最大過沖 的英文怎麼說

中文拼音 [zuìdàguòchōng]
最大過沖 英文
maximum overshoot
  • 最 : 副詞（表示某種屬性超過所有同類的人或事物） most; best; worst; first; very; least; above all; -est
  • 過 : 過Ⅰ動詞[口語] （超越） go beyond the limit; undue; excessiveⅡ名詞（姓氏） a surname
  1. By using the processing method of sliding time window, the problem of the periodicity range ambiguity is solved. meanwhile, the problem of range ambiguity which is produced because the range of target is biger than the maximum range of radar is also solved by using this method. then, the pulse width parameter which is the most important in the parameters of fmicw is analyzed. the stricter restrict is given to ensure the range spectrum has only one beat frequency after signal processing. at last this thesis introduces the different signal processing methods of fmpcw and fmicw

    同時利用該方法解決了fmpcw信號的由於目標距離超過雷達的最大單值測距范圍而引起的距離模糊問題。然後對fmicw波形參數中最為重要的脈沖寬度進行了分析，給出了更為嚴格的約束條件，保證了信號處理后距離譜峰值的唯一性。最後，分別介紹了fmpcw和fmicw信號的不同處理方式，並對兩者不同的時域濾波性能進行了比較，並對二者的差異進行了分析。
  2. In present dissertation, most stirpses are repartitioned and redefined, and the structure characteristic, course of formation, cause of formation, function and risk of stirpses are analyzed. the main conclusions are : [ 1 ] rapid development of corporations engenders urgent demand of financing, conflict between capital market imperfection and demand of financing leads corporations to control listed corporations by purchasing " shell " and enhance it ' s financing capability ; [ 2 ] two kinds of pricing institution of stock provides stirpses for controlling listed corporations by low cost, monitoring institution imperfections provides corporations for operating listed corporations. adjust of national assets provides more " shells " ; [ 3 ] more private corporations purchase listed corporations, some of them form stirpses ; [ 4 ] stirpses have positive influence about adjusting industry and enhancing capital market financing function ; [ 5 ] stirpses magnify financial risk by controlling listed corporations, and transform listed corporations from shareholders benefit to block shareholder benefit, having tendency of infracting shareholders benefit

    本文主要的結論： [ 1 ]中國企業的迅速發展對融資有迫切的要求，中國國內資本市場發展不完善與這種強烈的融資需求的沖突導致了企業尋求通過買「殼」的方式控制上市公司，以此來提高自身的融資能力； [ 2 ]中國上市公司股票的兩種定價機制為「系」低成本控制上市公司提供了可能，監管機制的不完善為「系」提供了操縱上市公司的空間，國有資產在調整過程中從部分競爭行業退出，為資本市場提供了一定數量的「殼」資源； [ 3 ]民營企業紛紛買「殼」上市，在這個過程中，部分實力突出的企業形成了「系」 ； [ 4 ] 「系」現象對進行行業整合、提高資本市場融資能力等方面起到了積極的作用； [ 5 ] 「系」通過對上市公司進行的操縱放大了金融風險，將上市公司的股東利益最大化變為大股東利益最大化，存在著侵害小股東利益的潛在傾向。
  3. In view of this situation this article has conducted research to the design of metallurgy auxiliary biography with the frequency conversion table electrical machinery first multianalysis to the frequency changer and the frequency conversion table electrical machinery movement characteristic is carried out, the voltage waveform harmonious which the frequency changer outputs is big, attacks in a big way, and the voltage climbing rate reaches as high as 6600v / mu s which is 20 times ordinary sine alternating voltage, the rolling mill auxiliary biography table set the extremely strict request to the electrical machinery ; its movement frequency is very low, rate frequency in 8 - 20hz ; the velocity modulation scope is wide, the lowest movement frequency lowers to 1hz, and the starting number of times is quite frequently, each hour reaches as high as 600 - 800 time, the impact shoulders in a big way, the overload capacity request is high

    針對這一情況本文對冶金輔傳用變頻輥道電機的設計進行了系統研究。首先對變頻器和變頻輥道電機的運行特性進行詳細分析，變頻器輸出的電壓波形諧波大，沖擊大，電壓上升率高達6600v / s ，是普通正弦交流電壓的20倍;軋機輔傳輥道對電機提出了十分嚴格的要求:其運行頻率很低，額定頻率在8 - 20hz ;調速范圍寬，最低運行頻率低到0 . 5hz ，起動次數相當頻繁，每小時高達600 - 800次，沖擊負荷大，過載能力要求較高。
  4. Eev should be selected for various refrigeration systems according to the thermal properties of refrigerants ; the discharge coefficient of eev is sensitive to the aperture and impulse quantity of eev ; when the eev structure is made, the discharge coefficient goes up with the lowering of evaporation temperature or goes down with the hoisting of the condensation temperature. it is le

    對于不同工質的冷藏集裝箱製冷系統，電子膨脹閥應該根據具體製冷劑的熱力性質選取；電子膨脹閥流量系數對孔徑和脈沖數比較敏感；在結構固定時，流量系數隨蒸發溫度的降低而升高，隨冷凝溫度的增加而增大，受過冷度變化的影響較小；電子膨脹閥的容量受孔徑影響最大。
  5. But the biggest impact was felt on the natural gas market, where prices surged 23 per cent, surpassing $ 12 per million btu

    但是天然氣市場受到的沖擊最大，價格飈漲23 % ，超過每百萬英熱單位12美元。
  6. And others are found, and the expression of minimum rate of energy dissipation of flow is re - derived based on the theory of minimum entropy production. ( 2 ) it will be pointed out that the entropy is different from the entropy production in a river system

    （ 2 ）指出河流系統中的熵與熵產生是兩個不同的概念，沖積河流在調整過程中，力求使水流的熵產生或能耗率趨于最小值，而不是使熵趨于最大值。
  7. The result and discussion show three conclusions. 1. sternoclavicular joint should berd backward as best as the subject can, 2. the best finish effect can be obtained when both hands lift behind and parallel the ground, 3. the rotation angle of the trunk should be within go degrees under the circumstance of hands lifting behind and paralleling the ground

    經由結果討論得知，受試者在沖線時，一、頸關節應盡最大能力向後彎曲，二、雙手向後擺置成與地面平行時，具有最佳的沖線效益，三、軀干扭轉時，在不影響雙手后擺成與地面平行的情況下，以不超過90度為范圍。
  8. This paper analyzed the theory of geneva mechanism, established the mathematical model, and optimized the parameters. this design can make the geneva mechanism run smoothly, and show an effective method of the link to cad system

    在分析了槽輪機構工作原理和設計中所存在的問題基礎上，建立了數學模型，並對參數進行了優化設計，有效地解決了槽輪機構在運動過程中的不平穩性，最大限度的降低了沖擊，為進一步和cad系統的連接提供了有效途徑。
  9. Through theoretical computation and experimental observation, it is put forward that the maximal depth of the scoured pits of the embankment is from ten to thirteen meters, and for several pits whose top are rinsed by main flow continuously, their scoured depth have reached twenty meters

    經過理論計算和試驗觀測研究，提出了仁存渡以下沙質河床，丁壩最大沖刷坑水深為10 ? 13米，個別受主流持續頂?的丁壩，最大沖刷坑水深可達20米。
  10. The results indicates that the cubic logarithm polynomials can accurately reconstruct the raw thermal images in the experiment, and can effectively suppress the interference to defect recognition caused by random noise and uneven heating in the pt testing of composite laminates ; the digital images from data reconstruction have clearer defect display or higher defect resolution than the raw thermal images, and the quadratic coefficient image of cubic logarithm regression shows the highest snr

    結果表明利用三次對數多項式回歸即可精確地重建本次實驗的原始熱像，同時能有效地克服復合材料層壓板脈沖熱像檢測中隨機噪聲和加熱不均效應對缺陷識別的干擾；經過數據重建后所作的數字圖像比原始熱像有更高的缺陷顯示度或分辨力，其中以三次對數多項式回歸公式中的二次項系數所作的數字圖像的信噪比最大。
  11. At last, an experiential power supply was made, and a series of experiments is done. a lot of high - frequency pulse current was superposed on dcen current, modulated the welding current waveform we required and optimized the energy distribution, which satisfied the basic requirement of cathode cleaning

    最後製作了一臺實驗電源，並進行了一系列的電弧實驗，通過在變極性電源電流dcen基礎上疊加一系列脈沖電流，調制出所需電流波形，實現輸出能量的最優分配，在滿足陰極清理的前提下，最大限度地提高焊接效率。
  12. Slurry erosion tests were carried out with the manufactured test apparatus in order to study the erosion properties of the polyurethane composites. the results show that the wear resistance of silicon dioxide reinforced polyurethane composites decreased with the increased amount of particles, and the wear resistance of the alunima reinforced polyurethane composites first increased but then decreased. the wear resistance of the alunima reinforced polyurethane composites processed with kh550 coupling agent were maximum at the volume content of 15 %

    試驗結果表明，聚氨酯復合材料的沖蝕磨損性能隨白碳黑體積分數的增大而降低，隨al _ 2o _ 3顆粒體積分數的增大先升高而後降低；經過偶聯劑kh550處理的al _ 2o _ 3顆粒增強復合材料耐磨性比經過kh560處理的復合材料高；經過偶聯劑kh550處理的al _ 2o _ 3顆粒增強復合材料在體積分數為15時具有最佳的沖蝕磨損性能。
  13. Radar emits wide pulse to ensure the distance, and gets narrow pulse by using corresponding pulse compression method when receiving. this is pulse compression

    脈沖壓縮是指雷達通過發射寬脈沖，保證足夠的最大作用距離，而接收時，採用相應的脈沖壓縮法獲得窄脈沖以提高距離解析度的過程。
  14. The compensator was h ( s ) = 2370s. the results of simulation showed that attenuation factor of the first order of the third control system was as much as ten times of the value of the system without controller

    通過模擬表明，採用速率傳感器，在前三塊帆板上布置壓電驅動器時，一階最大衰減因子為無控時的10倍，可以使脈沖衰減時間縮短15倍。
  15. The results showed that there was anomalistic crystal whose size reached nanometer grade in fine pvc ; it ' s about 80nm. the crystal structure was damaged by jet - milling, which induced the melting point of nanocrystal pvc decreased from 210 " c to 128 擄 c. the nanocrystal pvc induced the decrease. of plasicizing time and equilibrium torque and the increase of maximal torque, which showed that the nanocrystal pvc had self - plasticization in pvc composites

    通過sem 、 tem 、 ftir和dsc測試表明：氣流粉碎制得的pvc微粉中具有不規則納米晶體，尺寸在80nm左右；氣流粉碎破壞了pvc的晶體結構，使納米晶pvc的熔點從210下降到128 ；納米晶pvc使體系塑化時間、平衡轉距降低、最大轉距升高，具有自增塑作用；納米晶pvc的加入使pvc的沖擊和拉伸強度都有大幅度上升。
  16. In this paper, first discussed are the corresponding results in highway and dam constructions and the engineering characters of rock - fills are deeply analyzed, especially the relationships between gradation, strength and maximum dry density, long - term stability of fillers including earth - fillers and rock - fillers and some conclusions of use are drawn. by in - situ tests and researches on compacting mechanism of high - filled rock embankments, effecting factors on compaction, construction technology and shock compacting technology, obtained in this paper are the compacting technology of high - filled rock embankment and the optimal parameters of rolling compaction. by deeply research on the theory and methods of quality control of high - filled embankment, settled are the questions as quality detection method and control standard of high - filled rock embankment

    本文首先總結和分析了國內外公路和壩工行業已有的相關成果，深入探討了填石料的工程性質與最大幹密度、長期穩定性等之間的關系，得到了一些有益的結論；通過現場試驗路堤的試驗和對高填石路堤壓實機理、填石路堤壓實效果影響因素、施工工藝和沖擊壓實技術等研究，解決高填石路堤壓實工藝和最優碾壓參數控制等技術問題；通過深入研究填石路堤壓實質量控制原理和方法，解決高填石路堤壓實質量檢測方法和控制標準技術難題；解決高填石路堤沉降觀測技術問題，並根據沉降觀測結果研究高填石路堤地基和路堤沉降變化規律，得到了能預測沉降變化規律的「龔帕斯」成長曲線預測模型；根據工程實際，深入研究了邊坡穩定性的影響因素，得到了有益的結論。
  17. The limited - jerk control commands are designed by fixing on a jerk maximum to limit the varying ratio of the reference orders, then the optimal time delays are solved by minimizing the oscillation energy of flexible modes

    通過確定最大沖擊值，對指令信號的時間變化率加以限制來設計有限沖擊控制指令，然後令柔性模態振蕩能量最小，計算濾波器的最優時滯。
  18. In this paper, we study the performance of input - buffered atm switching with window - access scheme and output - grouping architecture. the close - form formulae of maximum switch throughput, mean cell delay and cell loss probability are obtained by probability generating function approach. the accuracy of theoretical analysis is verified by computer simulations and results show that the maximum switching throughput will reach 99 % under random uniform traffic when the window size and the group size are 4 and 16 respectively

    本文提出了具有組合的窗口接入和線群輸出結構的輸入緩沖atm交換網路並對其性能進行了研究.通過概率生成函數方法得到了計算該交換網路最大吞吐率，平均信元時延和信元丟失率的封閉表達式，並通過計算機模擬實驗驗證了理論分析的精確性.研究結果表明，在隨機均勻業務下，當窗口尺寸和輸出群尺寸分別為4和16時，最大吞吐率可達到99
  19. Especially, we ' re developing agricultural industry, advancing establishment of famous agricultural products, the most important to agriculture is to protect geographical indications of such products. as regard to the problems existing in china at present, although the protection of geographical indications has been regulated in the law, people do n ' t understand the significance of it yet, the way of protecting geographical indications is n ' t practical and the contradiction between two administrative authorities make producers and their associations awkward and puzzled. as regard to the advice on how to strengthen the protection of geographic

    關於我國地理標志保護現狀及存在的問題:我國目前的現狀是雖然相關的法律有基本規定，但太過于原則，如地理標志保護意識未完全確立，地理標志被濫用，保護方式不切實際，尤其行政管理體制上的沖突是地理標志保護工作面臨的最大困擾，由於兩個管理部門管轄權限的條塊分割，造成了沖突和矛盾，使廣大企業及作為注冊人也是管理人的行業協會或其一
  20. The problem that ommt resulted in pvc degraded was settled. but na - mmt in pvc / na - mmt composite was simply common filler, the space of the layers was 1. 29nm

    通過力學性能測試發現，在蒙脫土含量為7phr時，硬質pvc的缺口沖擊強度最大提高了108 % ，彎曲模量也有所提高。
分享友人
分享到 Line

分享到臉書