撓度測定 的英文怎麼說

中文拼音 [náodùcèdìng]
撓度測定 英文
deflection measurement
  • 撓 : 動詞1. （輕輕地抓） scratch 2. （擾亂;阻止） hinder 3. （彎曲,比喻屈服）yield;flinch:不屈不撓indomitable; unyielding
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 測 : 動詞1. （測量） survey; fathom; measure 2. （測度; 推測） conjecture; infer
  • 定 : Ⅰ形容詞1 （平靜; 穩定） calm; stable 2 （已經確定的; 不改變的） fixed; settled; established Ⅱ動詞...
  • 測定 : determine; determination; setting-out; admeasurement; assignment; assay; finding
  1. Rubber vulcanized. determination of temperature rise and resistance to fatigue in compression flexometer testing

    硫化橡膠.用壓力撓度計試驗時對溫升和抗疲勞性能的測定
  2. Rubber, vulcanized and thermoplastic - determination of temperature rise and resistance to fatigue in flexometer testing

    硫化和熱塑橡膠.撓度計試驗中溫度上升和抗疲勞性的測定
  3. Textiles glass. woven fabrics. determination of conventional flexural stifness. fixed angle flexometer method

    紡織玻璃纖維.機織織物.常規撓曲硬性的測定.用固定角度彎曲計測定方法
  4. Methods of test for adhesives - physical tests on hot - melt adhesives - determination of low temperature flexibility or cold crack temperature

    粘合劑試驗方法.第h2部分:熱熔粘合劑物理試驗.低溫撓性及冷爆裂溫度測定
  5. Road testing. measurement of a rolling load deflection. part 7 : determination of deflection and curvature values using curviameter

    路面試驗.滾動加載撓度測量.第7部分:用曲率計測定撓度和曲度值
  6. These experiments mainly aim at determining the deflection and stress of beam slab structure before and after reinforcement

    靜載試驗的內容是測定加固前後梁板結構的混凝土應力和撓度。
  7. Plastics - determination of temperature of deflection under load - part 2 : plastics and ebonite

    塑料.載荷下撓曲溫度的測定.第2部分:塑料和硬橡膠
  8. Standard test method for flexibility determination of supported adhesive films by mandrel bend

    用芯軸彎曲試驗法測定承托粘結膜撓曲度的標準試驗方法
  9. These measures included the slope horizontal displacement monitor, the supporting structure swag monitor, the subsidence monitor, the pre - stress of anchor monitor, the ribbed beam steel stress monitor. we monitored the whole process and got feedback information in time, so the trend and development of slope " s displa

    在施工過程中，我們採取了邊坡穩定性安全監測措施，主要包括邊坡水平位移觀測及支護結構撓度觀測;沉降觀測;以及錨桿應力監測;助梁鋼筋應力監測等。進行全過程的檢測並及時反饋信息，隨時掌握邊坡的位移趨勢與發展。
  10. Standard practices for making heatseals for determination of heatsealability of flexible webs as measured by seal strength

    通過測量密封強度測定撓性網熱密封性能用熔焊的標準實施規范
  11. In order to ascertain the real stress and deflection of structure this paper puts forward experimental scheme. by measuring data during the process of construction, we can know the distribution of stress in simply supported - continuous beam and compare with initial design, then we can adjust it by control method to ensure quality of the bridge

    提出具體的試驗方案，論述了測試元件的測試原理，通過測量各控制點在不同階段的應變和撓度，確定橋梁結構的實際應力大小和變形狀態，了解簡支轉預應力連續結構各跨主梁與連續處的應力分佈情況，並與設計相互驗證，通過施工控制使結構符合設計要求，保證施工質量。
  12. Flexible sheets for waterproofing - determination of length, width and straightness - part 1 : bitumen sheets for roof waterproofing

    防水撓性薄板.長度寬度和垂直度測定.第1部分:屋頂防水用瀝青氈片
  13. ( 3 ). put forward two structure scheme of opto - electronic deflection measurement sensor, light transmitting with non - mechanical scanning and light reflecting with non - mechanical scanning after compared exisiting methods of liquid level measurement to satify this needafter the comparison, an opto - electronic deflection measurement sensor based on light reflecting with non - mechanical scanning be confirmed. then the concrete design is to carry out, which includes the design of reflective surface, the design of pds ( photo detective subassembly ) ' s bracket, the design of floater and the design of shaking - absorbed accessory. during the process, there are a series of caculations and emulations. at last, the opto - electronic deflection measurement sensor has been designed and produced

    比較了現有液位測量方法后提出了能夠滿足大佛寺長江大橋撓度測量要求的基於連通管的光電撓度計的非機械掃描光透射式和非機械掃描光反射式的兩種方案，通過比較確定了非機械掃描光反射式方案。隨后通過對該方案進行具體的零件設計，主要包括反射面的設計， pds （光電接收組件）支架的設計，浮子的設計以及減震零件的設計等等，在設計的過程中包含了一些理論計算和模擬，最終設計和製作了光電撓度計。
  14. To our satisfaction, all the measuring results from the measurement locale are accurate and convincing comppared with the results calculated by the theory which makes it clear that the system can meet the demands of measuring upon the dafosi bridge of changjiang river. the system has achieved the long - time and real - time automatic deflection measurement of the bridge at first time in our country, and the system has passed the appraisal of the experts consigned by the ministry of communications so the system has the practical value on the long - span bridge ' s deflection measurement

    通過對橋梁實際測量結果與理論計算的結果的對比分析可知，本文所設計的連通管式光電撓度測量系統測量數據準確，系統可靠，能夠滿足大佛寺長江大橋撓度測量的需要。該撓度測量系統首次在國內實現了橋梁主梁撓度的長期實時自動監測，並且已經通過了交通部的項目驗收，具有一定的推廣價值
  15. Tests relating to pavements. measurement of a rolling load deflection. part 2 : determination of deflection and curvature values using modified behkelman beam

    路面試驗.滾動加載撓度測量.第2部分:用改進的貝克曼量儀測定撓度和曲率值
  16. Advanced technical ceramics. mechanical properties of ceramic composites at high temperature under inert atmosphere. determination of flexural strength

    高技術陶瓷.惰性大氣高溫情況下陶瓷復合物機械性能.撓性強度測定
  17. Methods of testing plastics - thermal properties - determination of cold bend temperature of flexible polyvinyl chloride extrusion compound

    塑料試驗方法.第1部分:熱性能.撓性聚氯乙烯擠壓混合物冷彎溫度測定
  18. Methods of test for screed materials - part 2 : determination of flexural and compressive strength

    找平層材料試驗方法.第2部分:撓曲強度和抗壓強度測定
  19. Methods of testing plastics - thermal properties - determination of stiffness in torsion of flexible materials general method

    塑料試驗方法.第1部分:熱性能.方法153a :撓性材料抗扭剛度測定
  20. Methods of testing plastics - thermal properties - determination of stiffness in torsion of flexible materials method for vinyl chloride compounds

    塑料試驗方法.第1部分:熱性能.方法153b :撓性材料抗扭剛度測定
分享友人
分享到 Line

分享到臉書