殘余組構 的英文怎麼說

中文拼音 [cányúzǔgòu]
殘余組構 英文
relict fabric
  • 殘 : Ⅰ形容詞1 （不完整; 殘缺） incomplete; deficient 2 （剩餘的; 將盡的） remnant; remaining 3 （兇惡...
  • 余 : Ⅰ動詞（剩下） remain; leave: 9減4 余 5。 nine minus four is five ; four from nine leaves five ; i...
  • 組 : Ⅰ名詞1 （由不多的人員組成的單位） group 2 （姓氏） a surname Ⅱ動詞（組織） organize; form Ⅲ量詞（...
  • 構 : Ⅰ動詞1 （構造; 組合） construct; form; compose 2 （結成） fabricate; make up 3 （建造; 架屋） bui...
  1. The variations in trace element contents and ratios may hold up a mirror to the lake - level fluctuations and climatic changes, which, in turn, have exerted a direct and important effect on the sequence stratigraphic development. collectively, the reservoir rocks from the yanchang formation consist dominantly of the delta front subfacies subaqueous distributary channel and channel - mouth bar microfacies and delta plain subfacies subaerial distributary channel microfacies fine - grained feldspar sandstones and siltstones. the reservoir rocks have been subjected to three stages of diagenetic and porosity evolution : ( 1 ) the porosity reduction by the mechanical compaction and chemical pressure solution during the early diagenetic stage ; ( 2 ) the porosity increase by the dissolution during the a substage of the late diagenetic stage, and ( 3 ) the porosity reduction by the cementation and filling during the b substage of the late diagenetic stage

    系統的儲層特徵研究表明，該區延長組儲層成因類型主要為三角洲前緣水下分流河道、河口砂壩及三角洲平原水上分流河道微相細粒長石砂巖、粉砂巖；儲層巖石經歷了壓實，膠結，溶蝕等成巖作用，歷經早成巖機械壓實和化學壓溶孔隙縮小期、晚成巖a亞期溶蝕作用孔隙擴大期及晚成巖a亞期（ b亞期）膠結充填孔隙縮小期三個成巖-孔隙演化階段；儲層物性總體上具有較低孔滲、低孔滲的特點，孔隙類型主要為粒間溶孔、殘余粒間孔隙、粒內溶孔、晶間孔及晶間溶孔，裂縫不發育，儲集巖排驅壓力和中值壓力較高，孔隙結構類型以細小孔-微孔隙，微細喉-微喉型為主。
  2. The study work in the dissertation is an important part of the tenth five - year defence advanced research project of “ study on control technology of the machining distortion for complex structure parts ” supported by pla general armament department of china. theoretical analysis and experimental study are carried out on the initial residual stresses and their effects on milling distortion for thick aero - aluminum - alloy plate

    本文作為總裝備部「十五」預研項目「復雜結構件加工變形控制技術研究」的主要組成部分，以航空鋁合金厚板為對象，研究重點定位在其初始殘余應力分佈規律及其對數控銑削加工變形的影響。
  3. Residual stresses developed during heat treatment are caused by : ( 1 ) thermal gradients within the metal, ( 2 ) nonuniform changes in the metallurgical structure, and ( 3 ) nonuniformity in the composition of the metal itself, such as that caused by segregation

    熱處理中產生殘余應力的原因有： （ 1 ）金屬中存在多級熱梯度； （ 2 ）金相組織的非統一變化； （ 3 ）金屬自身構成的非一致性，如隔離造成的非一致性。
  4. In the second, in allusion to non - stationary the characteristic of the signal, the author introduces to the method that using empirical mode decomposition to analysis the vibration signal so that the signal are made up of some intrinsic mode function, after this process, we can use stochastic subspace identification to identification the mode parameter of the structure and find the same work frequency

    其次，針對氣閥振動信號的非平穩特點，本文採用了經驗模式分解法（ empiricalmodedecomposition ）對振動信號進行分析處理，使之成為若干個基本模式函數imf （ intrinsicmodefunction ）和一個殘余量的線性組合。接著採用隨機子空間參數識別法對各個基本模式函數其進行結構參數識別，同時找出各種狀態的共同工作頻帶。
  5. ( 3 ) there are many flaws in direct laser metal sintering, such as the high remnants stress, micro - hole and micro - crack in sintering parts. in order to solving those problems, the programming of scanning paths is put forward, and several parts are prepared with different scanning paths respectively. the following conclusion is educed : the parts produced with short - side scanning path and same scanning direction have the minimum structure, the rigidity of parts prepared by short - side and same direction scanning path is highest, and the density of parts produced with the vertical scanning path is maximal

    （ 3 ）針對採用大功率激光直接燒結鎳基高溫合金成形金屬零件存在的問題，如較大的殘余應力，製件中存在著微裂紋、微孔洞等缺陷，初步提出掃描路徑的規劃，並採用幾種不同的掃描方式進行燒結試驗，發現採用短邊掃描路徑和同向掃描能夠獲得更加細小和分佈均勻的組織結構，採用短邊同向路徑制備的試樣其顯微硬度最高，而採用變向掃描（垂直）路徑制備的試樣緻密性最好。
分享友人
分享到 Line

分享到臉書