殘余組織 的英文怎麼說

中文拼音 [cányúzǔzhī]
殘余組織 英文
relict texture
  • 殘 : Ⅰ形容詞1 （不完整; 殘缺） incomplete; deficient 2 （剩餘的; 將盡的） remnant; remaining 3 （兇惡...
  • 余 : Ⅰ動詞（剩下） remain; leave: 9減4 余 5。 nine minus four is five ; four from nine leaves five ; i...
  • 組 : Ⅰ名詞1 （由不多的人員組成的單位） group 2 （姓氏） a surname Ⅱ動詞（組織） organize; form Ⅲ量詞（...
  • 織 : 動詞（編織） knit; weave
  • 組織 : 1 （組織系統） organization; organized system 2 （組成） organize; form 3 [紡織] weave 4 [醫學] [...
  1. Lateral aberrant thyroid rests may be found that are actually occult metastases with a benign histologic appearance

    可以發現一側迷走性甲狀腺殘余，實際上這是帶有良性組織表觀的癌的隱性轉移。
  2. The relations of metallography and remains austenitic to bearing ' s life

    軸承工作表面的金相組織和殘余奧氏體對壽命的影響。
  3. The results show that the solidification microstructure of high speed steel fe - 2 % c - 4 % v - 4 % mo - 5 % cr - x % w ( wt ) contains of martensite, retained austenite structure, and mc, m6c, m2c carbides, and mc / m2c complex carbides by xrd, sem and metallographs. most of the mc carbides locate in the cell and other carbides distribute along the boundary of the cell

    結果表明：經金相組織觀察、 x射線衍射和掃描電鏡分析， fe - 2 c - 4 v - 4 mo - 5 cr - x w合金系高速鋼凝固組織包含馬氏體基體、殘余奧氏體及各種類型的碳化物如mc型碳化物、 m _ 2c型碳化物、 m _ 6c型碳化物和mc m _ 2c類型復雜碳化物，大部分mc型碳化物分佈於晶粒內部，其它類型碳化物則沿晶界呈網狀分佈。
  4. The ultrasonic impacting has very good effect of adjusting residual stress, improving texture and raising fatigue strength of structural element, and it is particularly helpful to eliminate tensile stress in the shallow layer thereof

    摘要超聲波沖擊對于調整殘余應力、改善組織、提高疲勞強度都有很好的效果，特別對消除淺層拉應力有很大的幫助。
  5. Residual stresses developed during heat treatment are caused by : ( 1 ) thermal gradients within the metal, ( 2 ) nonuniform changes in the metallurgical structure, and ( 3 ) nonuniformity in the composition of the metal itself, such as that caused by segregation

    熱處理中產生殘余應力的原因有： （ 1 ）金屬中存在多級熱梯度； （ 2 ）金相組織的非統一變化； （ 3 ）金屬自身構成的非一致性，如隔離造成的非一致性。
  6. ( 3 ) there are many flaws in direct laser metal sintering, such as the high remnants stress, micro - hole and micro - crack in sintering parts. in order to solving those problems, the programming of scanning paths is put forward, and several parts are prepared with different scanning paths respectively. the following conclusion is educed : the parts produced with short - side scanning path and same scanning direction have the minimum structure, the rigidity of parts prepared by short - side and same direction scanning path is highest, and the density of parts produced with the vertical scanning path is maximal

    （ 3 ）針對採用大功率激光直接燒結鎳基高溫合金成形金屬零件存在的問題，如較大的殘余應力，製件中存在著微裂紋、微孔洞等缺陷，初步提出掃描路徑的規劃，並採用幾種不同的掃描方式進行燒結試驗，發現採用短邊掃描路徑和同向掃描能夠獲得更加細小和分佈均勻的組織結構，採用短邊同向路徑制備的試樣其顯微硬度最高，而採用變向掃描（垂直）路徑制備的試樣緻密性最好。
  7. This paper reviewed the modeling and experiments of the transient phenomena involved in the various subsystems of the thermal spraying process at home and abroad, such as : effect of process on droplets behaviors, microstructure, residual stress analysis and spray materials, and based on experimental resuts to discuss the droplets thermal - transfer discipline and effects on coatings properties

    摘要從熱噴塗工藝參數對塗層形成的影響、微觀組織及殘余應力分析和噴塗材料等幾方面對國內外熱噴塗塗層形成機理的研究進展進行綜述，重點綜述了工藝參數影響液滴行為的研究，並結合試驗探討了液滴的熱傳輸規律及對塗層最終性能的影響。
  8. This company produces the knitting center parts uses the material of completely high quality guards against rust the cast alloy iron, adopts the tertiary aging treatment of metal way, namely except hot aging treatment of metal, outside nature aging treatment of metal, each product in processing process, also must pass through the physical vibration aging treatment of metal process, guarantees each product the residual stress finally to obtain the elimination and the equalization

    本公司生產的編織中心組件所用材料，全部使用優質防銹合金鑄鐵，採取三重時效處理方式，即除熱師時效處理、自然師時效處理外，每件產品在加工過程中，還要經過物理振動時效處理過程，確保每件產品的殘余應力最終得到消除和均化。
  9. Because of the predominant role of the kinship governance at the preliminary stage of family business, it is impossible to eradicate it when employing the corporate system to reorganize the family business that has already grown up

    由於在家族企業初始化過程中，親族關系發揮了巨大的作用，所以家族企業發展壯大后，按公司模式制重新塑造企業組織時，必然會留有初始過程中利用親族治理企業的殘余。
分享友人
分享到 Line

分享到臉書