焊縫檢測 的英文怎麼說
中文拼音 [hànféngjiǎncè]
焊縫檢測
英文
weld seam detection- 焊 : 動詞(用熔化的金屬修補金屬器物或使金屬工件連接起來) weld; solder
- 縫 : 縫名詞1. (接合處) seam 2. (縫隙) crack; crevice; fissure; slit
- 檢 : Ⅰ動詞1 (查) check up; inspect; examine 2 (約束; 檢點) restrain oneself; be careful in one s c...
- 測 : 動詞1. (測量) survey; fathom; measure 2. (測度; 推測) conjecture; infer
- 檢測 : check; detection; test; gauging; detecting; sensing; [工業] checkout; measuring
-
Dye penetrant examination of the completed weld
對已完成的焊縫進行著色滲透檢測。Method of x - ray radioscopy for butt - weld
對接焊縫x射線實時成像檢測法According to the m1l - std - 883c standard of thermal cycle loading, the delamination propagation rates at the interface between chip and underfill were studied experimentally by using c - mode scanning acoustic microscope ( c - sam ) for two types of flip chip packages with different states of solder joint
採用mil - std - 883c標準,通過溫度循環實驗,使用高頻超聲顯微鏡( c - sam )無損檢測技術,測量了在不同焊點狀態下, b型和d型兩種實際倒裝焊封裝晶元與底充膠界面分層裂縫傳播速率。Recently, train is running faster and faster, and considering the stability and security, seamless welded rails ( swr ) are used as the train orbits gradually. the temperature of the rails will vary with weather. so that the rails may release the energy due to the metal characteristic of expanding or contracting with temperature, there is some badly distortion in the swr, worsly occurring accidents on expanding orbits. the portrait thermal stress ( pts ) of the swr should be monitored in some parts regularly, as to avoid such accident
近年來,隨著火車的提速造成的穩定和安全問題,軌道逐步轉為採用無縫焊接鋼軌,隨著鋼軌溫度的變化,無縫鋼軌可能會因為熱脹或冷縮的金屬特性並且在扣件阻力小而且路基較差的路段釋放能量,可能會發生鋼軌嚴重變形,更甚者會發生脹軌跑道等嚴重鐵道事故,為了避免發生如此事故,有必要定期對鋼軌的溫度應力進行檢測。Design of measurement and control system for impact cleaning equipment of container welding line
集裝箱外焊縫自動拋丸清理設備檢測控制系統設計Mechanized ultrasonic examination of girth butt welds in oil and gas steel pipeline
石油天然氣鋼質管道對接環焊縫.全自動超聲波檢測Non - destructive testing of steel tubes - automatic ultrasonic testing of the weld seam of electric welded steel tubes for the detection of longitudinal imperfections
鋼管的無損試驗.縱向缺陷探測用電焊鋼管焊縫的自動超聲波檢驗The paper expounds how to find out the potential safe problems and unobvious defects, such as beyond - limit deflection in fixed girders for gantry bucket wheel stacker / reclaimer, by means of completely checking fixed girders, movable beams, geometric shapes of stiff and flexible supporters, metal thickness and welding and how to solve the safe problems and remove the defects
摘要通過對門式斗輪堆取料機固定梁、活動梁、剛性支腿、撓性支腿的幾何形狀、金屬厚度、焊縫狀況、聯接螺栓狀況進行全面檢測,發現門式斗輪堆取料機固定梁存在下撓超標的安全隱患和其他非明顯缺陷,從而對堆取料機的安全狀況有了全面的掌握,並根據檢測結論對固定梁下撓缺陷及時進行校正消缺,避免發生設備垮塌事故,保證了堆取料機的安全穩定運行。The question of ultra - sonic inspection on weld defect detecting of net frame spherical shape contact point is introduced in this paper, the detected rate of weld defect of net frame spherical shape contact point was significantly increased by improving the ultra - sonic exploring block, ultrasonic sensitivity special standard reference block and reference block, and ultra - sonic inspection process method
摘要介紹了超聲波探傷技術在檢測網架球接點焊縫缺陷中存在的問題;通過對超聲波探頭、靈敏度專用標準當量試塊和參考試塊以及超聲波探傷工藝等的改進,提高了球接點網架焊縫缺陷的檢出率。The other way, theoretical analysis of weld tracking system with a leading sensor is stated, based on the analyzing of movement process of the tracking system, a loop control structure diagram is presented, the deuce vision feedback system is used and realized the repeated and automatic tracking in multiplayer seam and controlling of system of tracking and system of motion
同時就傳感器超前檢測式焊縫自動跟蹤系統進行了深入的理論分析,在分析該系統跟蹤過程運動關系的基礎上,建立了系統的閉環控制關系圖,並提出了其系統數學離散控制結構簡化圖。採用兩點式視覺伺服反饋系統,實現機器人在多層多道焊接時的重復自動跟蹤以及跟蹤機構的控制和焊炬橫向調節機構的控制,並使之協調聯動,滿足焊接過程的要求。At least five ( 5 ) percent of the welds are 100 percent radiographed or ultrasonically examined
至少5 %的焊縫進行100 %射線透照或超聲檢測。At least five percent of the welds shall be 100 percent radiographed or ultrasonically examined
至少5 %的焊縫進行100 %射線透照或超聲檢測。The application is not pressure retaining welds for pressure vessels or heat exchangers, unless such welds are fully radiographed or ultrasonically tested
此方法不能用於壓力容器或換熱器受壓部件的焊接,除非焊縫進行100 %射線透照或超聲檢測。Testing of filler metals by means of weld metal specimens ; test piece for determining the hardness for surfacing
用焊縫金屬試樣進行焊條檢驗測定堆焊硬度的試樣Abstract : in view of the quantity examination of weld defect by ultrasonic, on the basis of theoretical analysis and test, the cause, composition and contriling method of error of crack defect size h have been analyzed systematically, a controlling and statistical method of ultrasolic examination error has been put forward. this method is simple and suitable, and has been verified by test
文摘:針對焊縫缺陷超聲波定量檢測,從理論分析與實驗出發,系統分析了裂紋類缺陷自身高度尺寸h的檢測誤差的物理成因、組成及誤差控制方法,提出了一套實用簡潔並經實驗證實可行的超聲波檢測誤差控制及統計方法。Non - destructive testing of steel tubes - part 10 : radiographic testing of the weld seam of automatic fusion arc welded steel tubes for the detection of imperfections
鋼管的無損檢驗.第10部分:檢測缺陷用自動電弧焊鋼管焊縫的x射線照相檢驗Nondestructive inspection on welding seam of tube is required in the tube production, and real time x - ray radiography inspection is an effective means
在鋼管生產過程中需要對焊管焊縫進行無損檢測, x射線實時成象檢測是一種比較有效的檢測手段。Standard practice for x - ray real - time examination of cylinders weld
氣瓶對接焊縫x射線實時成象檢測We not only have realized the basic functions of the intelligent surveillance system based on mpeg - 1, but also made valid researches of its key techniques ( such as face detection and content - based image retrieval ) and its application in welding line detection. this is importantly worthy in academe and reality. moreover, it has brought great economic and social benefits
我們不但實現了基於mpeg - 1的智能監控系統的基本功能,還對其相關關鍵技術(人臉檢測、基於內容的圖象檢索技術)和智能監控在焊縫監測中的應用作了有效的研究,具有重要的理論意義和實際應用價值,同時也取得了良好的經濟效益和社會效益。A theoretical analysis is made on the influence of probe ' s near - zone length to the sensitivity and accuracy of ultrasonic inspection for the pipe welded seam, the issues in actual application of ultrasonic inspection technology is studied and the general countermeasures to increase the accuracy of ultrasonic inspection technology are given in the article
摘要從理論上對超聲波近場區長度影響管道對接環焊縫檢測靈敏度和準確性進行了分析,研究了超聲波檢測技術在實際應用中存在的問題,給出了提高超聲波檢測準確性的一般對策。分享友人