力下降，從而大大提高構件的延性；受彎構件的寬高比對壓區混凝土極限應變的影響不明顯；受彎構件的裂縫間距受箍筋（鉤筋、分佈筋）的布置影響；文中所用的承載力和變形計算方法是可行的。化爆試驗表明，高強混凝土構件的動載抗彎性能能夠滿足防護結構的要求。
  3. By maintaining and strengthening, the existing fault bridge strengthened the total intensity and rigidity of the main girder, to large extend. the strengthened bridge could lengthen its service life and made deck line state, ultimate bearing capacity and durability, and so on, attain to design standard

    對既有病橋進行加固維護，能大大地增強主梁的整體強度、剛度，延長橋梁的使用壽命，使其橋面線形、極限承載能力和耐久性等達到設計要求。
  4. According to these, applying the virtual work theory, this paper analyzed the influence of active beam link on the terminal carrying capacity, stiffness and ductibility of three types of ebsf

    接著在此基礎上應用虛功原理，分別研究了耗能梁段長度對d型、 k型和v型三種偏心支撐框架的極限承載力、剛度以及延性的影響。
  5. Similarly, according to the deformation mechanism of ebsf and the virtual work theory, the influence of three different active beam links on the terminal carrying capacity, stiffness and ductibility of ebsf is deducted

    同樣，根據偏心支撐框架的幾何變形機制，應用虛功原理，重點推導並分析比較了分別採用d型、 k型或者v型支撐時對結構的極限承載力、彈性剛度以及延性的不同影響。
  6. Its hysteretic curve is plumper, its ductility coefficient and energy dissipation capacity have been improved remarkably. the inclined staff of the steel bar truss has a restraining faction to the development of the crack, and the phenomena is that there has more crak and larger distributing area on the shear wall, which is an important token of the improved seismic capacity. concealed steel bar truss has the faction of increasing the height of plastic hinge area, which is another important token of

    研究結果表明:內藏鋼桁架高剪力墻與普通高剪力墻相比:屈服荷載和極限荷載均比顯著提高;屈服剛度明顯提高;其滯回環相對飽滿，延性系數及耗能能力顯著提高;內藏鋼桁架高剪力墻，其鋼桁架斜桿對裂縫發展有控製作用，現象是墻體上的裂縫較多、分佈域較廣，這是抗震耗能能力增強的重要表徵;內藏鋼桁架高剪力墻有增大底部塑性耗能區域的作用，這是抗震耗能能力增強的另一重要表徵;內藏鋼桁架還有顯著提高抵抗剪力墻基地剪切滑移能力的作用。
  7. Taking an ultimate deflection more than 1 / 50 of calculating span as the determinant term, by the means of numerical analysis and regress equation respectively, this paper discusses the reasonable stretching controlling stress of usual span and reinforcement slabs for design reference

    以極限撓度達到跨度的1 50作為延性破壞的判定指標，本文分別運用數值分析程序試算和回歸方程得出了常用跨度、常用配筋的中強（ 1270mpa ）螺旋肋鋼絲預應力混凝土空心板的張拉控制應力的取值，供設計參考。
  8. Though much progress has been achieved in previous study, there still remains a lot to be studied and perfected. the thesis is devoted to study on the multi - ribbed slab wall, the main bearing member in mrss, including its mechanism, failure mode, aseismic capability, mechanical models, ultimate bearing capacity and aseismic design based on control. the paper mainly accomplished such work as follows : 1 ) based on test research on multi - ribbed slab wall, the paper proposed the member ' s failure modes under horizontal loads, analyzed the co - performance between the inner frame and the infilled silica bricks and that between the slab and the outer frame, discussed the wall ' s bearing capacity, rigidity, deformation, ductility and energy dissipation ability in different modes, and put forward a simplified mechanical model of the slab wall under vertical loads

    本文針對密肋壁板結構的主要受力構件? ?密肋復合墻體為研究對象，就其受力機理、破壞模式、抗震性能、三階段力學模型、極限承載能力以及基於控制的抗震設計方法等進行了較為詳細的研究，完成的主要工作有： 1 ）通過對密肋復合墻體在水平低周反復荷載和單調荷載作用下的試驗研究，提出了墻體的主要破壞模式；分析了框格與內部填充砌塊、墻板與外框的共同工作的受力特點；探討了不同破壞模式情況下墻體的承載能力、剛度、變形、延性、耗能等抗震性能，並給出了豎向荷載作用下密肋復合墻體的簡化力學模型。
  9. The results indicate that the different construction methods will have influence on the mode of the internal force redistribution, however, the methods will not cause influence on the mode of structure failure, and the ductility of the final structure will make the ultimate bearing capacity of the beams cast by the different methods get close to an identity

    結果表明：不同施工方法會影響內力重分佈的模式，但不影響結構的破壞模式，最終結構的延性將使不同施工方法梁的極限承載力趨近一致。
  10. A completely new makeup experience, compound of high shine converge ingredient, just sweep lightly, the soft and elastic rising fibre will spread according to the direction of eyelash, magic breach limitation and length

    一種全新的上妝體驗，高光澤聚合成分延展拉伸復合物，只需輕輕一掃，柔軟而極富彈性的增長纖維，即會沿著睫毛方向順勢延展，美睫魔幻般突破極限，無境纖長。
  11. Tow speciments of prestressed fabricated beam - column subassembly were tested under reversed cyclic loading. experimental studies were carried out to investigate the strain distribution, failure mechanism and load - bearing capacity on the beam - column connections, as well as ductility, hysteresis curves energy dissipation, displacement restoring capacity of full pc speciments

    本文通過兩榀預壓裝配式樑柱組合體在低周反復荷載下的試驗，了解了預壓裝配式框架梁端截面應變分佈、破壞機理和極限承載能力；探討了全預應力配筋截面延性特徵、滯回性能、耗能能力和變形恢復能力。
  12. The limit behavior of a class of nonlinear time series model with stochastic delay

    一類帶隨機延滯的非線性時間序列模型的極限行為
  13. Ltd. a coupled vibration method on suspended free poles is employed to determine the initial young ' s modulus at elevated temperatures, also the thermal expansion coefficients of fire - resistant steel

    通過高溫下的恆溫加載拉伸試驗，得到不同溫度下耐火鋼的屈服強度、極限強度、延伸率、面縮率和應力應變關系，並測定高溫下耐火鋼的熱膨脹系數，採用懸絲耦合共振法測定高溫下耐火鋼的初始彈性模量。
  14. Research on 3d fem prediction of sheet metal forming limit based on ductile fracture criterion

    基於延性斷裂準則的板料破裂極限三維有限元預測方法研究
  15. The result of macro - quality experiments show : mineral admixtures markedly slow the hydrating velocity of cement slurry, decrease and delay the hydrating max - temperature, in which steel slag is more effective ; expansive agents compensate concrete shrinkage, enhance the concrete dense degree, strengthen the interfacial layer between fiber and cement matrix and improve the physical mechanics qualities of acic ; minimal admixtures markedly improve the concrete workability property, increase the concrete later intensity & density and the capability of anti - chemical attack and anti - permeability ; hybrid fiber reinforces the toughness of obviously acic by the means of anti - cracking effect of fiber with different sizes and different properties in the corresponding construction levels

    實驗結果顯示：鋼渣摻合料能顯著減緩水泥漿體水化速率，降低砂漿的水化溫升並延遲最高溫升時間；補償混凝土收縮，提高混凝土密實度，加強纖維與水泥石的界面粘結，增強混凝土力學性能，但不能明顯改善混凝土韌性。混雜纖維通過纖維的不同尺度與不同性質在相應的結構層次上產生阻裂效應，增韌鋼渣防滲抗裂混凝土；增加混凝土的破壞極限能，極大提高混凝土抗彎曲能力和韌性指數，改善混凝土脆性。
  16. In this paper, we compare two kinds of local maps. from the anti - integrability limit, we study the question whether the equilibria at the anti - integrability limit can persist or not with growing coupling coefficient e

    我們在這篇文章里主要比較兩類性質不同的局部函數，從反可積的極限出發，隨著耦合系數的增大，討論平衡解的延拓和分支。
  17. This paper has put forward such one, i. e. to use the dimensional angle iron framework to strengthen the center of the knot in order to add its degree of toughness and stiffness, improve its crack load and aggrandize its ultimate deformation

    本文提出了一種提高節點抗震性能的新方法? ?用空間角鋼骨架對節點核心區進行加強，以增大節點的強度、剛度，提高節點的抗剪、抗裂性能，並增大節點的極限變形能力及延性性能。
  18. In this dissertation, the fact that the concepts of tangent modulus factor ( _ ( 1 ), ), proportional limit law ( pll ) and strength utilization ratio function ( surf ) in the combined theory of strength and stability ( ctss ) are the extension of concerned concepts in elastic mechanics is illustrated

    本文說明了強度穩定綜合理論中的切線模量因子、比例極限定律和強度利用率函數等概念是彈性力學有關概念的延伸，既可以用於強度理論，也可以用於穩定理論。
  19. Observing the mechanics and effect of the new strengthening method with test and finite element method is supposed to offer a guide for technology and become valuable in theory and practice. both compression test, including four reinforced and three control specimens, and shear - compression test, including nineteen reinforced and four control specimens are being studied in this paper. the research on the curves of load - strain, load - deflection and hysteretic shows that the transverse translation of the reinforced columns is well controlled with an upgrading of both ductility and ultimate bearing capacity ( ubc )

    本文對4根鋼絲網外噴高強砂漿加固鋼筋混凝土柱和3根對比鋼筋混凝土柱進行了軸壓試驗研究，並對19根加固鋼筋混凝土柱和4根對比鋼筋混凝土柱進行了剪壓試驗研究；通過對試件荷載-應變曲線、荷載-撓度曲線和滯回曲線等的研究表明，採用該加固方法能有效的約束柱子橫向變形，並對提高鋼筋混凝土柱的極限承載力和延性有明顯的效果；同時根據理論及加固機理分析提出了適應於此加固方法的軸壓極限承載力計算公式。
  20. So called ductility is the ability of transform when a structure or a chosen department of structure goes beyond the extreme of spring with no apparent degeneration

    所謂延性，是一個結構或所選擇的結構部分超越彈性極限后，在沒有明顯強度或剛度退化情況下的變形能力，即破壞之前截面或構件能承受多大的後期變形。
分享友人
分享到 Line

分享到臉書