擺角 的英文怎麼說

中文拼音 [bǎijiǎo]
擺角 英文
angle of cant
  • 擺 : Ⅰ動詞1 （安放; 排列） put; arrange; set in order 2 （顯示; 炫耀） display; show off; put on; assu...
  • 角 : 角Ⅰ名詞1 （牛、羊、 鹿等頭上長出的堅硬的東西） horn 2 （古時軍中吹的樂器） bugle; horn 3 （形狀像...
  1. Image coordinate and galvanometer pendular angle are kept in the computer according to the f9 field lens characteristic, enter pupil excursion and f6 characteristic error are ignored, that the image of laser scanning point move acceding to unlinearity relation is deduced theoretically. for deducing the distortion, error compensation is considered in the software

    像點坐標與振鏡擺角按f物鏡特性的線性關系存儲在計算機，在忽略了入瞳漂移和f特性誤差后，從理論上推導出二維垂直振鏡分佈中激光束掃描點的像點按照復雜的非線性關系運動，為了減少幾何畸變，在軟體設計中給出誤差補償。
  2. Max. swing angle of steering pitman arm

    轉向搖臂最大擺角
  3. The available maximum rolling angle of the platform is 30 and in the experiment the maximum rolling angle 10, 15, 20 was chosen. the rolling period of the platform is selected with 5 second, 7. 5 second and 10 second

    實驗中選定最大搖擺角度為10 、 15和20 ，搖擺周期為5秒、 7 . 5秒以及10秒，以及一些分離周期值。
  4. According to the designing plan, the mathematical model of spherical pendulum is more simplified in two aspects, and the results we get has the same form with the mathematical model of simple pendulum. then a rule of kinematical of pendulum in relative coordinate is gotten

    本文根據方案中遇到的主要工況將球面擺的數學模型進一步簡化為兩個主運動方向上的擺動的運動微分方程，簡化結果與單擺的數學模型一致，得到了擺錘在相對坐標中擺角的變化規律。
  5. Mainly used in wind guiding part, hand moving part of fan and all kinds of craftwork, lamps and lanterns and toys, wind direction motor of air conditioner and turnplate motor of microwave oven

    主要用於電風扇的導風機構搖頭機構取暖器擺角以及各類工藝品燈具玩具等用具上。以及各類空調的風向電機和微波爐的轉盤電機。
  6. Mainly used for wind guiding part, hand moving part of fan and all kinds of craftwork, lamps and lanterns and toys, wind direction motor of air conditioner and turnplate motor of microwave oven

    主要用於電風扇的導風機構搖頭機構，取暖器暖風機小太陽擺角，各類工藝品燈具玩具等用具以及各類空調的風頁導向電機和微波爐的轉盤電機。
  7. By comprehensive considerate the intercoupling relationship between the side - slip angle and the yaw rate, the combine - control strategy ’ s predominance distinctness because it overcome the disadvantages of the large side - slip angle under the - control and can ’ t following the ideal yaw rate under the - control. vehicle possesses optimal control stability with the combine - control obviously

    由於聯合控制策略綜合考慮了質心側偏角和橫擺角速度之間相互耦合的關系，克服了單獨橫擺角速度控制時質心側偏角過大，以及單獨質心側偏角控制時對理想橫擺角速度跟蹤不好的缺點，因而優勢明顯，聯合控制策略下的車輛具有最佳的操縱穩定性。
  8. Comparison and design of two different deflection angle measurement system for a 2 dof laser scanner

    兩種二維激光掃描器擺角測量方法的比較和實現
  9. Swing angle, ring rig

    鑿孔深度鉆架前後擺角
  10. On controlling double - oscillationed - axis - cutting - tool structural - virtual - axis machine tool

    一種雙擺角刀具結構虛軸機床的控制問題研究
  11. By experiment, the input - output characteristic of the liquid angular sensor is given

    並通過實驗，給出液體擺角傳感器的輸入?輸出特性曲線。
  12. The equation of motion is linearized near the equilibrium position of the tethered mass system

    基於小擺角假設，將系統運動微分方程在平衡位置附近線性化。
  13. The endpoint is similarly located by measuring clockwise from the starting point by the number of degrees in the sweep angle

    定位終結點的方法與之類似，從起始點順時針測量擺角的度數。
  14. While the maximal angle is just 88 of the famous flexible wrist of trallfa when the input angle are equivalent to it

    而在輸入擺角相同時，國外著名的trallfa柔性手腕的最大偏擺角度只有88 。
  15. If the sweep angle is greater than 360 degrees or less than - 360 degrees, the arc is swept by exactly 360 degrees or - 360 degrees, respectively

    如果擺角大於360度或小於- 360度，則弧線將只分別掃過360度或- 360度。
  16. Abstract : the construction of the liquid angular sensor in the laser beacon is designed, the work principle and magnify circuit are analysed

    文摘:對激光基準信標儀中所採用的液體擺角傳感器的結構進行設計，分析其工作原理、放大電路。
  17. Aimed at the equal - diameter cam mechanism with follower of planar movement, and according to two conditions of existing meaningful solution of the mechanism and of ensuring transmission angle of output swinging rod, the value selection ranges of cam motion angle, of swinging angle of out - put swinging rod and of its primary installation angle were analyzed and determined, and then proceed to plot the region graph of selectable value for motion angle of cam and swinging angle of swinging rod, thus provided convenience for the design and employment of that mechanism

    摘要針對平面運動從動件等徑凸輪機構，根據機構存在有意義解和保證輸出擺桿傳動角兩個條件，分析並確定了凸輪運動角、輸出擺桿擺角及其初始安裝角的取值范圍，進而繪制了凸輪運動角與擺桿擺角的可選值域圖，為該機構的設計與使用提供了方便。
  18. At the end, the vibration responses are displayed in polar diagram synthetically, in which the displacement, the static offset and the deflection angle of rotor could be shown altogether

    提出用極坐標表徵轉子振動特性的方法，可以更直觀、全面地反映轉子的振動幅度、機動飛行時的靜態偏移以及偏擺角。
  19. The polar coordinates of tool swinging pivot are figured out, and the expressions of tool swinging and the variable - speed of spindle are derived

    通過對凸輪車削的運動關系進行分析計算，推導出在恆角度與恆速度切削的情況下，刀具擺角、機床主軸轉速與凸輪轉角位置的關系，為在實際中應用提供了理論依據。
  20. So it can be concluded that the rolling condition weaken the stability of the system

    而最大搖擺角度與搖擺周期對系統穩定性的影響趨勢並不是單一的。
分享友人
分享到 Line

分享到臉書