熱凝固劑 的英文怎麼說

中文拼音 [rènínggùjì]
熱凝固劑 英文
heat coagulant
  • 凝 : 動詞1. （凝結） congeal; curdle; coagulate 2. （注意力集中） fix
  • 固 : Ⅰ形容詞（結實; 牢固; 堅硬） firm; hard; solid Ⅱ副詞1 （堅決地; 堅定地） firmly; resolutely 2 [書...
  • 劑 : Ⅰ名詞1 （藥劑; 制劑） a pharmaceutical or other chemical preparation 2 （某些有化學作用的物品） a...
  • 凝固 : solidify; solidification; coagulation; congealing;clotting; hardening; solidifying; freezing
  1. Eev should be selected for various refrigeration systems according to the thermal properties of refrigerants ; the discharge coefficient of eev is sensitive to the aperture and impulse quantity of eev ; when the eev structure is made, the discharge coefficient goes up with the lowering of evaporation temperature or goes down with the hoisting of the condensation temperature. it is le

    對于不同工質的冷藏集裝箱製冷系統，電子膨脹閥應該根據具體製冷劑的熱力性質選取；電子膨脹閥流量系數對孔徑和脈沖數比較敏感；在結構固定時，流量系數隨蒸發溫度的降低而升高，隨冷凝溫度的增加而增大，受過冷度變化的影響較小；電子膨脹閥的容量受孔徑影響最大。
  2. Copper - nanosized tibi composites were prepared by in - situ process. the microstructure, mechanical and electrical properties, and dry sliding wear behavior and electric sliding wear of cu - nanosized tib _ 2 in - situ composites was investigated ; mostly task as follows : the thermodynamic data for the reactions between b and ti in the molten liquid of copper were analyzed, the copper matrix composites reinforced by in - situ tibi nanoparticles were prepared by reactions of 8263, carbon and titanium in copper - titanium melt, and copper - titanium, copper - boron in alloy melt, respectively, which controlled the reaction temperature, reaction time and solidification process. the rnicrostructure and mechanical and electrical properties of the in - situ composites were investigated by using optics microscope, tem and xrd

    本文採用原位反應法制備了cu -納米tib _ 2原位復合材料，在此基礎上分析了原位復合材料的微結構，進行了干滑動摩擦磨損和電接觸滑動磨損實驗，完成的主要工作如下：從熱力學的角度出發，分析了陶瓷tib _ 2顆粒在銅基體中原位生成的熱力學條件，並用電解銅、工業純鈦、 b _ 2o _ 3 、 c （還原劑）以及cu - ti 、 cu - b等合金為原料，通過控制適當的反應溫度、反應時間和快速凝固等工藝手段，制備了cu -納米tib2原位復合材料。
  3. Differential scanning calorimeter ( dsc ) combined with melt fluxing technique was used to realize undercooling of melt and its specific heat was measured at the same time, and its thermodynamics were calculated simultaneously and compared to four well - known models

    本文將差示掃描量熱法（ dsc ）和助熔劑處理技術相結合，研究了熔體的過冷現象，測量了過冷狀態下熔體的比熱，計算了過冷熔體凝固過程中的其它熱力學參數，並與四種近似模型進行了比較分析。
  4. Standard test method for effects of heat aging on weight loss, cracking, and chalking of elastomeric sealants after cure

    彈性體密封劑凝固后熱老化對重量損失裂開和粉化影響的標準試驗方法
分享友人
分享到 Line

分享到臉書