模壁摩擦 的英文怎麼說
中文拼音 [móbìmócā]
模壁摩擦
英文
die wall friction-
By analyzing and experimentally verifying the model, new ways of improving mixer performance were put forward. ( 1 ) heat water should be used in the mixer ' s temperature control to make the mixer work with optimal parameters. ( 2 ) the surface materials of the mixing chamber and rotors should be chosen rationally to change material surface energy and increase friction on them. ( 3 ) when the compound was processed under higher pressure of floating weight, shallow groovers or stripes parallel to the axle of the rotor should be made on the mixing chamber internal wall to increase the real contact area and improve mixing effect
通過對模型的分析和實驗驗證，提出了提高密煉機混煉效果的新途徑： （ 1 ）密煉機溫度控制採用溫水冷卻，使密煉機處于最佳工作狀態； （ 2 ）通過合理選擇密煉室和轉子表面材料以改變材料表面能來增大膠料與它們之間的摩擦力； （ 3 ）在上頂栓壓力較大的條件下，在密煉室內壁與轉子軸線同方向加工淺的光滑槽可明顯改善混煉效果。In the paper, the finite element simulation software dynafrom is applied to analyze the affect of different blank holder during the forming process of laminose stepped tubular part, predict the possible defects such as wrinkle and break, obtain the rational style of blank holder avoiding the occur of defects and determine the rational configuration of die. the forming affect of thin - wall shallow stepped tubular part is analyzed when using different lubricate condition ( friction coefficient ). by this method, the relationship between friction coefficient and drawing depth of laminose stepped tubular part is obtained
本文利用有限元模擬軟體dynafrom分析了不同類型的壓邊圈對薄壁階梯筒形件成形過程的影響規律，預測了採用不同類型壓邊圈時可能出現的成形缺陷如起皺和拉裂，獲得了防止缺陷產生的合理壓邊圈形式，確定了合理的模具結構形式；分析了不同的潤滑條件（摩擦系數）對薄板階梯筒形件成形的影響，獲得摩擦系數與薄板階梯筒形件的拉深深度的關系；分析了階梯筒形件成形過程中的不同階段的應力應變分佈、毛坯材料厚度變化情況，並獲得了階梯階梯筒形件能一次拉深成形的條件。Based on the review, the fluid flow and heat transfer in the curved circular and rectangular pipes have been researched by employing perturbation method and numerical simulation with a physical model under the rotational orthogonal curvilinear coordinate in a rotating curvilinear pipe with multi - parameters. we firstly analyzed the fully developed fluid flow and heat transfer, mixed convection heat transfer, the development of flow and heat transfer in the inlet in different cross section ( circular, elliptical, annular and rectangular crossection ). the variations of the secondary flow, axial velocity, distribution of temperature, the friction force on the wall, the ratio of friction factor as well as the nusselt number with different dimensionless parameters had been examined in detailed
本文在總結和分析了一個世紀以來有關曲線管道流動和換熱特性的研究成果的基礎上，以旋轉正交曲線坐標系統下的多參數旋轉螺旋管道中的對流傳熱為物理模型，通過攝動方法和有限體積法，首次對各種截面（圓截面、橢圓截面、環形截面、矩形截面）旋轉曲線管道內充分發展流動的流動結構和傳熱特性（包括耦合對流傳熱特性）以及旋轉曲線管道開口段發展流動的流動結構和換熱特性進行了系統的數值模擬和理論分析，詳細討論了各種無量綱參數對管道內軸向速度分佈、二次流結構、溫度分佈、壁面摩擦力、摩擦系數比以及管道nusselt數的影響，獲得了若干創新性成果。In order to improve the prediction accuracy, the sensitivities of pipe friction coefficients, pressure loss coefficients in bents, wall temperatures and heat transfer coefficients in pipes and cylinders on the volume efficiency are investigated
為提高充氣效率的計算精度，由模擬計算和相關試驗，分析了管道的摩擦系數、彎管的壓力損失系數、進氣管壁和氣缸壁溫度及其傳熱系數對充氣效率的影響程度。The preferences are analyzed, pipe ’ s parameters such as depth, thickness, pipe diameter, and mechanical property of material ; soil parameters such as soil types, internal friction angle, pipe - soil interaction ; fault ’ s parameters such as fault types, fault throw, fault drop, fault - pipe angle, mechanical property of material ; load types such as gravity force, linear displacement load, seismic load and seismic wave. some conclusions are drawn from the calculating results : when buried pipes cross fault, pipe ’ s embedded depth should be shallow, and big pipe diameter and thick wall should be selected. avoid the site where fault moves severe, and select suitable pipe - fault angle
在有限元三維模型建立中考慮的因素有:管道自身參數如管道埋置深度、管壁厚度、管徑、管道材料等;巖土材料參數如土體類型、巖土的內摩擦角、管土相互作用等;斷層考慮有斷層類型，斷層斷距，斷層錯動距離，斷層與管道的交角，斷層材料的考慮等;荷載分別考慮靜荷載，動荷載，其中動荷載包括線性位移加載、地震力加載和地震波加載等。The peculiar mechanical character about pumping liquid concrete is discussed. based on the supposition that the ability of transferring hydraulic pressure of liquid concrete is orthotropic and the friction forces exists between concrete and steel tube, the pressure formulas of liquid concrete and the allotting formulas of deadweight are reasoned out. a new method is brought forward for allotting deadweight of liquid concrete during simulation analysis in pumping - core - concrete construction phase, which improves the calculation precision
在探討泵送液態混凝土的特殊的力學性質基礎上，在假定液態混凝土傳遞壓強能力為正交各向異性、混凝土與鋼管壁之間的存在有摩擦力的前提下，推導出液態混凝土壓強公式和自重荷載的分配公式，提出了在進行鋼管內混凝土灌注過程的施工模擬分析時處理液態混凝土自重荷載分配的合理方法，從而提高施工模擬分析的計算精度。分享友人