接點閉角 的英文怎麼說

中文拼音 [jiēdiǎnbìjiǎo]
接點閉角 英文
dwell angle
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 點 : Ⅰ名詞1 （液體的小滴） drop （of liquid） 2 （細小的痕跡） spot; dot; speck 3 （漢字的筆畫「、」）...
  • 閉 : Ⅰ動詞1. （關; 合） close; shut 2. （堵塞不通） block up; obstruct; stop up Ⅱ名詞（姓氏） a surname
  • 角 : 角Ⅰ名詞1 （牛、羊、 鹿等頭上長出的堅硬的東西） horn 2 （古時軍中吹的樂器） bugle; horn 3 （形狀像...
  • 接點 : （接觸點; 連接點） contact; closing; junction; connection point; terminal pad接點電阻 contact resistance
  1. According to the special shape and operate requirements of the torpedo, the structure and moulding process of the torpedo shell are established, in which the body and overlay block with grooves are moulded by fiber winding, and close moulding respectively with the adhesive by limited stop compression. in the light of the selection of raw material system, composite system with outstanding performance are defined, based on which the mechanical properties are tested., with the overall consideration of structural characters and design demands, the main factors which may have effects on the strength and stability ( including stiffness section dimension, stiffeners space, skin thickness and skin lay angle ) is optimized one by one for the structure design parameters on the base of the fem model of skin, stiffness and layover block by fem. as a result, the prototype with 1 : 1 proportion and its structure and lay optimization design are completed. the moulding technology for polyurethane foam moulding the stiffened shell is obtai ned in terms of the design, manufacture moulding, experimental mould and tooling

    依據在研產品特殊的外型結構和使用要求，確定了該型號水雷復合材料殼體的具體結構形式和復合成型工藝路線，即由纖維纏繞工藝成型主體異形件，閉模成型帶通槽外貼塊，用限位加壓工裝實現粘接的工藝路線；通過對原材料體系的篩選，確定了綜合性能較好的復合材料體系，以此為基礎進行了力學性能測試；運用有限元方法，建立了蒙皮、筋條和外貼塊的分析模型，綜合考慮結構特點和設計要求，對影響結構強度與穩定性的主要因素（包括筋截面尺寸、筋間距、蒙皮厚度、蒙皮鋪層角度）分別進行了結構設計參數的優選，最終完成了復合材料異形耐外壓殼體1 : 1樣件和縮比實驗件結構及鋪層優化設計；完成了聚氨酯泡沫胎成型內置加筋殼體的成型工藝技術研究；對縮比件進行外壓性能測試，並給出了應力、應變測試結果。
  2. 2 ) for making the meshes consistent on the common boundaries of adjoining surfaces, a new approach of boundary discretization is employed. 3 ) the boundary - representation structure is adopted to fulfill the mesh generation over combined surfaces. 4 ) the quality of surface meshes is improved by point creation on 3d scan lines and diagonal swapping procedure

    通過引入可移動的虛邊界解決了閉合曲面的剖分問題；通過對鄰接曲面公共邊界的統一處理，保證了組合曲面拼合處網格的相容性；以邊界表示數據結構為基礎實現了三維組合曲面的全自動網格剖分；採用空間掃描線布點、診斷交換等技術，優化了網格的質量；並以autocad為支撐平臺objectarx為開發工具，開發了一個基於幾何造型的曲面三角形網格全自動生成程序。
分享友人
分享到 Line

分享到臉書