核力參數 的英文怎麼說

中文拼音 [hélìshēnshǔ]
核力參數 英文
nuclear force parameter
  • 核 : 核構詞成分。
  • 力 : Ⅰ名1 （力量; 能力） power; strength; ability; capacity 2 [物理學] （改變物體運動狀態的作用） forc...
  • 參 : 參構詞成分。
  • 數 : 數副詞（屢次） frequently; repeatedly
  1. In view of bearing capacity of the elastoplastic theory analysis, the author made a comparison between the achieved bearing capacity limit load pi / 4 of round base ( space problem ) and the limit load pi / 4 of bar groundwork foundation design ( plane problem ) from soil mechanics at home and abroad as well as foundation criterion, and explained why the value of formula in present design criterion from soil mechanics is inclined to be conservative. in the light of the author ' s many years experience of vibration test on the spot and the research work of relevant projects, the author worked over the dynamic pile testing of the bearing capacity of foundation and batholith, and gathered the parameter of dynamic analysis and testing. the author also talked over the difficult point of pile foundation design criteria in present batholith engineering world, i. e. the confirmation of batholith bearing capacity of pile end, from the following aspects : a ) confirmation of single axis counter - pressure strength of rock in house ; b ) f. e. m calculation of elastoplastic model ; c ) calculation of soil mechanics ; d ) deep well load test

    然後，對巖土工程領域至今尚未解決，甚至不為人注意的考慮地基變形的地基承載力問題進行了實用化的探討，提出了考慮地基變形的地基承載力上程計算方法；對基於彈塑性理論分析的地基承載力國內尚未見報道的空間問題得到了圓形基礎（空間問題）的承載力界限荷載p _ （ 1 / 4 ） ，並與國內外土力學專著及地基基礎設計規范中的條形基礎（平面問題）的界限荷載p _ （ 1 / 4 ） ，進行了對比，從而定量上解釋了目前設計規范引用土力學承載力公式值偏於保守的這一情況；根據本文作者多年從事現場地基工程振動試驗及相關課題的研究工作，本文以截頭錐模型模擬地基，對地基（巖基）承載力的動測法進行了研究，為各類地基（包括巖基） ，匯總了動力分析和檢測川的參數：針對日前巖土工程界應用樁基設計規范中的難點? ?樁端巖基承載力的確定問題，從巖石室內單軸抗壓強度確定、基於彈塑性模型的有限單元法計算、土力學計算及深斤載荷試驗四方面進行了深入討論；本文作者根據多年現場載荷試驗的工程實踐，對深井荷試驗裝置的核心部分? ?反力裝置，設計了側壁支撐反力加載系統，該加載系統具有實用、簡便、穩定及安個等優點。
  2. Finally, the stress and strain distributions of dam foundation in which there have glacis weak surfaces are studied by means of nonlinear fem. with deducing parameters of weak surfaces gradually, stability of the dam against deep sliding is verified. therefore safety of dam and foundation would be estimated

    5 、運用非線性有限元法研究了東張水庫重力壩含有緩傾角軟弱夾層的壩基應力、應變情況，用逐步降低夾層材料參數的方法核算大壩的抗滑穩定，以此評價大壩及壩基的安全性。
  3. This article contains three parts, five chapters. the first part introduces the incentive models of actual bonus stock synoptically, analyses the stock on hand, option shares and stock option, the three kind of important incentive models, on rights and incumbencies, value and the incentive guidance by contrast. the second part discusses the difficulties and influential factors in the design of technical bonus stock, quests for the incentive models of technical bonus stock, analyses superiority and inferior position in action, difference and interosculation between them, discusses the need and significance for the technical bonus stock reanimation in the middle - small technicalfilms. in order to make use of the technical bonus stock distribution mechanism fully, inspire the talent of technologists, encourage their devotion to films, we have some important discussion on the technical bonus stock distribution policy, introduce the distributed models of technical bonus stock, point out the questions in the excutive course, and offer the solution correspondingly. in the third part, we discuss the technical stock option design on middle - small technical films, and consider the logical thoughtfulness in the course of reanimation as follows : the more outstanding achievement for the powered man the more increase on special target the lower price on technical option premium the more profit the more effective reanimation. in the parameter, a set of detailed program is designed, which includes establishment of incentive fund, institution of merit system for the plan ' s grantors, award of stock option, determination of premium, so as to reduce random in the incentive course, have a great effect on the mormative management for the

    本文內容共分為五章三大部分，第一部分概括性地介紹了現行股權激勵方式，對現股、期股和期權這三種重要的激勵方式，從權利義務、價值和激勵導向三個方面進行了對比分析；第二部分探討了技術股權設計的難點和影響因素，討論了我國中小科技企業技術股權激勵的方式，分析它們在激勵中的優勢和不足，以及它們之間的區別與聯系，並對中小科技企業實施技術股權激勵的必要性和意義進行了探討。在文中還重點討論了中小科技企業技術股權分配的策略，介紹了技術股權紅利分配方式，指出在技術股權激勵過程中應注意的問題，並提出相應的解決辦法，目的在於充分利用技術股權分配機制，來激發技術人員潛在的創新能力，激勵他們為企業作貢獻；第三部分著重探討了中小科技企業技術股份期權的方案設計，在激勵方面，按照技術期權獲受人的業績越突出特定的指標增長越快行權價越低獲利越多激勵效果越好的邏輯思路進行考慮；在參數設計方面，對技術期權計劃中激勵基金、授予和考核、行權價格等參數進行了詳細地分析設計，旨在減少技術期權激勵過程中的隨意性，為中小科技企業的規范化管理起到一定的指導和借鑒作用。
  4. Modbus transducer is the key device in the system and is used to offer power supply of pressure and temperature sensor, to collect signal, to linearizate and compensate temperature, to calculate density, volume and mass, to transmit data to modbus network, and display the data. so the modbus transducer is a multi - parament measurement, intelligent control device which can manage multi - signal

    變送器是系統的核心設備，其作用是為油罐溫度、壓力、液位、可燃氣濃度等傳感器供電，採集傳感器信號並進行線性化、溫度補償等處理，完成密度、體積和質量等參數計算，將數據輸出到modbus現場總線測控網路，根據需要現場顯示計測量參數。
  5. Hollow ferrites particles are the alternative to conventional solid ferrites particles, which have lower density, larger specific surface area and stability. moreover, it is expected electromagnetic wave can be reflected and absorbed again and again in the cavum of hollow particles which become its black hole. in addition, their electromagnetic parameters can be adjusted in a certain range by changing the thickness of the shell and the diameter of hollow microspheres, and the ability of absorbing microwave can be expected to improve

    空心結構的鐵氧體是對傳統實心鐵氧體的改造，不僅密度小，還具有特殊的電、磁功能，有可能使電磁波在其空腔中反復振蕩吸收，成為電磁波的「黑洞」 ，從而增加材料的吸波能力，同時可通過調節核殼粒子的內外徑來調控電磁參數。
  6. In chapter four, according to the analysis on the boundary theory and velocity field of main fluid zone of two - phase fluid pumps, the parameter equations of vane ' s modular curve of centrifugal pump are given, which contact the boundary " layer and eular theory of two - phase fluid pump by the fixing angel of vane as variable and leading into the velocity coefficient a. the results show that, in designing process of vane ' s modular curve of centrifugal pump, the determination of the total shape and parameters relates the flow properties of two - phase fluid and output ability of pump, or the design of the modular curve of centrifugal pump is the kernel of hydraulic design

    第四章依據固液兩相流泵的邊界層理論及對主流區速度場的分析，給出了離心泵葉片型線的參數方程；它是以葉片安裝角為參變數，以引入的速度系數k _ v作為中間因子，將兩相流泵的邊界層理論和歐拉理論聯系起來? ?它說明了這樣一個事實，在離心泵葉片型線的設計過程中，它的整個形態或參數的確定都關繫到兩相流體的流動特性和泵的輸出能力，或者說，離心泵型線的設計是其水力設計的核心。
  7. 3. on boiler retrofit, the calculation of fuel burning, the heat calculation of boiler inside structure and convection section, and the design of structure parameter of feed water heat exchanger are made. the flue gas channels " resistance calculation and the boiler strength verifying are also carried out. replacement of water cooling wall improves heat exchanging and decreases loss of heat radiant

    對鍋爐本體進行了燃料燃燒計算、爐膛結構熱力計算、對流受熱面結構熱力計算、鍋爐給水加熱器結構參數設計、煙道阻力計算及鍋爐元件強度校核等；改進了水冷壁布置使換熱效果更好，減少輻射換熱損失；改進對流段結構，更充分的利用爐膛出口煙氣余熱，提高熱效率；並且進行了煙氣阻力計算、熱效率計算和能量平衡測試，對改進后的稠油燃料和改進前進行了對比，燃燒狀況和熱效率有明顯改善。
  8. Introduced working state real time monitoring and testing, fault diagnosis system and its key instrument, including the working principle of torsion, axial force, rotary speed as a whole sensor, the main parameter index of oil well using progressing cavity pump

    介紹了螺桿泵採油系統工況實時監測與故障診斷系統及其核心儀器：扭矩、軸向力、轉速一體化傳感器工作原理、主要參數指標。
  9. Abstract : introduced working state real time monitoring and testing, fault diagnosis system and its key instrument, including the working principle of torsion, axial force, rotary speed as a whole sensor, the main parameter index of oil well using progressing cavity pump

    文摘:介紹了螺桿泵採油系統工況實時監測與故障診斷系統及其核心儀器：扭矩、軸向力、轉速一體化傳感器工作原理、主要參數指標。
  10. Aimed at design index of input power 1. 5kw, most output rotate velocity 300rpm, and rating output rotate velocity 150rpm, considering factors of angle and ratio of transmission, on the basis of kinematics simulation, author optimized the kinematics parameters. in this paper, author has made some analysis and study to the primal assembly condition of transformer ' s sequential action in theory, designed structure dimension of the input and output transformer, and verified the corresponding strengthen. further, the structure, which is to key transmission components of velocity control system of the speed regulator, has been designed based on meeting operational sensitivity, precision and self - locking

    本文針對輸入功率為1 . 5kw ，最大輸出轉速，額定輸出轉速的無級變速器的設計要求，並考慮到傳動角及變速比等因素，在運動學模擬的基礎上，對運動學參數進行了優化；本文對變換器連續作用的初始裝配條件進行了理論分析與研究，對輸入、輸出變換器作了結構尺寸的設計，並進行了強度校核計算；本文還對變速器調速系統中主要傳動構件在滿足操作的靈敏度、精度、自鎖性的基礎上進行了結構設計；最後採用workingmodel3d軟體，進行虛擬樣機的計算機輔助模擬設計及運動學和動力學計算。
  11. First, after the overall structure of the differential balance mechanism is determined considering the given requirement, the concrete structure of the mechanism is designed with the reference of the design method of the differential which is widely used in autos. the differential gearing system is optimized and more appropriate parameters are got with which the functional requirements can be satisfied and the weight of the mechanism can also be reduced. the surface type structure is adopted on the rocker shift, so the mechanical performance of the differential gearing system and the rocker shifts may be improved

    本文根據整車的性能要求確定了差動平衡機構的總體結構形式，以汽車驅動橋差速器及半軸的設計方法為參考，對差動平衡機構的原理樣機進行了完整的結構設計;對核心的差動輪系部分進行了優化，得出了既能滿足功能要求又可以有效減小機構質量的較合理的參數;在搖臂軸中使用了類似汽車驅動橋半軸的浮式結構，使搖臂軸所受彎矩大大降低，從而改善搖臂軸和差動輪系的力學性能。
  12. It has important theoretical meaning for reflecting the research of the interaction potential of nuclear force has important theoretical meanings in the framework of glauber theory and distorted wave impulse approximation ( dwia ), being spin - independent, inelastic scattering three low exciting states ( j * = 2 ~ ( + ), 4

    本工作的目的是藉助反質子-核散射來探索反核子-核子相互作用勢的最佳形式及相應的勢參數，對反映核力的相互作用勢的研究具有十分重要的理論意義。
  13. Discussion on the parameters of mine ventilation ability regulation

    礦井通風能力核定辦法中幾個參數探討
  14. Using the complex potential method in the plane theory of elasticity of an anisotropic body, the series solution of finite anisotropic thin plate containing an elliptical inclusion is proposed with the help of faber series. a hybrid element with an elliptical inclusion for anisotropic materials is obtained by using the hybrid variable principle, and the element efficiency is verified by numerical examples. the state of the damage is modeled by an elliptical soft inclusion, and using the point stress criterion based on characteristic curve and yamada - sun etc. criteria, the prediction of the strength of a composite laminate with damage is set up

    首先基於經典層板理論，將復合材料層板的彈性問題化歸為均勻各向異性板來求解；採用各向異性體平面彈性理論中的復勢方法，以faber級數為工具，給出了有限大含橢圓核各向異性板彈性問題的級數解形式；利用雜交變分原理，成功導出含橢圓核各向異性板雜交應力有限元，並用算例驗證了該單元的可行性和有效性；採用含剛度折減橢圓形彈性核的沖擊損傷模型，引入基於特徵曲線和yamada - sun破壞準則的點應力判據，建立了含損傷復合材料層板剩餘強度的分析方法；通過數值計算詳細討論了各種幾何參數對損傷層板應力分佈、剩餘強度的影響，得到了一系列對工程應用具有實用價值的結論。
  15. With the thermodynamic theories and techniques, it is relatively easy to determine the phase equilibrium data with enough accuracy, however there still exist much more difficulties in crystallization kinetics study even for a simple binary system. that is the reason that nucleation and crystal growth rate are generally represented in form of the empirical expressions. the crystallization kinetic is important for crystallizer design, process control and optimization, and it is strongly depended upon the accurate characterization of process information concerning with multiphase flows and the further disclose of its mechanisms with suitable mathematical models

    熱力學理論和方法已足以獲得準確的相平衡關系；然而即使對于簡單的二元物系的結晶過程，晶核形成和晶體生長動力學的研究仍面臨許多困難，通常採用經驗模型表述，而動力學參數的準確性和可靠性是結晶器放大設計、過程式控制制與優化的關鍵，因此多相流信息的準確表徵、結晶機理的進一步揭示及建立起與之相適應的數學模型有著十分重要的學術研究和實際應用價值。
  16. The design undertaken mainly from the following aspects : 1, mechanism ddesign : included the base and the joints : 2, trasmission mechanism design : adopted a synchronous toothelike transmission bell ; 3, balance system design : adopted springs and a brake and a lay air cylinder ; 4, design parameter and verify alculation ; 5, established motion equation by d - h method ; 6, simulated the motion locus by matlab software ; 7 ^ mapping out the part drawing or asesembly drawing

    本設計主要是從以下幾個方面入手： 1 、機構設計：包括底座和臂關節的設計； 2 、傳動機構設計：將驅動電機安裝在底座上，利用同步齒型帶、離合器傳遞手臂的動力；利用齒輪傳動帶動底座回轉； 3 、平衡系統設計：採用了彈簧平衡系統、電磁式制動器和單向延時氣缸； 4 、設計參數和校核計算； 5 、用d ? h法建立運動學方程； 6 、利用matlab軟體對手臂的運動空間進行模擬； 7 、利用autocad2000繪圖：包括零件圖和裝配圖。
  17. Considering that the characteristics of our country ' s highway tunnels are always of long spans, tabular and of various geometry, by means of thorough analysis of the different problems existed in the design of support structures of the tunnels at present, this paper pays special attention to the two key problems, optimization method of form selection of structural section of the tunnel as well as the stability and bearing capacity of the support structures, in the design of the long and large tunnel on high - class highway, introduces the simplified complex - form optimum method in the structure optimization theory, discusses the optimum design model of lining section of highway tunnel with satisfying demands in building clearance, ventilation and load conditions, puts forward an optimization method of form selection of three different kinds of lining sectional forms ( i. e. single - center circle, three - center tabular circle and three - center sharp circle ), establishes a complete set of systematic optimum design the ory and method of long and large tunnel on high - class highway, develops the corresponding computer software used on the planned xuefeng mountain highway tunnel on shaoyang to huaihua expressway in hunan province for optimization of form selections of the structural sections, and obtains a series of relatively reasonable structural design parameters

    本文針對我國公路隧道多為大跨度、扁平、幾何形狀呈多樣化的特點，通過深入分析目前隧道支護結構設計中存在的各種問題，抓住高等級公路長大隧道設計中隧道結構斷面的優化選型及隧道支護結構的穩定性與承載能力兩個核心問題，引入結構優化理論中的簡易復合形優化方法，深入探討了滿足建築限界、通風條件、受力狀態約束等條件下公路隧道襯砌斷面優化設計模型，提出了三種襯砌斷面形狀（單心圓、坦三心圓和尖三心圓）的優化選型方法，建立起一套完善的高等級公路長大隧道的系統優化設計理論與方法，並開發出相應的計算機程序，用於擬建的上海至瑞麗國道主幹線湖南省邵陽至懷化高速公路雪峰山長大高速公路隧道的結構斷面優化選型，得出了一系列較為合理的支護結構設計參數。
  18. Based on analyse of parameters which used to evaluate laser beam quality at present and according to the main properties which influence on laser manufacturing, beam focus characteristics parameter is put forward as the stander parameter to evaluate beam quality, because the foundmental advantage of laser beam applied in industral field is that laser beam can achieve high energy intensity through focusing

    論文在總結目前存在的評價激光光束質量參數的基礎上，根據對影響激光製造的主要光束特性參數的分析，以光束空間特性為核心，提出用光束聚焦特徵參數值作為評價激光光束質量的參數。因為激光作為能源能夠在工業領域廣泛應用的根本優勢就在於它可以通過聚焦獲得極高的能量密度，而值恰恰表徵了實際光束的可聚焦能力。
  19. The precipitation sequence is. - supersaturated solid solution - stoicheometric " phase - growth. with the increase of the composition there is more characteristic of non - classical nucleation and growth, and the order parameter values of critical ordered nucleus decrease. the precipitation sequence is : supersaturated solid solution - nonstoicheometric ordered phase - stoicheometric " phase - growth

    隨濃度增加，大部分亞穩區合金沉澱非經典形核長大的特徵增強，有序相臨界晶核序參數分佈曲線降低，且分佈更加平緩，沉澱序列為：過飽和固溶體非化學計量比有序相化學計量比相長大，非化學計量比有序相併非熱力學意義上的亞穩相，研究工作明確了這一點。
  20. The parametrization three - dimensional construction drawing and engineering drawing of new - style three - disk - cycloid - driving were established on the basis of the precise force analysis and optimization design of the parameters of new - style three - disk - cycloid - driving ; the design and experimental verification of sfa45 - 59

    本文通過對三片擺線輪新型針擺傳動系列精確的受力分析，強度校核及參數的優化設計，研製了sfa45 ? 59普通型樣機並且通過了試驗驗證，從而建立了整個系列的參數化設計三維圖庫和工程圖庫。
分享友人
分享到 Line

分享到臉書