漸進接觸 的英文怎麼說

中文拼音 [jiānjìnjiēchù]
漸進接觸 英文
progressive contact
  • 漸 : 漸副詞（逐步; 漸漸） gradually; by degrees
  • 進 : 進構詞成分。
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 觸 : Ⅰ動詞1 （接觸） touch; contact 2 （碰; 撞） strike; hit 3 （觸動） touch 4 （感動） move sb ; sti...
  • 漸進 : advance gradually; progress step by step
  • 接觸 : 1. （交往） come into contact with; get in touch with 2. （沖突） engage 3. （挨上; 碰著） contact; touch
  1. Solid model of the involute worm gearing solid model with drive ratio 1 / 50 is built by using ideas - 5. 0, then the elastic contact analysis is proceeded on the basis of contact fem. the dynamic evolution image of the area of the contact zone, the load sharing among instantaneous meshing tooth pairs, the distribution of the contact force, and tooth stress are obtained. 3

    通過漸開線圓柱蝸桿、蝸輪的齒面方程式，利用ideas - 5 . 0軟體建立了傳動比為1 / 50的漸開線圓柱蝸桿傳動的實體幾何模型，在此基礎上應用接觸有限元方法對該傳動進行了彈性接觸分析，包括接觸區的形狀、位置、載荷在瞬時嚙合齒對的分配狀況； 3
  2. Firstly, the performance of several kinds of gears that is commonly used in present is analyzed. the sliding coefficients of the involute gear and the cycloidal gear are compared

    論文首先對目前常用的幾種齒輪性能進行了分析，比較了漸開線與擺線齒輪的滑動系數，漸開線與圓弧齒輪的彎曲應力和接觸應力。
  3. Contact pressure, hysteresis and no - even pressure ratio of no - gradual - enlargement finger seal under different length ratio and root circle of no - gradual - enlargement finger seal are constructed and analyzed, rules are summarized

    本文對非漸擴形結構指尖密封在不同寬度比和根圓外徑下的接觸壓力、遲滯率及偏載率等特性進行了作圖、分析，得出了相應的規律。
  4. Equations of mesh, shorting contact line, undercutting limit line, meshing limit lines and the existence conditions, angle between the direction of relative speed and the direction of contact line, induced normal curvature about every point on the contact line are established. moreover, the paper also theoretically analyzed the error of the grinded gear surface. on the basis of the theory, the computer program is worked out to automatically produce the contact line and the boundary curves of mesh. analysis of meshing circs under different parameters can be done so that we can gain the best process condition

    首先對漸開面二次包絡理論進行了深入的探討，推導出了兩次嚙合的嚙合方程式、瞬時接觸線方程式、根切界限線方程式、嚙合界限線的方程式及其存在條件，相對運動速度方向與接觸線方向的夾角及接觸線上各點的誘導法曲率；此外，還對磨齒后工件的齒面誤差進行了理論分析；並在理論基礎上編制了相應的計算機程序，自動生成接觸線族及嚙合界限線，對不同參數條件下的嚙合情況進行分析，可以使工藝條件達到最佳狀態；最後研究了磨齒裝置，設計了磨齒機的傳動系統。
  5. Analysis makes known, what it is along the progressive failure process of the slop that be able to more reasonably make known steady along slope actual situation, utilize contact friction spring element

    分析表明，邊坡穩定性分析的漸進破壞法能更合理地反映邊坡穩定的實際情況，利用接觸摩擦彈簧元可以有效地模擬這一過程。
  6. Secondly, the bending stress equations of asymmetric involute gear with two pressure angles are derived by the theory of isotropy wedge ; the contact stress equations of asymmetric involute gear are derived by the classical contact theory of hertz ’ s

    通過討論各向同性楔原理，推導了非對稱漸開線齒輪的彎曲應力的解析計算公式;利用赫茲公式對非對稱漸開線齒輪的齒面接觸應力進行了分析，推導了非對稱齒輪的齒面接觸應力的解析計算公式。
  7. The sliding coefficients, the bending stress, and the contact stress of the gears designed by the new method is calculated, compared with the involute gear

    對所設計齒輪的滑動系數、彎曲應力、接觸應力進行了計算，並與漸開線齒輪進行了比較。
分享友人
分享到 Line

分享到臉書